Question about 1986 Ford Ranger 2WD

1 Answer

Timing Belt How do you install the timing belt and calibrate it?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 702 Answers

I'll give you detailed instructions tomorrow. It's late right now and I have to get up early. It'll be a lengthy step by step instructions on how to replace the timing belt.

Posted on Sep 26, 2008

  • Lee Quiroz
    Lee Quiroz Sep 27, 2008

    Hi again. remove the upper timing cover. You should see a notch on the upper timing cover, an arrow. Line that up with the middle notch on the 5 o clock position of the inner timing cover. Remove the balancer at the bottom and line the mark on the inner part of the lower timing belt sprocket with the mark on the block. Line the middle sprocket notch with the mark on the block as well. To release the timing belt tensioner, loosen the bolt in the middle and use a pry bar and shift it over and tighten the bolt back up. This will hold the tensioner back while you replace the belt. Install the belt but move the upper sprocket slightly clockwise and install the belt. Pull back the upper sprocket to take up the slack and release the tensioner bolt. I like to use a pry bar and push on the tensioner so the belt is good and tight then tighten the tensioner bolt again. Rotate the engine by using the lower bolt at the center of the balancer twice clockwise, once counter-clockwise and make sure your marks are all in the correct spots. If they are, put everything back together and down the road you go.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need instructions to replace timing belt on a 1995 diesel ford courier


Hi,
REMOVAL
Disconnect the negative battery cable.
Remove accessory drive belt.
Remove the timing belt cover.
Align the timing mark on the camshaft sprocket with the timing mark on the cylinder head.
Confirm that the timing mark on the crankshaft sprocket is aligned with the timing mark on the oil pump housing.
Loosen the belt tensioner attaching bolt.
Pry the tensioner away from the timing belt and tighten the attaching bolt.
Remove the spark plugs.
Remove the RH engine mount and raise the vehicle.
Remove the splash shield.
Remove the crankshaft damper.
Remove the timing belt.

6_13_2012_3_43_16_pm.gif



INSTALLATION


Note: Do not mix 1/2 round and trapazoidal belt tooth profiles. This can cause premature belt wear, also the belt is meant to run in a dry environment. For maximum belt life, no oil or belt dressing compound should be applied to the timing belt.
Install the timing belt over the sprockets in a counterclockwise direction starting at the crankshaft. Keep the belt span from the crankshaft to the camshaft tight while installing over the remaining sprocket.
Loosen the belt tensioner attaching bolt, allowing the tensioner to snap against the belt.
CAUTION: Do not rotate crankshaft with the spark plugs installed .


Note: Do not turn the engine counterclockwise to line up the timing marks. After rotation, recheck camshaft timing marks for alignment. This will verify that the belt has not skipped a tooth during rotation.
Rotate the crankshaft clockwise two complete revolutions (720 degrees) stopping at top dead center. This will allow the tensioner spring to load the timing belt.
Tighten the belt tensioner attaching bolt to 23-30 Nm (17-22 lb-ft) .
Install the crankshaft damper.
Install the splash shield.
Lower the vehicle.
Install the RH engine mount.
Install the spark plugs.
Install the timing belt cover.
Install the accessory drive belt automatic tensioner.
Install the accessory drive belt.
Connect the negative battery cable.


Thank you.

Jun 13, 2012 | Ford Ranger Cars & Trucks

1 Answer

99 kia sporage timing marks


Hi there:



Check this information...

dfd3ea1.gif


Crankshaft match marks


Align marks on timing belt pulley and pump body.

Camshaft pulley alignment marks
9f1c7ef.gif



  1. Align marks on camshaft pulleys with alignment marks on seal plate.
  2. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
  3. Loosen tensioner lock bolt.
  4. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
  5. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
  6. Apply a force of 22 lbs to timing belt between camshaft sprockets.
  7. Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)


  1. NOTE: Replace tensioner spring if timing belt deflection is excessive.
  2. Timing Belt Installation


eb770f2.gif

  1. Install lower timing belt cover.
  2. Install upper timing belt cover.
  3. Install power steering drive belt and adjust belt tension.
  4. Install fan pulley.
  5. Install generator drive belt and adjust belt tension.
  6. Install A/C drive belt and adjust belt tension.
  7. Install splash guard.
  8. Install fan and fan shroud.
  9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
  10. Install fan shroud mounting bolts.
  11. Install fresh air duct.
  12. Connect hose to resonance chamber.
  13. Connect battery negative cable.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.


Thank you for using FixYa, have a nice day.

Mar 14, 2012 | Kia Sportage Cars & Trucks

1 Answer

Problem with 99 kia


Hi there:Check this information...

dfd3ea1.gif


Crankshaft match marks


Align marks on timing belt pulley and pump body.

Camshaft pulley alignment marks
9f1c7ef.gif



  1. Align marks on camshaft pulleys with alignment marks on seal plate.
  2. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
  3. Loosen tensioner lock bolt.
  4. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
  5. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
  6. Apply a force of 22 lbs to timing belt between camshaft sprockets.
  7. Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)


  1. NOTE: Replace tensioner spring if timing belt deflection is excessive.
  2. Timing Belt Installation


eb770f2.gif

  1. Install lower timing belt cover.
  2. Install upper timing belt cover.
  3. Install power steering drive belt and adjust belt tension.
  4. Install fan pulley.
  5. Install generator drive belt and adjust belt tension.
  6. Install A/C drive belt and adjust belt tension.
  7. Install splash guard.
  8. Install fan and fan shroud.
  9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
  10. Install fan shroud mounting bolts.
  11. Install fresh air duct.
  12. Connect hose to resonance chamber.
  13. Connect battery negative cable.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.


Thank you for using FixYa, have a nice day.

Mar 14, 2012 | Kia Sportage Cars & Trucks

1 Answer

How do i set the timing belt on a 1997 cadillac catera?the betl did not break but how do i make sure the belt did not move a couple of teeth.


Hi, there should be marks on the belt itslf that align with hatch marks on the timing gears. Below are the instructions for installation. From these, you should be able to verify that the belt is in time. There are also some diagrams here: http://www.2carpros.com/diagrams/cadillac/catera/1997


To install:
  1. Install the timing belt.
    1. Start at the crankshaft pulley.
    2. Install the timing belt with a double dash (TDC) mark on the belt aligned with the marks on the oil pump and belt drive gear.
    3. Pinch the belt with special tool J 42069-30 to prevent the splines from jumping.

  2. Route the timing belt through the idler pulley for camshafts 3 & 4 then route the timing belt through the camshaft gears 3 & 4.
    1. Ensure the dash marks on the timing belt align with marks on the camshaft gears and the notches on the rear timing belt cover.
    2. If necessary, loosen timing belt idler pulley or move the cam gears slightly, with J 42069-1 and 2 still in place, until the timing belt can be installed.
    3. Tighten the idler pulley locking bolt until snug. The idler pulley bolt will be tightened to specifications after the final adjustments are made.




NOTE Timing belt deflection between the camshaft gears number 4 and the idler pulley for camshafts 3 & 4, must be no more than 0.4 inch (1 CM.).

  1. If necessary, adjust the timing belt deflection by turning the timing bolt idler pulley eccentric, for camshafts 3 & 4, counter-clockwise with the special tool J 42069-40, or equivalent.

  1. Route the timing belt through the timing belt idler pulley for camshafts 1 & 2 then route the timing belt through camshaft gears 1 & 2.
    1. Ensure the dash marks on the timing belt align with the marks on the camshaft gears and the notches on the rear timing belt cover.
    2. If necessary, loosen the timing belt idler pulley or move the cam gear slightly, with J 42069-1 and 2 still in place, until the timing belt can be installed.
    3. Apply sufficient tension to the timing belt to prevent it from slipping off the gears by turning the timing belt idler pulley eccentric for camshafts 1 & 2 counter-clockwise with special tool J 42069-40 or equivalent.
    4. Tighten the idler pulley locking bolt until snug. Idler pulley bolt will be tightened to specifications after final adjustments are made.

  2. Route the timing belt through the timing belt tensioner.
  3. Apply initial tension to the timing belt by turning tensioner eccentric counter-clockwise, with a 5 mm hex wrench, until marks are set.
    1. Tighten the belt tensioner-locking nut to 15 ft. lbs. (20 Nm).

  4. Adjust the timing belt.
    1. The timing belt must be properly adjusted or engine damage may occur. Do not continue with the engine assembly procedure until the timing belt is properly adjusted.

  5. Install the timing belt cover. Tighten the timing belt cover bolts to 71 inch lbs. (8 Nm).
  6. Install the power steering pump pulley and bolts. Install the water pump pulley and bolts.
    1. Tighten the power steering pump pulley bolts and the water pump pulley bolts after the serpentine drive belt is installed.

Mar 04, 2011 | 1997 Cadillac Catera

1 Answer

WHAT IS CORRECT TIMING MARKS FOR TIMING BELT INSTALLATION. 2000 NUBIRA 2.0 DOHC AND CRNKSHAFT MARKS. Thanks Joe


TIMING BELT
Removal
Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing.
Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt.
Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle.
Support engine assembly from above with Support Fixture (J-28467-B). Remove engine mount bracket from timing belt end of engine.Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine).
Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 .
CAUTION: Engine damage could result if camshaft sprockets are not properly aligned with notches on valve cover.
Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. Remove timing belt.
Fig. 4: Aligning Crankshaft Sprocket Timing Mark
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim_4.jpg
Fig. 5: Aligning Camshaft Sprocket Timing Marks
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim2_3.jpg
Installation
Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS .
Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch.
If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt.
Install right front splash shield. Install right front wheel. Install air filter housing and resonator. Connect air intake temperature sensor connector. Connect negative battery cable.
Fig. 7: Identifying Timing Belt Routing
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim3_1.jpg
here

http://www.2carpros.com/questions/daewoo-leganza-2000-daewoo-leganza-timing-marks

Feb 17, 2011 | 2000 Daewoo Nubira

1 Answer

Como poner la banda de tienpo de un toyota camery


Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence.

Dec 23, 2010 | 1993 Toyota Camry V6

2 Answers

Need diagram to put timingbelt on 2001 kia sportage


prev.gif next.gif Timing Belt Removal & Installation SOHC To Remove:
  1. Disconnect battery negative cable.
  2. Remove fresh air duct.
  3. Drain engine coolant into an appropriate container and retighten radiator drain plug.
  4. Remove upper radiator hose.
  5. Remove fan clutch assembly bolts.
  6. Remove 5 cooling fan shroud bolts.
  7. Remove fan shroud and fan as an assembly.
  8. Loosen alternator mounting bolts and remove drive belt from pulley.
  9. Remove fan pulley.
  10. Remove 4 cooling fan assembly bolts.
  11. Remove cooling fan assembly.
  12. Remove 4 bolts and upper timing belt cover.
  13. Remove 2 lower bolts and lower timing belt cover.
  14. Loosen adjusting bolt and remove A/C belt.
  15. Remove alternator belt.
  16. Loosen power steering pump lock bolt and mounting bolt.
  17. Remove drive belt from crankshaft damper. Camshaft timing marks kia-03-20-7032.gif

  18. Turn crankshaft until timing mark on front housing and the arrow "2" on the camshaft pulley align.
  19. Remove 5 bolts and remove damper.
  20. Remove timing belt guide from timing belt pulley.
  21. Loosen tensioner lock bolt.
  22. Pry tensioner away from timing belt and tighten lock bolt to relieve tension on the timing belt. NOTE: Mark the direction of timing belt rotation on the belt if it is being reused.
  23. Remove timing belt.
To Install:
Timing belt pulley timing marks kia-03-20-7035.gif

NOTE: Timing belt pulley timing mark and timing mark must be aligned.
Camshaft timing marks kia-03-20-7032.gif

NOTE: The arrow at "2" on camshaft pulley must be aligned with timing mark on front housing.
Timing belt installation kia-03-20-7036.gif

  1. Install timing belt with minimal slack from timing belt pulley to water pump and from water pump to camshaft pulley.
  2. Loosen tensioner lock bolt until tension is applied to timing belt. CAUTION
    Do not turn crankshaft counterclockwise.
  3. Turn crankshaft pulley 2 full turns clockwise and ensure timing marks are properly aligned.
  4. Tighten tensioner lock bolt to 33 ft lb (45 Nm).
  5. Apply a force of 21 lb to timing belt midway between idler pulley and camshaft pulley.
    • Deflection should measure 0.43-0.51 inch (11-13 mm)
    NOTE: if timing belt deflection is incorrect remove timing belt and install NEW tensioner spring.
  6. Install timing belt guide.
  7. Install crankshaft damper pulley.
  8. Install 5 crankshaft damper pulley bolts. Tighten bolts to 132 in lb (15 Nm).
  9. Install power steering pump drive belt.
  10. Adjust power steering pump drive belt tension and tighten lock bolt and mounting bolt.
  11. Install alternator drive belt.
  12. Install A/C drive belt.
  13. Install lower timing belt cover and bolts. Tighten bolts to 84 in lb (10 Nm).
  14. Install upper timing belt cover and bolts. Tighten bolts to 84 in lb (10 Nm).
  15. Install cooling fan assembly and 4 bolts. Tighten bolts to 27 ft lb (37 Nm).
  16. Install fan pulley.
  17. Install fan clutch and shroud as an assembly. Tighten bolts to 74 in lb (8 Nm).
  18. Tighten 4 cooling fan nuts to 16 ft lb (22 Nm).
  19. Adjust alternator belt tension and tighten alternator mounting bolts.
  20. Install upper radiator hose.
  21. Install fresh air duct.
  22. Connect battery negative cable.
  23. Refill/bleed cooling system.
DOHC To Remove:
  1. Disconnect battery negative cable.
  2. Remove fresh air duct.
  3. Remove 5 cooling fan shroud bolts and 4 thermo-modulated fan nuts.
  4. Remove 4 thermo-modulated fan shroud fasteners.
  5. Remove generator drive belt.
  6. Remove fan pulley (located above crankshaft pulley).
  7. Remove 4 bolts and splash shield (located under front of vehicle).
  8. Remove A/C drive belt and power steering drive belt. Timing Belt Removal kia-03-20-7097.gif

  9. Remove 5 bolts and upper timing belt cover.
  10. Remove 2 bolts and lower timing belt cover.
  11. Loosen tensioner lock bolt and pivot tensioner pulley outboard.
  12. Retighten tensioner lock bolt. NOTE: Mark timing belt for rotation if it is being reused.
  13. Remove timing belt.
To Install:
Crankshaft match marks 79245g25.gif

  1. Align marks on timing belt pulley and pump body. Camshaft pulley alignment marks 79245g28.gif

  2. Align marks on camshaft pulleys with alignment marks on seal plate.
  3. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
  4. Loosen tensioner lock bolt.
  5. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
  6. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
  7. Apply a force of 22 lbs to timing belt between camshaft sprockets.
    • Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)
    NOTE: Replace tensioner spring if timing belt deflection is excessive.
    Timing Belt Installation kia-03-20-7097.gif

  8. Install lower timing belt cover.
  9. Install upper timing belt cover.
  10. Install power steering drive belt and adjust belt tension.
  11. Install fan pulley.
  12. Install generator drive belt and adjust belt tension.
  13. Install A/C drive belt and adjust belt tension.
  14. Install splash guard.
  15. Install fan and fan shroud.
  16. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
  17. Install fan shroud mounting bolts.
  18. Install fresh air duct.
  19. Connect hose to resonance chamber.
  20. Connect battery negative cable.

Aug 02, 2010 | 2001 Kia Sportage

2 Answers

I need 2004 Hyundai XG350L Service/repair Manual


3.5L Engine

Remove or disconnect the following:
  1. Negative battery cable
  • Engine coolant
  • Water pump pulley bolts
  • Alternator bolt, loosen only
  • Water pump pulley and drive belts
  • Crankshaft pulley
  • Timing belt cover(s)
  1. Turn the crankshaft until the timing marks on the camshaft sprocket and cylinder head are aligned.
  2. Loosen the timing belt tensioner bolt and turn the tensioner counterclockwise as far as it will go. Tighten the adjusting bolt.
  3. Mark the timing belt with an arrow showing direction of rotation.
  4. Remove the timing belt.
  5. If defective, remove the timing belt tensioner.

9767b45.gif
Timing belt sprocket alignment mark positioning for belt removal and installation—3.5L engine

To install:
  1. If necessary, install the timing belt tensioner.
  2. Attach the top of the tensioner spring on the engine coolant pump pin. Ensure the hook on the pin is facing down and the hook on the tensioner is facing away from the engine
  3. Rotate the timing belt tensioner to the extreme counterclockwise position. Temporarily lock the tensioner in place.
  4. Align the timing marks of the camshaft and crankshaft sprockets.
  5. Install the timing belt on the crankshaft sprocket, then onto the rear camshaft sprocket.
  6. Route the belt to the coolant pump pulley, the front camshaft sprocket and the timing belt tensioner.
  7. Apply force counterclockwise to the rear camshaft sprocket with tension on the tight side of the belt and check that timing marks are aligned.
  8. Loosen the tensioner bolt 1–2 turns and tighten the timing belt to a tension of 57–84 lbs. (260–380 N).
  9. Turn the crankshaft two turns clockwise.
  10. Readjust the sprocket timing marks and tighten the tensioner bolts.
  11. Install the timing belt covers.
  12. Install the crankshaft pulley and tighten to 108–116 ft. lbs. (150–160 Nm).
  13. Install or connect the following:
    • Timing belt cover(s)
    • Crankshaft pulley
    • A/C compressor belt
    • Water pump pulley
    • V belt
    • Negative battery cable
    • Engine with coolant

Feb 10, 2010 | 2004 Hyundai XG350

3 Answers

1999 kia sportage timing marks


dfd3ea1.gif Crankshaft match marks


Align marks on timing belt pulley and pump body.

Camshaft pulley alignment marks
9f1c7ef.gif
  1. Align marks on camshaft pulleys with alignment marks on seal plate.
  2. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
  3. Loosen tensioner lock bolt.
  4. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
  5. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
  6. Apply a force of 22 lbs to timing belt between camshaft sprockets.
  7. Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)
  8. NOTE: Replace tensioner spring if timing belt deflection is excessive.
Timing Belt Installation


eb770f2.gif
  1. Install lower timing belt cover.
  2. Install upper timing belt cover.
  3. Install power steering drive belt and adjust belt tension.
  4. Install fan pulley.
  5. Install generator drive belt and adjust belt tension.
  6. Install A/C drive belt and adjust belt tension.
  7. Install splash guard.
  8. Install fan and fan shroud.
  9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
  10. Install fan shroud mounting bolts.
  11. Install fresh air duct.
  12. Connect hose to resonance chamber.
  13. Connect battery negative cable.

Jul 26, 2009 | 1999 Kia Sportage

2 Answers

Need instructions to replace 1993 Toyota Camry Timing Belt


Hi Kmcarroll77

TIMING BELT REPLACEMENT - 2.2L -1993 Toyota Camry

Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence. See Fig. 6 . On MR2, tighten engine
b7619be.jpg
92cabaf.jpg
Hope this helps, don't forget to rate.

Lazaruselite

Feb 25, 2009 | 1993 Toyota Camry V6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

190 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...