Question about 1993 Mitsubishi Mirage

1 Answer

No sparks from ignition coil

Bought a brand new distributor,but still no electricity coming out from ignition coil, i put screwdriver inside it and hold the metal parts while my friend starts the engine,but still no high voltage coming out..fusible links are all ok....there is a 12 volts to distributor socket...please send some advice..

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

Ignition rotor

Posted on Sep 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is there no spark from spark plug 1995 k1500 silveraldo


1995 silverado has a distributor, remove the the distributor cap, make sure the distributor spins with the engine. also make sure the ignition rotor is not burned out or have a hole were it makes contact with the cap. also make sure the cap has a good carbon inside to make contact with the rotor, at this time get a screw driver, put it on the end of the wire from the coil to the cap, don't touch the metal part of the screwdriver, it will shock you if good, so put it at 5/16 from any metal on the engine, bracket, alternator , thermostat housing no matter, some one turns the engine over, check to see if the coil produces a spark, if the rotor turns, if ok it should have spark on all the wires, if it has no spark, remove the wire from the ignition coil and check if you have spak at the coil, if you have no spark, try getting a wire lead, connect it from the battery ground on one end, a screw driver on the coil to check for spark, and the other end of the wire with the key on, touch the - negative plug on the coil, that should produce a spark, if not spark yet, make sure you do have power at the coil with key on, if you do and it doesn't produce spark, replace coil. if it does spark but it is weak or yellow in color, replace coil. if coil is fine, replace distributor module,

Jul 10, 2014 | 1995 Chevrolet K1500

2 Answers

It turns but it wont start,it has gas and power


Pull off the coil ignition cable at the distributor and check for spark coming out of coil when cranking engine over. Use a heavy rag or glove to hold the wire 1/4 inch from a metal ground. Should see a strong blue spark when cranking to verify ignition is good. If no spark, check for battery voltage to coil on the coil primary. If you have current to the coil, suspect a bad coil, ignition module, crank position sensor, or cam position sensor, or pcm. The coil, ignition module, and sensors can be tested before replacing.

Jan 29, 2013 | Cars & Trucks

1 Answer

I got no spark coming out of a good ignition coil


The pickup coil - stator in the bottom of the distributor sends a signal to the igniter, which grounds the coil.
You may need a shop manual to be able to test the distributor and the igniter.

Sep 12, 2012 | 1992 Toyota Camry V6

1 Answer

I have a 1994 dodge ram b250 conversion van with a 3.9 v6 and i had to put a timing chain and gears in and now i can get it to fire no spark all it does it whirl over and again no spark from dist. to coil...


check to make sure distributor electrical wires been reconnected to distributor.and check to make sure distributor is receiving 8 volts supply from the pcm.check see if orange wire going to distributor to pcm getting power. because spark plugs not firing could be pcm, coil itself bad or crankshaft sensor bad. i would code scan vechicle before buying new parts ignition.timing off if you did not have distributor in number 1 firing position before removing the timing chain.

Oct 03, 2011 | Dodge Ram B250 Cars & Trucks

1 Answer

The current of number four ignition coil not passing throu to sparkplug


Hi,
If the electricity failed to go in your spark plug #4, the problem would be in the distributor cap and the high tension cable.
Open the distributor cap, check the contact terminal on the number 4, clean it if you seen some white oxidation, and clean also the rotor. Use a metal file or a sand paper to clean those parts.
Check the high tension cable, pull the connection of the cable from the spark plug of # 4, put a screw driver inside the plug and let somebody crank the engine. The screwdriver should be place near a ground, bare metal( about 1/2" away from metal), a spark should be seen coming out from the screw driver going to ground, if not the cable must be replace!

Hope that helps you out!
Thanks for using Fixya!

Dec 17, 2010 | 2004 Mazda 3

1 Answer

Getting spark and fuel and did a tune up and put new injectors in there but the car cranks but wont start and it is 1988 corvette


The ignition module and the pick-up coil/stator located inside of the distributor is what generates the signal that the ECM (Engine Control Module) uses to time and fire the fuel injectors, as well as the signal to run the fuel pump and the dwell signal timing to fire the ignition coil, and a faulty ignition module can cause any one of these systems to malfunction.

That does sound like a malfunction with the ignition module inside of the distributor, and you can remove the ignition module and have it tested for free at most auto part stores.

If you do purchase a new ignition module be sure that it does come with a silicone grease or a die-electric compound because it is a heat sink and the ignition module will burn up without it.

To install the new ignition module first clean out the mounting surface inside of the distributor. Then completely coat the metal contact surface under the ignition module with a thick coat the silicone grease or die-electric compound and do not leave any of the metal contact surface of the ignition module un-coated with the silicone grease or die-electric compound, and be very careful not to over-tighten the ignition module or it will be damaged.

The same principal applies to HEI (High Energy Ignition) ignition systems with the ignition coil mounted in the top of the distributor cap.

Sep 25, 2010 | 1988 Chevrolet Corvette

2 Answers

No spark from spark plug wires I think it may be the distributor cap or interior parts under cap like rotor and condensor but dont want to change parts thats are fine i replaced the plugs but still no...


There wrere two types of HEI (High Energy Ignition) distributors used by GM in 1985, one was the original design with the ignition coil mounted in the top of the distributor cap, and the second had the coil mounted seperate from the distributor and used a coil wire.

There is the possibility that the ignition coil is faulty and first check to see if full battery voltage is even getting to the "Pos" (+) positive side of the ignition coil when the key is in the "Run" position, and also if the coil is seperate from the distributor that full battery voltage is getting through the "Pos" (+) or positive side of the ignition coil and over to the distributor ignition module, dis-connect the wire connector from the ignition module and if battery voltage is not present at the connector to the ignition module with the key in the "Run" position but it is present at the "Pos" side of the ignition coil, then the ignition coil is faulty. If battery voltage is present then check the ohms between the high tension terminal (where the coil wire goes on the ignition coil) and the "Pos" terminal on the ignition coil by first dis-connecting the wires from the ignition coil and then test with the "Neg" lead from the ohm meter in the high tension terminal on the ignition coil, and the "Pos" lead from the ohm meter to the the "Pos" terminal on the ignition coil, and the ohm reading should be between 6,000 and 30,000 ohms and if not replace the ignition coil. A faulty ignition coil can also damage the ignition module.

The ignition module and the pick-up coil/stator located inside of the distributor is what generates the signal that the ECM (Engine Control Module) uses to time and fire the fuel injectors, as well as the signal to run the fuel pump and the dwell signal timing to fire the ignition coil, and a faulty ignition module can cause any one of these systems to malfunction.

That could be a malfunction with the ignition module inside of the distributor, and you can remove the ignition module and have it tested for free at most auto part stores. If the ignition module does test out alright then the problem could still be in the pick-up coil/stator, (it can be tested using an ohm meter by dis-connecting the wire connector from the pick-up coil/stator and the ohm reading between the two wires from the pick-up coil/stator should be between 500 and 1500 ohm's, and both of the wires from the pick-up coil/stator should show an open loop or an infinite reading between each wire and ground) and if the pick-up coil/stator is found to be faulty then replace the entire distributor, or the distributor will have to be dis-assembled to install a new pick-up coil/stator.

If you do purchase a new ignition module be sure that it does come with a silicone grease or a die-electric compound because it is a heat sink and the ignition module will burn up without it.

To install the new ignition module first clean out the mounting surface inside of the distributor. Then completely coat the metal contact surface under the ignition module with a thick coat the silicone grease or die-electric compound and do not leave any of the metal contact surface of the ignition module un-coated with the silicone grease or die-electric compound, and be very careful not to over-tighten the ignition module or it will be damaged.

Let me know if you require any further assistance.


GM HEI Ignition Coil (Mounted In Distributor Cap Type)
264bd9f.jpg

ec2cf30.jpg

Jul 30, 2010 | 1985 Chevrolet Chevy

1 Answer

1979 chevy van not getting spark.was running fine day before.turns over fine,getting fuel.could it be the module


First thing is what condition are the distributor cap, ignition rotor, and spark plug wires in?

There is the possibility that the ignition coil located in the top of the distributor cap is faulty and first check to see if full battery voltage is even getting to the "Bat" or "Pos" (+) positive side of the ignition coil when the key is in the "Run" position. Then check the secondary resistance to the ignition coil.

The ignition module and the pick-up coil/stator located inside of the distributor is what generates the signal that the ECM (Engine Control Module) uses to time and fire the fuel injectors, as well as the signal to run the fuel pump and the dwell signal timing to fire the ignition coil. A faulty ignition module can cause any one of these systems to malfunction.

That does sound like a malfunction with the ignition module inside of the distributor, and you can remove the ignition module and have it tested for free at most auto part stores. If the ignition module does test out alright then the problem could still be in the pick-up coil/stator, (it can be tested using an ohm meter by dis-connecting the wire connector from the pick-up coil/stator and the ohm reading between the two wires from the pick-up coil/stator should be between 500 and 1500 ohm's, and both of the wires from the pick-up coil/stator should show an open loop or an infinite reading between each wire and ground) and if the pick-up coil/stator is found to be faulty then replace the entire distributor, or the distributor will have to be dis-assembled to install a new pick-up coil/stator.

If you do purchase a new ignition module be sure that it does come with a silicone grease or a die-electric compound because it is a heat sink and the ignition module will burn up without it.

To install the new ignition module first clean out the mounting surface inside of the distributor. Then completely coat the metal contact surface under the ignition module with a thick coat the silicone grease or die-electric compound and do not leave any of the metal contact surface of the ignition module un-coated with the silicone grease or die-electric compound, and be very careful not to over-tighten the ignition module or it will be damaged.

Let me know if you require any further assistance.


b0c4aa0.jpg

Jul 29, 2010 | 1979 Chevrolet C/K 3500

1 Answer

What would cause my car to not send spark to the spark plugs


The first thing is do you know when the last time was that the distributor cap, ignition rotor, and spark plug wires were changed?

There is the possibility that the ignition coil is faulty and first check to see if full battery voltage is getting to the "Pos" (+) positive side of the ignition coil when the key is in the "Run" position, and also that full battery voltage is getting through the "Pos" (+) or positive side of the ignition coil and over to the distributor ignition module, dis-connect the wire connector from the ignition module and if battery voltage is not present at the connector to the ignition module with the key in the "Run" position but it is present at the "Pos" side of the ignition coil, then the ignition coil is faulty. If battery voltage is present then check the ohms between the high tension terminal (where the coil wire goes on the ignition coil) and the "Pos" terminal on the ignition coil by first dis-connecting the wires from the ignition coil and then test with the "Neg" lead from the ohm meter in the high tension terminal on the ignition coil, and the "Pos" lead from the ohm meter to the the "Pos" terminal on the ignition coil, and the ohm reading should be between 6,000 and 30,000 ohms and if not replace the ignition coil. A faulty ignition coil can also damage the ignition module.

The ignition module and the pick-up coil/stator located inside of the distributor is what generates the signal that the ECM (Engine Control Module) uses to time and fire the fuel injectors, as well as the signal to run the fuel pump and the dwell signal timing to fire the ignition coil, and a faulty ignition module can cause any one of these systems to malfunction.

That could be a malfunction with the ignition module inside of the distributor, and you can remove the ignition module and have it tested for free at most auto part stores. If the ignition module does test out alright then the problem could still be in the pick-up coil/stator, (it can be tested using an ohm meter by dis-connecting the wire connector from the pick-up coil/stator and the ohm reading between the two wires from the pick-up coil/stator should be between 500 and 1500 ohm's, and both of the wires from the pick-up coil/stator should show an open loop or an infinite reading between each wire and ground) and if the pick-up coil/stator is found to be faulty then replace the entire distributor, or the distributor will have to be dis-assembled to install a new pick-up coil/stator.

If you do purchase a new ignition module be sure that it does come with a silicone grease or a die-electric compound because it is a heat sink and the ignition module will burn up without it.

To install the new ignition module first clean out the mounting surface inside of the distributor. Then completely coat the metal contact surface under the ignition module with a thick coat the silicone grease or die-electric compound and do not leave any of the metal contact surface of the ignition module un-coated with the silicone grease or die-electric compound, and be very careful not to over-tighten the ignition module or it will be damaged.

Let me know if you require a firing order diagram any further assistance with testing or diagnostic procedures.




42d2a26.jpg

c88274e.jpg

Jul 29, 2010 | 1995 Chevrolet Blazer

2 Answers

1992 s10 4.3 motor Sometimes the spark plugs


Ignition module... Most auto parts stores can test these

May 03, 2010 | 1992 Chevrolet S-10

Not finding what you are looking for?
1993 Mitsubishi Mirage Logo

Related Topics:

190 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...