Question about 1999 Ford Taurus
How to repair lower ball joints
The front lower ball joints are pressed into the steering knuckle. Once the brake components are removed, the CV shaft nut and tie rod ends can be removed. Remove the front strut bolts, and the lower ball joint nut. Separate the lower arm from the ball joint. Once the knuckle assembly is off the car remove the lower joint snap ring and dust boot. Utilizing a ball joint press (should be able to rent from local parts store) press the joint out of the knuckle. Re-installation is naturally reverse of removal. I hope this helps.
Posted on Nov 22, 2008
Take your car to the workshop, afterwards pay the bill
Posted on Sep 24, 2008
SOURCE: upper and lower ball joints
Your better off have it done bt a tech because you need a press to press them out and in. Also you will have a warranty witk the work. You want to be safe messing with your steering and suspension. I hope this helps.
Posted on Dec 05, 2008
SOURCE: lower ball joint removal how to
Posted on Sep 12, 2008
Approx.$250 in parts & rest is labor. Probably 3 to 4 hrs labor at most, even at 5 hrs labor, that's $100/hr labor. It must include alignment after the repairs, correct? Not sure what your going rate for labor is in your area. Probably wouldn't hurt to call around for a second opinion& estimate just to be sure.
Posted on Dec 21, 2008
its easier to get the whole control arm and the lower one has to be pressed in. it is not and easy job if you dont have the right tools checkout rockauto.com to look at the replacement parts and to get a price on them
Posted on Mar 31, 2009
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Dec 06, 2015 | Dodge Cars & Trucks
Oct 15, 2014 | 2002 Buick LeSabre
Oct 05, 2012 | Cars & Trucks
Jan 31, 2012 | 1991 Mercedes-Benz 420
Jan 22, 2012 | 2001 Ford Expedition
Jan 17, 2012 | 1997 Chevrolet Lumina
To perform the following procedure, the lower control arm must be removed from the vehicle. Refer to Removal And Installation for that procedure.
NOTE: When installing ball joint in lower control arm, position the ball joint in control arm so notch in ball joint stud is in the direction shown. This will ease assembly of the ball joint to the steering when installing pinch bolt.
CAUTION: Do not use an arbor press to install the sealing boot on the ball joint. Damage to the sealing boot will occur if excessive pressure is applied to the sealing boot when it is being installed.
CAUTION: A replacement ball joint is not pre-lubricated. Properly lubricate the replacement ball joint using Mopar Multi-Mile grease or an equivalent. Lubricate ball joint after seal boot is installed but prior to top of seal boot being pushed down below notch in ball joint stud. Air must vent out of the seal boot at notch when grease is pumped into ball joint, failure to do so will balloon and damage seal boot. Do not over grease the ball joint, this will prevent the seal boot from pushing down on the stud of the ball joint.
CAUTION: After the ball joint is properly greased, clip the end of the grease fleeing off below the hex. The ball joint seal boot is non-purgeable and further greasing is not required and can result in damage to the seal boot.
Mar 07, 2011 | 2000 Dodge Caravan
Dec 05, 2010 | 1997 Dodge Stratus
Nov 28, 2010 | 1994 Pontiac Grand Prix
Jan 07, 2009 | 2001 Mazda B-Series
2,362 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: