Question about 1992 Lexus Ls 400

1 Answer

Timing belt how to set marks

Posted by on

  • yadayada
    yadayada May 11, 2010

    buddy, your best bet is to go to a lexus dealer and buy the genuine shop manuals for your LS, those manuals are very detailed and shoud provide a list of special tools needed for the job u are planning, I must warn u though, shop around if you can cause those manuals can be pricey, but they are worth it..
    good luck

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lexus Master
  • 1,757 Answers

My sincere apologies for the severly delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, however I am answering it in case you still do.

Click on the following direct Link. It has several Diagrams for your 1992 Lexus LS400 Timing Belt.

Again my apologies...
Let me know if this helped or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1992/make/lexus/model/ls_400/1992_lexus_ls_400_timing_belt_diagram_marks.htm

Posted on Mar 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 ford ranger 2.3 timing belt pully diagram


Set the crank to TDC using the timing marks, Then look for an arrow or a mark on the cam shaft pully and another mark on the block. Line those up. Put the belt on, make sure the marks did not move.

Feb 12, 2013 | Cars & Trucks

1 Answer

1990 ford ranger 2.3 timing belt pully diagram


Set the crank to TDC using the timing marks, look for a mark on the cam pulley and a mark on the head, line those marks up and put on the belt

Feb 12, 2013 | Cars & Trucks

1 Answer

I REPLACED TIMING BELT .AND I WANT TO KNOW HOW TO RESET THE TIMING ,SO AS NOT TO DAMAGE TO MOTOR. WHEN I GO TO START IT UP .


If you did not set the gears(pulleys) in the same place or set the marks in the timing belt to the marks in the gears the car wont start. when you do the the job is when you set the timing, not after you done. If you use a cheap timing belt those belts do not have marks, I recommend to get a belt from toyota that has a mark for each cam pulley and another mark for the crank pulley. Toyota doesn't have interference engines, so no matter how bad is your timing the car wont start just spin.

Dec 25, 2010 | 1994 Toyota 4Runner

1 Answer

How do set the timing on hyundai excel 1998


Hi,


It seems you are encountering problems trying to set the timing marks in your elantra,not to worry,simply follow the stepwise solution below;
Ensure timing marks aligned [6] & [7] .

STEP 1. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets.

STEP 2. Slacken tensioner pulley bolt [8].Push tensioner pulley firmly against timing belt to tension belt.



STEP 3. Tighten tensioner pulley bolt [8] . Tightening torque: 43-55 Nm.


STEP 4. Except Matrix: Turn crankshaft one turn clockwise.



STEP 5. Matrix: Turn crankshaft two turns clockwise.


STEP 6. Ensure timing marks aligned [6] .


STEP 7. Apply a load of 2 kg to belt at .Belt should deflect 4-6 mm. If not Adjust position of tensioner pulley.



STEP 8. Install components in reverse order of removal.


STEP 9. Tighten crankshaft pulley bolt [2] . Tightening torque: 170-180 Nm
(7) is timing mark on cam,pin mark to top,hole in spoke below pin mark lines up with mark on head (6) is crank timing mark,pin mark on crank lines up with markS on block.





Good luck.

Aug 20, 2010 | Hyundai Excel Cars & Trucks

1 Answer

I have a 2000 dodge caravan trying to time it dont know how has a 3.0 motor


set the timing mark on the crankshaft to the mark on the oil pump, then set the timing mark on the camshaft to the mark on the alternator bracket/set second camshaft mark to mark on the inner timing belt cover. line up all mark as decribed. be sure before u set anything to bring #1 piston all the way up to top. with belt on turn crankshaft 2 full turns to bring #1 piston back to top if the cams are not lined up correctly loosen belt and start over again until everything lines up correctly. you may have to do this a few times but it will work.

Mar 31, 2010 | 2002 Dodge Caravan

1 Answer

Timing marks setting Hyundai Lantra


Installation
Ensure timing marks aligned [6] & [7] . 1. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets. 2. Slacken tensioner pulley bolt [8] . Push tensioner pulley firmly against timing belt to tension belt. 3. Tighten tensioner pulley bolt [8] . Tightening torque: 43-55 Nm. 4. Except Matrix: Turn crankshaft one turn clockwise. 5. Matrix: Turn crankshaft two turns clockwise. 6. Ensure timing marks aligned [6] . 7. Apply a load of 2 kg to belt at . Belt should deflect 4-6 mm. If not: Adjust position of tensioner pulley. 8. Install components in reverse order of removal. 9. Tighten crankshaft pulley bolt [2] . Tightening torque: 170-180 Nm

7 is timing mark on cam,pin mark to top,hole in spoke below pin mark lines up with mark on head
6 is crank timing mark,pin mark on crank lines up with mark on block
NOTE this mark is just before top


Mar 21, 2010 | Hyundai Motor 1996 Elantra

1 Answer

Timing belt broke on a 95 ford ranger.new belt


you have to line up the two marks on the gears and set the tension to the correct setting. then check the marks again. trial and error. i just did my timing belt on my ranger haha

Feb 18, 2010 | 1995 Ford Ranger Supercab

1 Answer

How to set timming belt,cant find mark for crankshaft 3.0L


Timing belt removed, static timing was not set before removing timing belt.

[Set Static Timing:
No.1 piston is brought up to TDC before removing timing belt.

Cam gear has a punchmark on face of gear, and this mark aligns with one single tooth. There is a matching punchmark on the Timing Belt Rear Upper Cover.

Facing the cam gear, the mark is to the upper right. There is an 'egg shape' of the timing belt upper rear cover, in this spot. This punchmark is in that 'egg shape', and is close to a bolt hole. The cam gear mark lines up with the Timing Belt Rear Upper Cover, mark.

The crankshaft gear has a punchmark on the face. It lines up with one single tooth. There is a corresponding punchmark on the lower right side. An alignment mark)

Should be a round punchmark on the face of the crankshaft gear. It lines up with a single tooth. Wipe the gear clean, use a little carb cleaner. (NO flames, or sparks nearby, well ventilated area)

Barring you cannot find the crankshaft mark, find the camshaft alignment marks, make sure they are aligned with the alignment, (Punchmark), on the Timing Upper Rear Cover.

Count the teeth in the timing belt. There should be 133 teeth on the belt.

There is 43 teeth in-between the timing mark of the camshaft, and the timing mark on the crankshaft.

(43 teeth in-between the Right Side Camshaft mark to crankshaft mark, 43 teeth in-between the Left Side Camshaft mark to crankshaft mark)

There should be 40 teeth in-between the two cam gears.




Oct 24, 2009 | 1989 Nissan Pathfinder

1 Answer

Timing belt settings


the tension setting for the belt?

or the timing marks? the timing marks differ. best set cyl. no 1 to tdc.. take out no. 1 spark plug and put sumthin long and thin down the hole.. like a long quarter drive extension.. and check to see that cyl 1 is at tdc.. then set your cam to the OT marks marked on the cam pulley and rocker cover... then you have to set the distributor also.. slacken the 13mm bolt for the dizzy clamp... you will find a line on the lip of the dizzy body.. this needs to align with the middle of rotor arm tip... (sumtimes a mark on the roror arm tip)... tension belt and your timing is set.. set your timing incorrectly and the car will run rough and not rev past 5k...

Sep 26, 2008 | 1993 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

289 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...