Question about 1994 Mitsubishi 3000GT

2 Answers

Tapping noise mitsubishi 3000 GT

How's it going?

My car has got this tapping weird noise when Iturn it on and drive it. it usually takes about 2 to 3 minutes for thenoise to stop

What's wrong?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi my pejero jeep has a tapping noise coming from the tapped which gets louder as im driving ive taken the rocker of but cant see anything out of place

Posted on Sep 04, 2011

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Is it full of oil cause the oil might not be getn around the engine fully when its on a cold start

Posted on Sep 27, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What will be the problem if i have a taping noise when i start my car until it gets warm mitsubishi 380


A tapping noise that starts out cold and goes away when warm is usually caused by a valve lifter inside the engine. The lifter may be worn/leaking down and will be noisy until it fills with oil pressure. You can try an oil additive ( Lucas Oil Additive ) available at most part stores works very well with noisy lifters. Another noise that can happen cold and go away when warm is an exhaust manifold leak. However, this is normally a ticking type sound rather than a tapping sound.

Jan 19, 2016 | Mitsubishi Cars & Trucks

1 Answer

I have a 93 Mitsubishi 3000 gt and when I try to start it it makes a clicking noise .. whats the issue ?


Is the starter making the noise, or the engine ?
Do you have power going to the starter ? Can you turn the engine crank by hand ?

Jun 30, 2013 | Cars & Trucks

1 Answer

Driving on the road the RPM goes higher wituout speedind


Check out related help links to troubleshoot these problem:----Click the link below:---Idles Fine but RPM jumps in drive mode?http://technoanswers.blogspot.in/2012/07/idles-fine-but-rpm-jumps-in-drive-mode.html
---------Mitsubishi Lancer rpm needle bounces?http://technoanswers.blogspot.in/2012/02/mitsubishi-lancer-rpm-needle-bounces.html
--------How to adjust rpm on 2009 dodge charger SRT8?


http://schematicsdiagram.blogspot.com/2011/12/how-to-adjust-rpm-on-2009-dodge-charger.html
---------
Engine cuts out at 3000 RPM?http://schematicsdiagram.blogspot.com/2011/12/engine-cuts-out-at-3000-rpm.html

---------

Cold start problem and vehicle shudder around 2500 to 3500 rpms
http://repairhelpcenter.blogspot.com/2012/10/cold-start-problem-and-vehicle-shudder.html

---------
High rpm in neutral? Inconsistant high RPM in neutral?http://technoanswers.blogspot.in/2012/02/high-rpm-in-neutral-inconsistant-high.html

-----------
Jetski Sputters and Low RPM? http://whatisbyme.blogspot.in/2012/07/jetski-sputters-and-low-rpm.html

--------
Fuel Injection Problem And RPM suddenly increaseshttp://whatisbyme.blogspot.in/2012/07/fuel-injection-problem-and-rpm-suddenly.html

----------
2005 Toyota Highlander: Engine runs hard RPM below 3000?http://whatisbyme.blogspot.in/2012/05/2005-toyota-highlander-engine-runs-hard.html

---------
1987 Toyota Camry: RPM Drops going Up hills?http://whatisbyme.blogspot.in/2012/05/1987-toyota-camry-rpm-drops-going-up.html

-----------
Cruise Control stops working, Excessive cranks to start the engine and RPM goes max 2500 http://whoisbyme.blogspot.in/2012/07/cruise-control-stops-workingexcessive.html

----------
1990 Toyota 4Runner: Engine cuts off when reaches 2000 RPM?


http://whatisbyme.blogspot.in/2012/05/1990-toyota-4runner-engine-cuts-off.html

------------
1999 Toyota Camry: Erratic stalling and high engine RPM at idle?


http://whatisbyme.blogspot.in/2012/05/1999-toyota-camry-erratic-stalling-and.html

---------
1995 Toyota LS: Misfire at idle or low RPMhttp://whatisbyme.blogspot.in/2012/04/1995-toyota-ls-misfire-at-idle-or-low.html

-----------
Lexus RX: Tapping noise under Valve Cover At Low RPM?http://technoanswers.blogspot.in/2012/04/lexus-rx-tapping-noise-under-valve.html

----------
These will help.
Thanks.

Nov 22, 2012 | 2008 Toyota Avalon

1 Answer

I got a saaab 99 9-5 se 2.3l turbo when i step on the gas i get a weird noise like a tapping/whirling noise and stops if i take foot off gas. when in park i have a semi engine tap i cant seem to figure out...


COULD BE WORN TURBO BEARING CAUSING TURBO ROTOR TO MAKE TAPPING NOISE GET A STETHESCOPE LISTEN AROUND THEN ENGINE BECAREFUL WATCH DRIVE BELT DONT GET HANDS, CLOTHES HAIR JEWRELY CAUGHT IN MOVING DRIVE.LISTEN AROUND ENGINE.THE STETHESCOPE CAN HELP YOU PIN POINT THE NOISE.YOU CAN BUY STETHESCOPE AT SEARS OR ANY AUTO PARTS STORES.

Jan 18, 2011 | 1999 Saab 9-5

1 Answer

On my 1994 L200 3000 mitsubishi there is a tappet which has stuck and is rattling,can you help.


Mits are well know for top end noisedue to hydrolic tappets. Note we are talking about a tapping or clicking sound here not a knock. You can try using an engine flush product if the noise is bad and then changing your oil. Follow manufactures instructions on the engine flush product. I have also used Marvel Mystery Oil (available at Walmart and most auto parts houses) with some success on this. Generally if the oil is not changed regularily eventually the tapping noise starts happening. FYI: hydrolic tappet can and do fail but generally the noise is associated with not maintaing oil changes

Mar 10, 2010 | Mitsubishi Pickup Cars & Trucks

1 Answer

How to replace front bearings on a 94 3000 Gt


If you are mechanically inclined, you can remove the tires, brake caliper, pads, assembly, disc. Remove, drive shaft nut. Disconnect tie rod end, strut, push out of place the drive shaft. Then you have to remove the ball joint nut that holds the knuckle in place and lastly you will have to send the knuckle to a machine shop to have the bearing pressed out or if you have a press, you are gold...
As you can see, it is quite some work, but it can be done under 2 hours each side.
The good news is that once you have them swaped and everything put back together. The car will feel a million times newer ;) (the "like on rails" feel)

Mar 07, 2010 | 1994 Mitsubishi 3000GT

1 Answer

I have a 2003 Subaru Forester (123,000Km) and


If it is a piston or other bad noise it will not go away. If this is what is happening then a good auto mechanic will have to listen to and isolate the noise before they can tell how much it will cost to fix it. Its usually not the piston.If after the car runs for a little while the noise gos away its usually dirt in the engine.Before you think about a very expensive repair try this.Change the oil and filter. Use only good quality oil and a Fram TG or a Purolator Pure One oil filter.My car likes the Castrol Sin Tec Synthetic oil. Yes synthetic cost more but it is better oil.
Let the car warm a little before you drive it every time you start it cold.
Dont let someone drive your car when you are not in the car. I know someone who has a son that was raceing his car when his son told him he was going to the library.
Do your next oil and filter change only after 2000-3000 miles.Then after that no more than 4000 miles between changes.Be nice to your car.
All this I am telling you is only if your noise gos away after tap tap as you said right after you start your car.
I hope this info helps you.

Sep 26, 2009 | 2003 Subaru Forester

2 Answers

Radio Code for 1995 Mitsubishi 3000 GT


you have to go to a mitsubishi dealer and have them look this information up for you. for security you should have a card that came with the card that has the code on it. check your manual and glovebox to be sure but otherwise a dealers the only solution and they need to see you and the car in person.

Oct 27, 2008 | 1995 Mitsubishi 3000GT

1 Answer

Tapping noise


A tapping sound could be lifter tick, or rod knock... if it goes away, what you have is lifter tick, check your oil, low oil makes it worse.

Oil pumps up the hydraulic lash adjusters in your valve covers, at lower RPMs, the oil pressure is lower and will not fully pressurize them. Try holding your rpm at about 3500 or so with the car in neutral (parked) and see if it goes away, it should.

In later years (I think starting in 97 or so) mitsu started using a larger bore so called "third gen" lash adjuster. They don't tick as much, but they still do at times.

The good news, lash adjusters are not THAT hard to replace, figure a set of 24 will run you less than 150 in parts.

The better news, it doesn't hurt anything, as long as you can live with the sound, there isn't any reason to change them.

Good luck,
Scott
Iceman_ii on 3si.org

Sep 23, 2008 | 1994 Mitsubishi 3000GT

Not finding what you are looking for?
1994 Mitsubishi 3000GT Logo

Related Topics:

299 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...