Question about 1999 Jeep Grand Cherokee

1 Answer

On my 2000 grand cherokee the overhead console info center keeps flashing codes for the garage door opener

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My 1999 grand cherokee overheats when idling change themostat still overheats

Posted on Nov 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the security box on 1993 gran cherokee located


Security Alarm Module is located in rigt side box of glove box (attached image) from Repair Manual (Wiring Section).

3_22_2012_12_31_19_pm.jpg

Hope helps.

Mar 22, 2012 | 1993 Jeep Grand Cherokee

1 Answer

I want to program the garage door opener for a 1998 Jeep Grand Cherokee that we just bought. How do I do that?


Depends which kind of garage opener you have. But generally, it goes like this:

In car, press and hold 2 outer buttons on overhead console until indicator lights start flashing.

Hold desired button you want to program garage opener with until lights begin to flash rapidly.

At the garage door receiver in the garage, press the "learn" button. (Mine was located under one of the plastic light covers; it is purple in mine, can be other colors, but should say "learn button" or something similar) If I recall correctly, the light next to the learn button started flashing after I pressed it.

Quickly go back to the car, and press and hold the desired button and the garage should close.

That should be it.

Jul 26, 2011 | 1998 Jeep Grand Cherokee

1 Answer

What fuse is for the power door locks on a 2000 Grand Cherokee Laredo?


Check position F8 15AMP (Lt Blue) for Overhead console, rear wiper, IP lights, rear flipper glass solenoid, POWER LOCKS (click for zoom)...

zjlimited_779.jpg

This is located WJ Junction Block (under dash, left of steering wheel)...

zjlimited_780.jpg

Hope helps (remember to rate this answer).

Mar 03, 2011 | 2000 Jeep Grand Cherokee

1 Answer

The computer in the overhead console of my 2003 Jeep Grand cherokee won't work


This is a very common problem with many of the mid 2000 truck and SUV overhead consoles. The console is very prone to internal failure. I offer a reasonable repair service with a lifetime guarantee, check it out: www.autoclockrepair.com
There is a bunch of useful info there. Drop me an email if you have questions, thanks!

Jun 16, 2010 | 2004 Jeep Grand Cherokee

2 Answers

1995 Jeep grand cherokee limited, 5.2, all time 4x4. I have discovered two 6 pronged connectors under the steering column coming from the same harness, they will connect to each other and the wire colors...


I have a 1995 Jeep Grand Cherokee LTD. I removed the dash to replace the blend door in the HVAC assembly. I got the blend door replaced and when I put it back together the overhead console and the center electronic information center does not work. I have two black connectors I could not remember where they hooked up at and believe this is the reason why the overhead console and electronic information console are not working. Attached are the 2 connectors. I need to know where they connect to under, around, or behind the dash board. E-mail all responses to royaj0131@yahoo.com_1814.jpg_1815.jpg

Jun 12, 2010 | 1995 Jeep Grand Cherokee

1 Answer

How to remove Overhead Console on 2000 Jeep Grand Cherokee, due to menu bottons not working


straight from the Jeep service manual

1.) Disconnect negative battery cable.
2.) Remove screws attaching front of overhead console to front of bracket.
3.) Pull console downward from area near courtesy lights. 4.) Disconnect electrical connectors and remove console from vehicle.

To install, reverse removal procedure.

Apr 10, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Information center not working on 1997 jeep grand cherokee


The information center located on the overhead console gathers information from several sources. If some of those sources are not providing info then the display won't show it. When you say it is not working you need to see first if it is lit or not, or is it that some data (not all) is not showing?

Mar 07, 2010 | 1997 Jeep Grand Cherokee

1 Answer

2002 Jeep Grand Cherokee. The overhead console display works intermitently? It does seem to come on (after switching the ignition off and on again) after the vehicle warms up a few minutes? Any ideas?


This is a very common problem with many of the mid 2000 truck and SUV overhead consoles. The console is very prone to internal failure. I offer a reasonable repair service with a lifetime guarantee, check it out: www.autoclockrepair.com
There is a bunch of useful info there. Drop me an email if you have questions, thanks!

Mar 04, 2010 | 1999 Jeep Cherokee

1 Answer

How do i reprogram the garage door opener on the overhead console


easy.. first hold the 1st & 3rd button above you for like 20-30 secs until the readout flashes.

then.... hold the button of choice along WITH the button of choice on the garage door remote (held within 3" of each other ) until the display flashes fast.

Try to do this away from your house so your garage door opener doesn't freak out with all the button holding.

Problem solved.

Jul 27, 2009 | 2003 Jeep Grand Cherokee

1 Answer

How can i program my garage door to open from my 01 jeep grand ch


Hold down the button on your garage door opener while pushing one of the 3 buttons on the overhead console in the Jeep. It will beep when confirmed.

Jan 05, 2009 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
1999 Jeep Grand Cherokee Logo

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...