Question about 1988 Ford F 250

1 Answer

Compresshion specs What is the the compresshion in foot lbs. suppose to be? I need to do a compersshion check.

Posted by on

  • Roberta Smith
    Roberta Smith May 11, 2010

    what motor is in it ?





    Robert

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,586 Answers

Compression tests are almost always done in psi, not ft-lbs - if you get the gauge from a parts store, it's likely in psi.

Posted on Sep 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Caliper bolts get loose


the main mounting bolts? not guides?
caliper mount to knuckle bolts?
what torque did you use? in foot/lbs.

  1. id bet they are not factory spec bolts
  2. or you used the wrong torque page.
  3. or your tool is no good. (harbor fright tools?)
use a beam torque tool, it will never fib to you, like cheap clickers do.
I promise.
specs
tighten the caliper pin bolts to 26 ft. lbs. (36 Nm). Bottom bolt
there are 4 bolts specs here.
above pin
banjo 17ft/lbs
top B bolts is 61.5 foot lbs. (this came loose at 61 ?)
C spec is 5ft/lbs on bleeder nipples.

now alternator tack.
the rotor is warped so bad it bead the calipers to death.
the wheel bearing, is so bad , same.

ever check those for run out, and end play?
bingo if true.
damage and collateral damage are limitless.
and rust too. (entropy of all kinds)

Apr 16, 2014 | 2010 Suzuki Grand Vitara

1 Answer

Just need the torque specs for 2002 kia sportage flywheel pressure plate and exhaust manifold to cylinder head...please


flywheel'flexplate 73 ft lbs Exhaust nuts 31 foot lbs Exhaust bolts 18 ft lbs
You say pressure plate, is this manual transmission?

Mar 28, 2011 | 2002 Kia Sportage

2 Answers

Need torque specs for 2000 chevy malibu 3.1 cyl heads & intake


(step 1 ) the torque specs for the heads are---1998 through 2001 are 37 foot lbs. ( step 2) rotate an additional 90-degrees (1/4 turn). intake manifold bolts ( lower ) step 1-- 62 in-lbs, step 2--115 in-lbs. intake manifold bolts/studs ( upper ) 18 ft-lbs. this is for the 3.1 v-6, have a good day!

Aug 14, 2010 | 2000 Chevrolet Malibu

1 Answer

Proper torque for bolts on front wheel


The axle nut spec is 177 foot lbs. and the bearing to knuckle bolts spec is 133 foot lbs.

Dec 23, 2009 | 2004 GMC Yukon

2 Answers

What is the torque setting for lug nuts on a small pickup


if these wheels are steel the torque spec should be 87 foot lbs...aluminum take them up to 90 foot lbs

Nov 14, 2009 | 1992 Toyota Pickup

2 Answers

Head gasket torque specs


Here you go, I hope this is what you were looking for:

For 1987-94 models, the cylinder head bolts are tightened in 3 progressive steps. Tighten them in the proper sequence as follows:
Step 1: 50-55 ft. lbs. (68-75 Nm) Step 2: 60-65 ft. lbs. (81-88 Nm) Step 3: 70-85 ft. lbs. (95-115 Nm) Let me know if I can assist you with anything else.

Apr 30, 2009 | Ford F-150 Cars & Trucks

1 Answer

I need torque specs for 94 rodeo


flywheel 80-90 foot lbs (new bolts 90), press plate 45 foot lbs

Feb 14, 2009 | 1995 Isuzu Rodeo

1 Answer

Looking for the torque specs for 1998 chevy astro van?


1998 chevy astro 4.3 v6 torque specs include :
* foot pounds *
balance shaft (if equiped) gear bolt = step 1 = 15 ft.lbs. step2 = additional 35 degrees.
camshaft sprocket bolt = 18 ft. lbs.
connecting rod cap = step 1 = 20 ft. lbs. step 2 = additional 70 degrees.
crankshaft damper bolt = 74 ft. lbs.
crankshaft oil deflectorbolt/nut = 27 ft.lbs.
cylinder head bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees. (tighten in sequence)
2811243.jpg


exhaust manifold bolts = step 1 = 11 ft. lbs. step 2 = 22 ft. lbs.
flywheel bolt = 74 ft. lbs.
main bearing cap bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees.
oil filter adapter bolt = 15 ft. lbs.
oil pan bolt/nut = 18 ft. lbs.
oil pump bolt = 66 ft. lbs.
rocker arm with press in studs = 18 ft. lbs.
rocker arm with screw in studs = 19 ft. lbs.
valve lifter retainer bolt = 12 ft. lbs.
water pump bolt = 33 ft. lbs.
* inch pounds *
balance shaft retaining plate bolt = 106 in. lbs.
camshaft retainer plate bolt = 106 in. lbs.
front cover bolt = 106 in. lbs.
intake manifold upper = step 1 = 44 in. lbs. step 2 = 88 in. lbs.
intake manifold lower = step 1 = 27 in. lbs. step 2 = 106 in. lbs. step 3 = 133 in. lbs. ** (tighten bolts in sequence)

cbb8861.jpg

thanks for your vote !

Dec 28, 2008 | 1998 Chevrolet Astro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...