Question about 1995 GMC Sierra C1500

1 Answer

Insalling alternator installing an anternator

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 32 Answers

Disconect the negative on the battery and all wires to the alternator. then loosen the drive belt toget it off the alternator pulley. then remove the mounting bolts from the alternator. reverse proceedure for instalation.

Posted on Oct 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Battery losing charge...E430


its possible that the coils of the anternator are worn out.
then the batterie dont charge.take voltmeter and see if the engine,
is running ,if you read some 14.50 volts on the batterie is good.
if you read 12 or 13 volts is bad the anternator

Apr 22, 2013 | Cars & Trucks

1 Answer

I own a 1954 Pontiac that currently has the original generator and 3 contact external regulator. I want to convert to an alternator. I need an old school expert to explain how to wire up the anternator.


We usd to rebuild alternators and we would build some of the old style 10SI Delcos with a self-exciting regulator just for this type situation. All you have to do is connect the battery wire to the stud on the alternator and you were good to go. If you can't find anything local Google "1 wire delco alternator" and you'll come up with all kinds of places to buy them. If you want a regular 3 wire they are easy to wire also. You'll need to buy a regulator plug. The regulator terminals are labeled #1 and #2. #1 is wire to a switched ignition source and #2 can be connected to the battery stud on the alternator along with the battery wire.

Apr 17, 2011 | Pontiac Catalina Cars & Trucks

1 Answer

How to insall engine with manual transmision. do I insall the engine with the bellhousing atatched to the engine or the transmision


If you have removed the Radiator and cleared enough of the forward area to be able to have clearance put the engine back in with the transmission attached. If it looks like you won't have the clearance then attach the bell housing to the Transmission as you should have more room to work with the Bell housing this way although I prefer to install and remove standard mounted engines as assemblies attached to the transmission.

Sep 23, 2010 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

How to install a head unit in a chrysler imperial


Check around, various stereo shops have "Insallation Kits" They come with all you need, and instructions on how to install

Jun 04, 2010 | 1991 Chrysler Imperial

1 Answer

Changing alternator


take the top air filter housing and the tube off, the tensioner will have a small square hole, insert a 3/8" ratchet and push down, that will relieve the tension. ck the tensioner and if it doesnt rotoate smoothly, or there movement front to rear, replace it.

Oct 19, 2009 | 1999 Chevrolet Tahoe

2 Answers

Where can I get the right hand side door glass, how much would it cost? any anternatives possible VJ


well you can get one used if you are worried on coast go to car-parts.com it will ask you some question just put info and zip code or call your local car class shop they can get them in the same day most of the time

Sep 29, 2009 | 1983 Honda Civic

1 Answer

Insalled new computer,cranks but wont start


Does it start and die after 1-2 seconds or just cranks and never fires? Did it run before you installed the computer or are you trying to cure a no start problem?

Jul 12, 2009 | 1999 Chevrolet S-10 Pickup

1 Answer

Equinox drive belt replacement


ok here we go first locate the drive belt tensioner, it should a h spot where you can insert a 1/2 drive breaker bar,release the tension and remove the belt, make you have the diagram that shows how it is insalled(usually on the sticker in the engine compartment) re-install the belt starting from the bottom and working up towards the top.again release the pressure on the tensioner and finish insalling the belt.make sure the beelt is all the way on every pulley. please rate my fix, if you need more help get back to me as i strive to be the best. good luck,let me know how you make out. should not be that hard to do

Apr 27, 2009 | 2005 Chevrolet Equinox

Not finding what you are looking for?
1995 GMC Sierra C1500 Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...