Question about 1986 Audi 5000 CS

1 Answer

'86 audi 5000 turbo

Idles OK but when you put it in drive it stalls if you dont go right away. Reverse is OK and it doesnt stall at any speed other than stopped.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

Back of throttle area ducting should be tight or worn collapesed hose causeing vaccum leak

Posted on Sep 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my truck die when I put it in drive


Stalls when put into Drive or Reverse - Ford Truck Enthusiasts Forums

www.ford-trucks.com > ... > 1987 - 1996 F150 & Larger F-Series Trucks
May 22, 2012 - Stalls when put into Drive or Reverse 1987 - 1996 F150 & Larger ... the fluid that was needed...my truck would stall when I shifted into reverse. 1995 Bronco stalls when put into drive
Jun 13, 2013
ford powerstroke truck dies in reverse
Oct 29, 2011
Truck dies when putting in gear and giving it gas.
Feb 26, 2011
ENGINE IDLES FINE,DIES WHEN PUT IN DRIVE
Jun 26, 2010
More results from www.ford-trucks.com

TRUCK DIES WHEN PUT IN REVERS


Nov 30, 2015 | Cars & Trucks

1 Answer

My 1990 nissan 240sx started to just stall out when I come almost to a complete stop and when I put in reverse if i dnt punch on the gas it will stall then it wont start rite away it takes a while then...


Engine stall or RPM fluctuates at idle.

This problem is commonly caused by a dirty automatic idle speed control valve and throttle valve. Buy a can of throttle valve cleaner (do not use carburetor spray cleaner!) from NAPA or Carquest (made by CRC chemicals) and spray it into the air intake while the engine is running, use up about 1/2 the can, engine will try to stall hold the speed up, shut it down and let it soak for 30 minutes, restart and blow out the remaining fluid, shut it down and disconnect the negative battery cable for 5 Min's to reset the base idle control

Sep 13, 2012 | Cars & Trucks

1 Answer

Galant vrg-gdi-when i engage reverse the car stalls--but once you start moving --ok


You vehicle uses a Idle air control motor,(IAC) when you put a load on the vehicle (Drive or reverse) the ECM detects the load and idles up the IAC, even for the A/C (air conditioner) You can try a throttle body cleaning. or a new IAC

Mar 01, 2012 | Cars & Trucks

1 Answer

My A4 turbo keeps stalling smokes & idles erratically


That sounds correct. When the seals/bearings go out in the turbo, oil that is used to cool/lubricate the turbo is force into the engine through the intake. The oil burns, and smokes. Take of the air filter hose from the inducer side of the turbo, (with the car not running), and see if the blade moves at all (shaft play, up, down, in, and out). If you can move it is probably shot. You can also check for oil in the side that leads to the engine. The only other thing would be to check the compression of the engine. The piston rings could be shot.

May 01, 2010 | 2001 Audi A4

1 Answer

My 1994 nissan maxima is stalling when cold. It is sweet when it has been warmed up for a while and ok in park (auto) but when you go to put in gear or reverse it stalls. The trans is also slipping out...


You will ned to get the computer "scanned" to detect what appears to be two separate problems. If the stalling was the only fault I would have said it was either the throttle positon sensor faulty or the Air flow meter / sensor. However the two may be linked. ie faulty speed sensor.

Nov 28, 2009 | 1994 Nissan Maxima

1 Answer

1.car stalls out when you put it in gear, mainly reverse. 2.jerks and stalls when starting forward..A4..1.8T 2002 audi 1.8 turbo L4 FI 20V 112,000 miles


Sounds like your TCC (torque converter clutch) solenoid is causing improper lockup, causing the engine to stall. It works similar to putting your hand on a ceiling fan to stop the blades. I believe this is where you will find your problem.

Good Luck!

Sep 01, 2009 | 2002 Audi A4

1 Answer

Automatic vehicle stalls at low rpm


This is proplem with the IAC valve , try clean the valve and if that doesnt work replace it.

An IAC (idle air control) motor is designed to adjust the engine idle RPM speed by opening and closing an air bypass passage inside the throttle body

Thanks
Kindly rate the answer
Smith

Jul 09, 2009 | 2002 Land Rover Freelander

3 Answers

Idles fine then dies when put in drive or reverse


You may have a problem with idle speed control motor or ETC as GM calles it. here is a photo and a price from rockauto.com.
STANDARD MOTOR PRODUCTS Part # SA4 moreinfo.gif
Motor Assembly sa4_full.jpg $110.99

Apr 18, 2009 | 1990 Cadillac Fleetwood

1 Answer

Mitsubishi libero idling funny!!??


Do you have a check engine light on?

Mar 07, 2009 | 2001 Mercury Cougar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

248 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

13152 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...