Question about 2002 Jaguar X-Type

1 Answer

Oil Pan Gasket

Has anyone changed thhe oil pan gasket on a 2002 Jaguar X-Type 2.5L gas engine?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Yes i have and its a nitemare ,dares one bolt u can not get at becauce its under the drive train in the corner of the sump .to take out sump you have to take out drive train u will no what i am talking about if u have started the job..good luck to u mate..

Posted on Oct 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 s type 2.5L oil pan leak 1) Does anyone know


Hello your Dealer is going right by the book on labour now a day's garages are by law aloud to go by the book quote to do the job the book is about 7-8 hours but i have seen the job completed in 6.5 hours by someone who has allot of experience and has done several of them.So all in all they are aloud to go by the book and yes your quote is pretty much accurate and yes it is a big job hoist needed.

Jan 24, 2011 | 2003 Jaguar S-Type

1 Answer

How to change oil pan?


Step 1: Place car on jack stands or car ramps ( i prefer jack stands because i had a car ramp collapse on me once. not fun) and block the back tires.
Step 2: Loosen and remove the oil pan drain plug and drain oil into a drain pan
Step 3: Look on the outer edges of the oil pan and you will see bolts going all around the outside of the pan. Loosen them and the pan should come off.
Step 4: clean the surface where the gasket comes into contact with the engine, and if you are using the same oil pan peel the old gasket off and clean the surface on the oil pan where the gasket goes.
Step 5: Place the new gasket on the oil pan and stick the oil pan up onto the engine and stick a few bolts in on each side. Make sure the gasket stays aligned with all the bolt holes. You may use some RTV on the gasket but if the surfaces are good and clean you shouldnt have to
Step 6: tighten all the bolts to spec according to the repair manual for your vehicle
Step 7: Fill your engine with the correct type and capacity and then start the engine up and check for leaks
Step 8: Your Done!!

Jan 03, 2011 | 2000 Chevrolet Venture

2 Answers

What all has to be taken off to get to to the oil pan gasket


Oil Pan REMOVAL & INSTALLATION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the crankcase.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Oil level indicator harness connector, if equipped
    • Exhaust Y-pipe, if needed
    • Transaxle assembly from the vehicle.
    • Oil pan bolts and the oil pan
    To install: NOTE: The oil pan gasket is reusable unless it is damaged. Do not remove the gasket from the oil pan groove unless gasket replacement is required.
  4. Thoroughly clean the inside of the oil pan and the cylinder block contact surface. If the oil pan gasket is being reused, be careful not to damage it. Do not expose the gasket to cleaning solvents.
  5. If a new gasket is being installed, start the gasket into the oil pan groove and work the gasket into the groove in both directions. Once the gasket is exposed to oil, it will expand and no longer stay in the groove without wrinkles. If this condition exists, replace the gasket.
  6. Install or connect the following:
    • Oil pan. Torque the bolts, in sequence, to 89 inch lbs. (10 Nm).
    • Oil level indicator connector, if removed
    • Transaxle assembly, if removed
    • Y-pipe, if removed
    • Flywheel cover, if removed
    • Oil pan drain plug. Torque it to 15 ft. lbs. (20 Nm).
    • Negative battery cable
  7. Refill the crankcase.
  8. Run the engine and check for leaks. Fig. 1: Oil pan bolt torque sequence 7922vg08.gif
prev.gif next.gif

Jan 01, 2011 | 2002 Cadillac Deville

1 Answer

How to replace oil pan gasket on 2002 deville


Oil Pan REMOVAL & INSTALLATION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the crankcase.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Oil level indicator harness connector, if equipped
    • Exhaust Y-pipe, if needed
    • Transaxle assembly from the vehicle.
    • Oil pan bolts and the oil pan
    To install: NOTE: The oil pan gasket is reusable unless it is damaged. Do not remove the gasket from the oil pan groove unless gasket replacement is required.
  4. Thoroughly clean the inside of the oil pan and the cylinder block contact surface. If the oil pan gasket is being reused, be careful not to damage it. Do not expose the gasket to cleaning solvents.
  5. If a new gasket is being installed, start the gasket into the oil pan groove and work the gasket into the groove in both directions. Once the gasket is exposed to oil, it will expand and no longer stay in the groove without wrinkles. If this condition exists, replace the gasket.
  6. Install or connect the following:
    • Oil pan. Torque the bolts, in sequence, to 89 inch lbs. (10 Nm).
    • Oil level indicator connector, if removed
    • Transaxle assembly, if removed
    • Y-pipe, if removed
    • Flywheel cover, if removed
    • Oil pan drain plug. Torque it to 15 ft. lbs. (20 Nm).
    • Negative battery cable
  7. Refill the crankcase.
  8. Run the engine and check for leaks. Fig. 1: Oil pan bolt torque sequence 7922vg08.gif
prev.gif next.gif

Oct 29, 2010 | 2002 Cadillac Deville

1 Answer

What is the oil pan bolts torque spec for a 2002 jaguar X-type V-6


Fig. Oil pan bolt torque sequence-X-Type

b8259f9.jpg



  1. Use a new oil pan gasket. Tighten the bolts, in the sequence shown, to 18 ft. lbs. (25 Nm).
  2. Tighten the pan-to-transmission bolts to 33 ft. lbs. (45 Nm).
  3. Tighten the access cover bolt to 89 inch lbs. (10 Nm).
  4. Tighten the compressor bolts to 18 ft. lbs. (25 Nm).
  5. Refill the engine with oil.
  6. Install the transfer case.
Hope this helped (rememer comment and rated this).

Apr 14, 2010 | 2002 Jaguar X-Type

1 Answer

Difficulty in changing the oil pan gasket I dont have the car here to look at do I have to remove any type of crossmember bracing or is it a direct shot to remove it


It's a direct shot....

Removal & Installation
  1. Disconnect the negative battery cable. Raise and safely support the vehicle.
  2. Drain the engine oil into a suitable container.
    1. Remove the transaxle converter cover.
  3. For 1986-90 vehicles, remove the starter motor from the vehicle, as outlined in Section 2.
  4. Remove the oil filter.
  5. If equipped, disconnect the oil level sensor.
  6. For 1996-99 vehicles, remove the oil level sensor. On these vehicles, the oil level sensor must be removed prior to removing the pan. If the pan is removed first, damage to the sensor may occur.
  7. Remove the oil pan-to-engine bolts and the oil pan. Remove and discard the oil pan gasket. The formed rubber oil pan gasket cannot be reused.
  8. If necessary, remove the oil pump pipe and screen.
  9. Thoroughly clean the gasket mounting surfaces.
To install:
  1. If removed, install the oil pump pipe and screen. Secure with the retaining bolt(s) and tighten to 89 inch lbs. (10 Nm).
  2. Place a new formed rubber gasket in the oil pan flange.
  3. Position the oil pan and secure with the oil pan-to-engine bolts. Tighten the bolts to 124 inch lbs. (14 Nm). Do NOT overtighten the bolts, as this will damage the oil pan, causing a leak.
  4. For 1986-90 vehicles, install the starter motor and transaxle converter cover.
  5. Install a new oil filter.
  6. For 1996-99 vehicles, install the oil level sensor.
  7. If equipped, connect the low oil level sensor wire.
  8. Carefully lower the vehicle.

WARNING Operating the engine without the proper amount and type of engine oil will result in severe engine damage.


  1. Fill the crankcase with the proper type and amount of engine oil.
  2. Connect the negative battery cable, then start the engine and check for leaks. Check the oil level and add if necessary.

Oct 05, 2009 | 1991 Buick LeSabre

1 Answer

Replace oil pan gasket 2002 chrysler 300m


The owner of the car should be able to locate and replace oil pan gasket .prepare the equipment to be used .Drain the oil from the oil pan ,spill it to an empty big can that can carry the oil from the oil pan.Then twist the bolts that connect the oil pan to the engine.After removing the bolts then you have take the old gasket off to the oil pan.After taking off the old gasket then you have to replace it with the new oil pan gasket.then return the oil pan with the new gasket. twist the bolt back until the oil pan that connect the oil pan with the engine.And return the drain plug twist until it will not spill.

Sep 30, 2009 | 2001 Chrysler 300M

1 Answer

Re: 2002 Jag X-Type with oil leak


no you should not have to remove the transfer case to remove the oil pan the sump is the oil pump and the oil pan

Jan 01, 2009 | 2002 Jaguar X-Type

1 Answer

2002 Jaguar X-Type Oil Pan Gasket replacement


have you smashed the sump ??never seen one leak yet?? sure its not the front or rear end oil seals ??..sounds like you have the sub frame in the way ,evan if you remove this bolt you will not be able to drop the sump without removing or lowering the sub frame assembly as the oil pick up pipe stops you from removing the sump in situe.Its not difficult to drop sub frame just time consuming

Jan 01, 2009 | 2002 Jaguar X-Type

Not finding what you are looking for?
2002 Jaguar X-Type Logo

Related Topics:

342 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Raygin
Raygin

Level 2 Expert

322 Answers

yadayada
yadayada

Level 3 Expert

61168 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...