Question about 1992 Plymouth Sundance

Open Question

1992 plymouth Sundance

Having the same problem with 92 sundance. Only mine is really rough and wont seem to stop. no power at all it will idle somewhat better in park or neutral but as soon as put in a forward gear or reverse it chugs and blows smoke. it has quite a few miles so!

I put new plugs in to no avail,also did a check on codes only thing that came up was fan relay switch open. a bunch of sensors it could be i guess one other thing it happend on mine day after getting gas in it?

Posted by on

6 Suggested Answers

  • 2 Answers

SOURCE: 1991 plymouth sundance

WHO SAID IT'S NOT ESSENTIAL....********, MAYBE YOU OUGHT TO LIVE IN GALVESTON OR HOUSTON RIGHT NOW EVEN GETTING GAS

Posted on Sep 16, 2008

  • 132 Answers

SOURCE: 1994 Plymouth Sundance reverse lights

first check bulbs and fuses if no success the reverse light switch is located on gearbox sometimes wires come off and other times faulty and need replacing a test lamp on the switch will help to tell you whether or not power is coming out when in reverse to make the lights work

Posted on Nov 09, 2008

  • 92 Answers

SOURCE: 1992 Plymouth Sundance 2.2

the wire is feed by the asd relay as commanded by the computer to supply power upon seeing cranking rpm. the wire also feeds the injectors and other sensors. the wire you need is in a harnes that runs from the drivers side to the passenger side just behind the back of the valve cover.
good luck chris

Posted on Mar 15, 2009

emissionwiz
  • 61168 Answers

SOURCE: i need all the engine diagnostic codes for a 94

11 Timing belt2.gif skipped 1 tooth or more from initial learned value, Intermittent loss of either camshaft or crankshaft position sensor, No crank reference signal detected during engine cranking
12 Direct battery input to PCM/ECM was disconnected within the last 50 key-on cycles (normal)
13 No change in MAP from start to run
14 MAP sensor voltage too low
15 No vehicle speed sensor signal
17 Closed loop temp not reached or engine cold too long
21 02s sensor problem (oxygen sensor), upstream or down stream
22 Engine coolant temp sensor out of range
23 Intake air temp sensor out of range
24 Throttle Position sensor out of range
25 Idle air control motor circuits, target idle not reached (+/- 200),vacuum leak found
27 Injector control circuit
31 Evap purge flow monitor failure or evap solenoid circuit
32 EGR system failure
33 A/C clutch relay circuit
34 Speed control Solenoid circuits
35 Rad Fan control relay circuit
37 Torque converter clutch solenoid CKT or park/neutral switch failure
41 Generator field not switching properly
42 Fuel pump relay control ckt, Auto shutdown relay control ckt, No ASD relay output voltage at PCM, Fuel level sending unit volts out of range, Fuel level unit No change over miles
43 Multiple/ single cylinder misfire
44 Battery temp sensor volts out of range
46 Charging system voltage too low
51 Fuel system lean
52 Fuel system rich
53 Internal control failure
54 No Cam signal at PCM
55 End of error messages (If you get this only, no errors were found)
62 PCM failure SRI mile not stored
63 PCM Failure EEPROM write denied
64 Catalytic Converter Efficiency Failure
65 Power steering switch failur

Posted on Aug 08, 2009

intallekt
  • 5 Answers

SOURCE: diagram for an alternator belt for 92 plymouth sundance

7dc2762.gif Unsure what engine or Vin Number is for your Car. All 0f the diagrams looked the same for the 2.2 - 2.5 and others, with and with out turbo.
Hope this helps, - Jarett

Posted on Aug 17, 2009

canbruce75
  • 1776 Answers

SOURCE: I need a shop manual for a 1993 plymouth sundance

If you visit the autozone.com website and register your car information, it will give you access to an online repair manual for the car. It is a really handy resource for automotive maintenance that I think you will find helpful. It's free of charge. Hope this helped and best wishes.

Posted on Oct 07, 2009

Testimonial: "Very helpful, thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

92 plymouth sundance. loud pop on drivers side when turning. steering wheel won't turn when brake is pressed.


thats your axle its bad or you call it cvc joint needs to be replace it cost about $150

Apr 26, 2012 | 1992 Plymouth Sundance

1 Answer

Car stalls out at stops


92 sundance isnt "carbuerated", unless you had it carb'd. They have what is called throttle body injection. and your problem could be something as simple as just needing a tune up!

Feb 27, 2012 | 1992 Plymouth Sundance

1 Answer

My check engine light flashes 35 times on a 92 plmouth sundance i was wondering if u would tell me what thats for


That should be radiator fan relay, open or shorted. If your radiator fan is working as it should, the code may have been stored before rad fan was fixed.

Jun 01, 2011 | 1992 Plymouth Sundance

1 Answer

Diagram for an alternator belt for 92 plymouth sundance


7dc2762.gif Unsure what engine or Vin Number is for your Car. All 0f the diagrams looked the same for the 2.2 - 2.5 and others, with and with out turbo.
Hope this helps, - Jarett

Aug 17, 2009 | 1992 Plymouth Sundance

1 Answer

Stall as soon as oil light came on..92 sundance


I don't think a 92 sundance will shut the fuel pump down when the oil pressure is low, but it might. Can you get it to run on carb cleaner. If it is oil pressure, the car should start then run a few seconds and die. Have you checked the timing belt? If it broke the distributor will stop turning which would stop the oil pump.

Jun 05, 2009 | 1992 Plymouth Sundance

1 Answer

No power at take off


Check all your vacum lines and make sure that your plug wires are properly secured this seems like a minor problem

Apr 17, 2009 | 1992 Plymouth Sundance

1 Answer

Sundance leaks gas when it's running


check you r gas lines from tank to motor,fix leak 1st ,if it still idles high let us know

Dec 14, 2008 | 1994 Plymouth Sundance

1 Answer

92 sundance gas gauge doesnt work


IT SOUNDS LIKE YOU NEED TO REPLACE THE FUEL SENDING UNIT. IT SHOULD BE LOCATED ON THE FUEL PUMP.

Dec 14, 2008 | 1992 Plymouth Sundance

1 Answer

Digram on replacing heater core


i have a manual with step by step instructions,no diagram but helpful.
if you still need it i can scan it and email it to you

Oct 16, 2008 | 1992 Plymouth Sundance

Not finding what you are looking for?
1992 Plymouth Sundance Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...