Question about 1995 Mitsubishi Diamante

1 Answer

1995 mitsubishi diamate transmission

When i put the car in drive or reverse it won't move. it'll move a little but it jerks and makes this funny noise. what should i do

Posted by on

  • ash seder May 11, 2010

    what happens if you put the car into first?

    im not being smart this is a legit question


×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check out the timming belt

Posted on Dec 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Transmission make loud sound when put it in revers


PLEASE HELP! SOS! car starts but doesnt move! - Club3G Forum ...

www.club3g.com > ... > Performance & Tech Forums > Problem Reports

Nov 16, 2010 - 61 posts - ‎14 authors
now yes, i will take the transmission is fubar into consideration but theres an .....however... idk about my cv joint, my car ONLY would make a loud ping noise when i move from a stop or brake ..... almost always when i put it into reverse. such as an engine mount sound, ... Vehicle: 2004 Eclipse Spyder GT. Loud knocking sound after oil change..
14 posts
Sep 20, 2010
Horrible noise upon start when cold
21 posts
Dec 24, 2009
Sporty knocking.. Oh noez!!one!!1!
16 posts
Mar 22, 2006
More results from www.club3g.com

Loud thump when I shift into drive or reverse - CarGurus

www.cargurus.com > Questions > Chevrolet > Cavalier

CarGurusDec 19, 2012 - And while driving loud thump when car motor shifts th... ... Bad throttle position sensor can trip both lights and make the transmission shift at high rpms and shift hard even under light acceleration. .... the transmission will shift hard when firstput into reverse or drive ... 2004 Chevrolet Cavalier LS For Sale.Missing: mitsubishi ‎eclipse

Mitsubishi Transmissions & Drivetrains Repair Questions ...


Dec 06, 2015 | 2004 Mitsubishi Eclipse

1 Answer

My 2001 eclipse automatic would not move in reverse,drive and all other gears just for a momment but now works but has no power from the stop position and takes forever to get up to speed


The slip disks in your automatic transmission and some synchronizers are worn out. Your transmission needs to be overhauled and repaired.

Mar 12, 2014 | 2001 Mitsubishi Eclipse

1 Answer

2002 Mitsubishi Eclipse, I came to a stop and my car would just rev when I pressed the gas. Noticed my neutral light blink, Car won't move in drive or reverse just rev. help please!


This just happened to my 02 eclipse gt automatic on Thanksgiving 2012 . Its ur torque converter , the torque converter engages forward and reverse drive... Sorry to say but u need a transmission rebuild.... I just swapped mine to a 5 speed for around $2000

Jan 10, 2013 | 2001 Mitsubishi Eclipse

1 Answer

2004 Lincoln aviator goes into gear but won't move


bad transmission maybe. Try going into a lower gear (2 or 1) and giving it a little gas and holding it there. (about 2500 rpm) Hold it there for about 30 seconds.
If it still doesnt move, look under at the side of the transmission where the shifter cable connects and make sure it is moving.
Make sure the brake is on and the wheels are blocked and have a friend shift it back and forth while you look.
Sometimes, the connection pin comes out and you wont shift. .
If it does move right away, head to the transmission shop.

Dec 30, 2012 | 2004 Lincoln Aviator

1 Answer

Car jerks when you shift gears


If that oil is transmission fluid, you may be low on fluid. That would cause harsh shifts. Make sure your transmission is full.
Is it just reverse and drive that ****? Do second and third shift smooth? If so, you may have a too-high idle.
If idle is good, and your transmission didn't get low on fluid, then I would suggest you drain and refill the transmission, and install a new transmission filter while you have the bottom pan off. Usually, you can buy a filter and pan gasket as a kit.

Nov 17, 2011 | Mitsubishi Cars & Trucks

1 Answer

I have a 1996 Mitsubishi Galant S with a manual transmission and when i step on the gas pedal in first gear the car doesnt move. When I put the car in reverse, it doesnt move. Prior to this happening my...


For a manual transmission, this means your clutch has completely failed. The loud noise was likely not a belt, but the cluch release bearing. I'll bet this was a screeching noise that reduced or stopped when the clutch pedal was depressed.

You'll need a new replacement pressure plate, driven plate, release bearing and anything else that is found to be worn out when the the transmission is removed to do the job. A garage would need 4-6 hours labour to do this.

SD

Jun 25, 2011 | 1996 Mitsubishi Galant

1 Answer

While driving my Mitsubishi Diamante 2002 I just felt the car don't respond to the shift changes and lost power. Now the car can't respond to drive, reverse, etc...


my 02 mitsubishi diamate transmission is in a fail/safe mode how do i get it out of that mode?transmission only works n 2nd,3rd ,park,nuetral,&reverse

Dec 21, 2010 | 2002 Mitsubishi Diamante

Not finding what you are looking for?
1995 Mitsubishi Diamante Logo

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...