Question about 2000 Dodge Grand Caravan

1 Answer

REMOTE KEYLESS ENTRY 99 GRAND CARAVAN

I HAVE A 99 GRAND CARAVAN I BOUGHT A RKE SYSTEM OUT OF THE SAME YEAR AND MAKE VAN. HOW DO I PROGRAM IT TO WORK ON MY GRAND CARAVAN? CAN I DO THIS OR IS IT A DEALER SHIP FIX?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

INSTALLATION: REMOVE THE TOP DASH COVER USING A FLAT TIP SCREW DRIVER AND LOCATE THE CONNECTOR FOR THE RKE MODULE. THE CONNECTOR WILL BE SMALL AND LOCATED NEXT TO THE HVAC DISTRIBUTION DUCT. MOUNT MODULE AND INSERT THE CONNECTOR. SINCE THE BODY CONTROL MODULE IS INVOLVED WITH THE RKE THIS MAY OR MAY NOT WORK BECAUSE NOT ALL CONTROLLERS ARE THE SAME BUT IF YOU WOULD LIKE TO TRY TO PERFORM THE TASK TRY THIS. FOR PROGRAMMING:

  1. Using a functional key fob transmitter, unlock the vehicle and disarm the Vehicle Theft Security System.
  2. Insert ignition key into the ignition switch.
  3. Turn the ignition switch to RUN position without starting engine.
  4. Using a functional key fob transmitter, press and hold the UNLOCK button for a minimum four seconds (maximum ten seconds)
  5. While holding UNLOCK button, and before ten seconds passes, press and release the PANIC button. A single chime will sound to verify that the RKE module is set to receive the new Vehicle Access Code(s)
  6. Within 30 seconds of the chime, press and release the "LOCK" and "UNLOCK" buttons on the transmitter at the same time. Then press any one of the buttons. The BCM will sound an abbreviated chime to acknowledge that the programming of the transmitter has been completed and was successful.
  7. Repeat step 6 for all transmitters that will be used with this vehicle (up to 4 total)
  8. Programming mode will last for 30 seconds. To get out of programming mode sooner, turn the ignition OFF. A single chime will sound to verify that the RKE module will no longer accept additional Vehicle Access Code(s)
  9. When Vehicle Access Code(s) programming is complete, turn the ignition switch to the OFF position and verify RKE system operation using each key fob

Posted on Sep 27, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the Ford 2010 Ford Explorer "Remote Keyless Entry (RKE) module" located


The RKE is controlled by the SJB - smart junction box ! Fords BCM - body control module .
Principles of Operation
Power Locks
The SJB controls the power lock/unlock feature of all of the vehicle doors, including the liftgate, to lock or unlock based on the input received from the door lock control switch, the keyless entry keypad or the remote keyless entry (RKE) transmitter. Power locking and unlocking of the doors function independently of the key position, vehicle speed or transmission position. The smart junction box (SJB) activates internal relays to supply the correct voltage and grounds for the door lock actuators.

Your best bet would be to take to ford dealer or some other qualified repair shop .
Remote Keyless Entry (RKE) Transmitter Lock/Unlock Control - Unlock
The RKE transmitter feature provides lock/unlock functions independently of key position, vehicle speed, or transmission position. The RKE transmitter feature provides a 2-step process for unlocking the doors. Upon receipt of the first request for unlocking the doors, the RKE control feature requests the SJB to unlock the driver door only. If another unlock request is received within 3 seconds of the first, the RKE transmitter feature requests the SJB to unlock all the doors. This feature can be changed to global unlock, so that all the doors unlock on the first press of the unlock button. To toggle between the 2-step unlock and the global unlock press the lock and the unlock button on the RKE transmitter at the same time and hold the buttons for 4 seconds. The turn signal lamps flash to confirm that the feature has been toggled.
Remote Keyless Entry (RKE) Transmitter Lock/Unlock Control - Lock
The RKE transmitter feature requests that all the doors be locked when the lock button is pressed. On any press of the lock button with all doors closed, the SJB provides 1 flash of the parking lamps. If any door is ajar, no flash occurs. As soon as the last door is closed, the SJB provides the flash of the parking lamps. If 2 presses of the lock button are received within 3 seconds, the horn chirps once, and the parking lamps flash twice to indicate that all the doors are closed and locked. If any door is ajar when the second lock request is received within 3 seconds of the first, the RKE transmitter feature requests the SJB chirp the horn twice without flashing the parking lamps to indicate it locked all the doors but 1 or more doors are ajar. When the key is in the ON or START position, the parking lamp flashes and horn chirp confirmations do not occur.

All locks not working ?????
  • The doors do not lock/unlock using the remote keyless entry (RKE) transmitter
  • RKE transmitter battery
  • RKE transmitter
  • RKE transmitter programming
  • Aftermarket system
  • SJB
  • Go To Pinpoint Test H .

Apr 16, 2017 | Ford Cars & Trucks

Tip

Do it Yourself: Reprogramming the Remote Keyless Entry (RKE)


Normal 0 21 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Tabla normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Jeep Grand Cherokee Alarm System (1993-1998)

I would try reprogramming the Remote Keyless Entry (RKE) transmitters before looking for anything else. Make sure the batteries in the RKE transmitters are good and replace them if in doubt. Here's the procedure for programming the RKE transmitters.

Up to 4 Transmitter Identification Codes (TIC's) can be programmed into the receiver at any given time.

1. Open the driver's door of the vehicle. Leave it open through the programming procedure.
2. Move the mechanical door lock lever to the LOCK position.
3. Insert the ignition key and turn it to the RUN position.
4. Turn the ignition to the RUN position. Within 20 seconds, aim a transmitter at the receiver dome and press the lock button, for at least 5 seconds. Once the receiver accepts the programming code the driver's door will unlock.
5. Once the first transmitter has been programmed, additional transmitters (up to 4) may be programmed into the receiver. Within 20 seconds of the previous transmitter programming, move the mechanical door lock lever to the Lock position. Aim another transmitter at the receiver dome and press the LOCK button for at least 5 seconds. The door lock will cycle again.
6. To lock the programmed codes into the receiver, the ignition must be turned off and back on within 20 seconds after programming the last transmitter's code. At that time, all previous codes are erased from the module.

If the alarm still doesn't work correctly, you probably have a bad Alarm Module. If you wanna download this procedure, clic the image.

79482d7.gif

Enjoy Jeep.

on Sep 23, 2009 | 1993 Jeep Grand Cherokee

1 Answer

99 JEEP GRAND CHEROKEE 4.7 LOST KEYS BOUGHT A NEW ONE THEY SAID CANT PROGRAM THE KEY.WHAT DO I NEED TO CHECK TO SEE WHY?


answered here 1000s of times, search much?

who is THEY/?
you mean lost both keys.! and the book.
car did come with 2 keys, a fact.
so that means what?, per your lost operators guide it tells you
only a key shop (pro graded and does cars)
or dealer can fix this.
there are mobile key makers, $$$$$$$$$$
tow it any shop and they do it, many shops cars repair have the very expensive tool to do this, call them ask?


the book also covers how you can make your own key (DIY)
and tells you that with zero keys you cant.
after all so could a thief,right and is the whole point of this.
some jeeps, most usa
are you usa.
takes 1 to make more
takes 2 to make more (my 2010 is this) so I have 4 now.
and limits you to 8 keys, it tells you that. there.

here is the factory manual direct quote
REMOTE KEYLESS ENTRY TRANSMITTER
PROGRAMMING
To program the Remote Keyless Entry (RKE)
transmitter access codes into the RKE receiver in the
Passenger Door Module (PDM) requires the use of a
DRB scan tool. Refer to the proper Diagnostic Procedures
manual for more information.
i uses a rolling encrypted code system
an is UN Hackable.

Jan 24, 2017 | Jeep Cars & Trucks

1 Answer

Both my keys FOBs on my 2000 Dodge Grand Caravan don't work, changed the batteries, still did not work. Bought 2 new ones and the dealer could not program them.


Programming a Replacement Keyless Entry Remote ' Filear ...

filear.com/?p=131
Oct 17, 2012 - If the transmitters don't work, or if you'd rather not match the transmitters yourself, .... Tried these instructions last night on my 2005 Grand Prix.

Key FOB Not Working - The Chrysler Minivan Fan Club Forums

forum.chryslerminivan.net/showthread.../11859-Key-FOB-Not-Working

Mar 15, 2009 - 10 posts - ‎3 authors
Hi Everyone, One of my Key FOB's stopped working. Is there a way of ... Well, to be honest, you don't know where that FOB has been? LOL ... 2009 Dodge Grand CaravanSXT (3.8L), Light Sandstone Metallic, 125K miles 2005 Volvo .... By jimmy154 in forum 3rd Generation Chrysler Minivans: 1996-2000.

Key May Not Start Car or Release From Ignition : Dodge ...

repairpal.com > Problems > Dodge > Grand Caravan
Dodge Grand Caravan Key May Not Start Car or Release From Ignition. ... If the newkey doesn't work, replacing the lock cylinder including tumblers ... I am able to turn off the van, but the key is stuck in the ACC position, draining my battery. ... In reading other comments, I see it may be the FOB so I'll carry both with me and ...

2009 Dodge Grand Caravan car lock doors not working


Jan 24, 2016 | 2000 Dodge Grand Caravan

1 Answer

Como reiniciar motor con bad key?


PDF]Download 2014 Dodge Grand Caravan Owner's Manual

www.dodge.com/download/pdf/.../2014-Grand_Caravan-OM-2nd.p... DodgeIt also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry

Aug 05, 2015 | 2008 Dodge Grand Caravan

1 Answer

Keyless remote stopped working, I replaced battery


The 1997 to 2003 Dodge Caravan and Grand Caravan use a standard key and remote setup with a separate remote fob. However, the 2004 to 2009 Dodge Caravan and Grand Caravan use a combination key and remote on one device. To program a new keyless entry remote for the 1997 to 2003 Dodge Caravan, you must have at least one functional remote, which is required to enter synchronization mode. To program the combination key for the 2004 to 2009 Dodge Caravan, you must have two functional combination keys. If you do not, you'll need to see an authorized Dodge dealer for keyless entry programming assistance.


2004 to 2009 Caravan Programming Instructions
  1. Insert one of your working combination keys into the ignition. Turn it to "On"; leave it in this position for about 10 seconds but no longer than 15 seconds. Turn it to "Off" and remove it.
  2. Insert your second working combination key into the ignition within 15 seconds of removing the previous key. Turn it to "On". After 10 seconds, you'll hear a chime and the "Theft" light will begin to flash, entering synchronization mode. Turn the key to "Off" and remove it.
  3. Insert the combination key you want to program. Turn it to "On." After 10 seconds, you'll hear a chime; then the "Theft" light will turn off. When the light turns off, the combination key--including the key and the remote--is programmed.
  4. Repeat Step Three for each combination key you want to program. A total of eight can be programmed.
Hope this help (remember comment and rated).


May 08, 2010 | 2008 Dodge Grand Caravan

1 Answer

Need to know how to program keyless remote on 98 cavalier


1997 Cavalier remote keyless entry programming.

All Remote Keyless Entry Modules may be programmed to receive four different
transmitters which all may be used to operate the remote control lock system on the
vehicle.

Also, severalvehicles, each with the same system may all be programmed to operate from the same transmitter or four different transmitters.

Step 1. Turn ignition off
Step 2. Ground the program pin.(within one second, Lock, Unlock and Trunk will cycle to indicate module ready for programming.)

**the program pin is the two wire connector plugged into the RKE reciever in the trunk of the vehicle at the Left Wheelhouse. Leave the main harness plugged in but unhook the two wire connector and ground the pins.**

Step 3. Press and hold the LOCK and UNLOCK buttons until:
Lock, Unlock, Trunk, and Horn cycles to indicate the transmitter has successfully been programmed. (This takes no more then 12 seconds)
Step 4. Repeat step 3 for the remaining number of transmitters
Step 5. Remove the ground from the program pin.
Step 6. Verify proper operation of the transmitters.

Keep in mind that 97-99 can be programmed by the owner, 00+ require DEALER programming with the scantool.

I hope helps with this (remember rated this help) Good luck.

Dec 29, 2009 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
2000 Dodge Grand Caravan Logo

621 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

71288 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7009 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...