Question about 1984 Dodge Rampage

1 Answer

Dodge rampage transaxle

I have an 84 dodge rampage, never has shifted into 5th since i bought it. one day i had trouble getting it to shift into reverse, the next day it stopped shifting all together. the clutch is almost impossible to press down, makes a slight walloping noise, and pulsates a little.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

Warped pressure plate or throw out bearing .

Robert

Posted on Sep 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 pontiac sunfire auto shift control solonoide lacated


What are you talking about auto shift control solenoid ? Which transmission does yours have ?
Automatic Transaxle - 3T40 Automatic Transaxle - 4T40-E
1-2 Shift Solenoid Valve
In transmission valve body
Transmission Component Location
Automatic Transmission Internal Connector End Views
2-3 Shift Solenoid Valve
In transmission valve body
Is there a DTC - diagnostic trouble code stored ? Which gear or gears are not working ?

Jul 07, 2016 | Pontiac Cars & Trucks

2 Answers

Why won't 98 Buick century shift into any gear?


is it a linkage issue? if the shift lever is working and you can feel the detents, check your fluid make sure it is full and clean, if not you could have internal issues with the trans

Oct 30, 2015 | Buick Cars & Trucks

1 Answer

Dtc 0700 jerks when shifting from reverse to drive


The transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. When the TCM detects a malfunction with the control, a signal is send to the Engine Control Module (ECM) to trigger the Engine Light or Service Engine Soon light. The ECM stores the P0700 code and it means the TCM detected a malfunction with the transaxle controls.
Read more: http://engine-codes.com/p0700_dodge.html#ixzz3Pn5lTBcI

Mar 30, 2014 | 2005 Dodge Grand Caravan

1 Answer

1989 dodge dynasty v6, fwd, transaxle 3 speed auto, good condition, experiencing shift problem, doesnot want to shift into passing gear, sometimes it does, right now it doesn't, any takers


most auto trans don't shift into reverse when low. Reverse takes the most fluid of all the gears.
Check for a bad shift solenoid or wires to and from that circuit. Most trans-axles have them now.

Feb 25, 2013 | 1989 Dodge Dynasty

1 Answer

Loose timing belt on 84 dodge rampage. How to fix


You will need to check your timing gear and see if it is worn out. You will have to replace the timing cover gasket and a new timing chain.

Jul 05, 2010 | 1984 Dodge Rampage

1 Answer

Number 18 trouble shooting code


18 = Cam Crank Problem
36 = Transaxle Shift Problem

Hope this helps. - Jarett

The transaxle shift problem I am unfamiliar with, but the cam crank problem is probably either your Camshaft Position sensor, or Crankshaft Position Sensor.

Aug 17, 2009 | 1993 Buick LeSabre

1 Answer

'84 rampage bad tachometer


This is a case of pure coincidence. It just went bad at the same time you made the repair. Just a fluke,no worries.

Jun 23, 2009 | 1984 Dodge Rampage

1 Answer

I need to drop transmission but it's hooked up to something that won't let me drop it. i need to know what it can be that i have to remove.


Transaxle Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Attach a support fixture to the engine lifting eyes.
  3. Drain the transaxle.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Air intake assembly
    • Clutch slave cylinder
    • Speedometer cable
    • Shift cables
    • Starter motor
    • Axle halfshafts
    • Flywheel cover
    • Transaxle mount
    • Transaxle flange bolts
    • Transaxle
To install:

NOTE Use new circlips, split pins and self-locking fasteners for assembly.
  1. Position the transaxle to the engine and tighten the flange bolts to the following specifications:
    • M8 bolts: 72–84 inch lbs. (8–10 Nm).
    • M10 bolts: 22–25 ft. lbs. (30–35 Nm).
    • M12 bolts: 32–39 ft. lbs. (43–55 Nm).
  2. Install or connect the following:
    • Transaxle mount and torque the bolts to 65–80 ft. lbs. (90–110 Nm)
    • Flywheel cover and torque the bolts to 72–84 inch lbs. (8–10 Nm)
    • Axle halfshafts
    • Starter motor
    • Shift cables
    • Speedometer cable
    • Clutch slave cylinder
    • Air intake assembly
    • Negative battery cable
  3. Fill the transaxle.

May 06, 2009 | 2003 Hyundai Tiburon

1 Answer

1990 Toyota 4runner wont go into 5th or reverse


They had a problem with this plastic washer that is in the shifter tower it sits just under the shifter it self and gets worn out and causes this to happen- hope that helps.

Nov 03, 2008 | 1990 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...