Question about 1999 Toyota Corolla

1 Answer

1999 Toyota Corolla security system

Yes, the LED is solid red. I observed today that it lights when engine is off. But I don't know what brand of alarm do I have. I just bought it with used car few weeks ago. But I read DEI on the viper. Does that make sense?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

Yes it does, there should be a black small button under the drivers dash .could be hidden so look with a light, once you find it you need to turn your ignition on then turn it off and press the button within 10 seconds the LED should turn off and the alarm should be working normally

Posted on Sep 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Two of my smoke alarms went off (no fire/smoke in or near house), one has a green light blinking and one has a solid green light, which need a new battery/reset?


The constant green LED means the alarm has AC power.
A flashing green light every 2 seconds without an audible alert means the unit recently sounded ( was the one activated ) and is now in latching mode to let you know that it was the unit that detected the problem. To clear the latching mode hold down the test button for 5 seconds.
Red LED flashing once per minute means that the back-up battery is connected and functioning.
Red light flashing constantly during alarm means that it is the unit that initiated the alarm siren.

Sep 04, 2014 | Cars & Trucks

1 Answer

How do I reset alarm on Toyota corola 2002


You'll need to set off the alarm for a few seconds.
then, look under the dash area for a button or, a toggle
switch. When you locate it, turn on the ignition
key, press and hold in the button (little
spring loaded micro button, red or black possibly)
until the alarm chirps 1 time. This should over ride
the system, and only the keyless entry part,
if installed, would still be operating.
The LED (light emiting diode) light in the dash
should also go on solid.

At this point. the alarm would have reset.
If this had a starter kill relay installed,
it would now be opened, and the engine would
turn over when tried. This is override/reset.

Oct 30, 2012 | 2004 Toyota Corolla

1 Answer

Hello I have a 1994 maxima manual transmision,it have a check engine light on,when I start the car and beguin to drive it,runs perfect the a few minutes later the car gets very lazy almost want to turn...


Hello! I'll need the trouble code to fix your vehicle...Below is procedure with a code list...Guru...saailer

Remove the trim panels in front of the center console. Locate the engine computer attached to a floor-mounted bracket on the transmission tunnel between the console and the firewall.

  • Turn the diagnostic mode selector, located in a round opening on the side of the engine computer, until it stops. Observe the small red and green LED lights on the side of the computer next to the mode selector. They will flash to indicate the modes, with a pause between each mode. One quick flash is mode one, two quick flashes is mode two and so on. When the light flashes indicate mode three, quickly turn the mode selector counterclockwise until it stops. You have entered mode three diagnostics.

  • Remove the trim panels in front of the center console. Locate the engine computer attached to a floor-mounted bracket on the transmission tunnel between the console and the firewall.

  • Turn the diagnostic mode selector, located in a round opening on the side of the engine computer, until it stops. Observe the small red and green LED lights on the side of the computer next to the mode selector. They will flash to indicate the modes, with a pause between each mode. One quick flash is mode one, two quick flashes is mode two and so on. When the light flashes indicate mode three, quickly turn the mode selector counterclockwise until it stops. You have entered mode three diagnostics.
  • Turn the diagnostic mode selector, located in a round opening on the side of the engine computer, until it stops. Observe the small red and green LED lights on the side of the computer next to the mode selector. They will flash to indicate the modes, with a pause between each mode. One quick flash is mode one, two quick flashes is mode two and so on. When the light flashes indicate mode three, quickly turn the mode selector counterclockwise until it stops. You have entered mode three diagnostics.Observe the red and green LED lights on the side of the computer. The red light flashes to indicate the "Tens" digit of the code and the green light flashes to indicate the "Ones" digit of the code. For example, if the red light flashes two times and the green light flashes seven times, this would indicate code 27.


    Turn the ignition key off for two minutes to exit diagnostics. The computer will automatically return to mode one for normal operation...

    Code 11 Crank sensor angle

    Code 12 Mass airflow sensor

    Code 13 Engine coolant temperature sensor

    Code 14 Vehicle speed sensor

    Code 21 No ignition reference

    Code 22 Fuel pump

    Code 31 Engine control unit

    Code 32 EGR sensor

    Code 33 Oxygen sensor

    Code 34 Knock sensor

    Code 35 EGR temperature sensor

    Code 43 Throttle position sensor

    Code 45 Injector leak

    Code 51 Injector circuit

    Code 54 Automatic transmission signal

    Code 55 No malfunction recorded

    May 04, 2012 | 1994 Nissan Maxima

    1 Answer

    The alarm (that I didn't know I had) on my 1997 Toyota Corolla went off when I tried to jump start it, and now I can't start my car at all. There is a brand new battery in there now, and the alarm keeps...


    Put the key in the ignition, and turn forward
    all the way just before cranking. Then within
    5 seconds, locate, press and hold in the
    valet/overide button, found under the
    dash area, (push button, spring loaded)
    until the installed LED (the blinking light)
    in your dash area goes on solid,
    and the siren chirps once.

    This should reset the alarm, and reset
    the grounded relay on the starter wire,
    allowing you to start the engine.

    Jan 06, 2011 | Toyota Corolla Cars & Trucks

    1 Answer

    Alarm will not go off


    Answer
    Gotcha, let's put it into valet/service mode,
    and try to reset the alarm to default mode.

    Look under the dash area for a button or, a toggle
    switch. When you locate it, turn on the ignition
    key, press and hold in the button (little
    spring loaded micro button, red or black possibly)
    until the alarm chirps 1 time. This should over ride
    the system, and only the keyless entry part,
    if installed, would still be operating.
    The LED (light emiting diode) light in the dash
    should also go on solid.

    At this point. the alarm would have reset.
    If this had a starter kill relay installed,
    it would now be opened, and the engine would
    turn over when tried.

    You would repeat these steps to go back to
    user mode to see if this was corrected.

    Let me know if it works for yours.

    ALARMTEK
    INSTALLSUPPORT.COM

    Nov 07, 2009 | 1995 Chevrolet Lumina

    2 Answers

    2000 Toyota Corolla wont start Changed 02 sensor disconnected bat


    that red LED is the Alarm, if its solid red, its fine; blinking is about to trigger I think and off means the Alarm is active and opening a door will set it off.

    as to why it wont start...not a clue,
    check gas, make sure its in park,
    you said its turning over but not firing, perhaps its a bad sparkplug or just flooded...

    Apr 17, 2009 | 2000 BMW 3 Series

    1 Answer

    Toyota Corolla VE 1999


    Ok, If the LED is Solid on red that mean the alarm is in the valet mode .do you know want brand alarm you have?

    Sep 22, 2008 | 1999 Toyota Corolla

    2 Answers

    When you try to start car the alarm goes off and car wont start and horn goes on and off the locks click back and forth


    '99 camry: with alarm sounding. turn key to "ON" position and press in and hold alarm button (red two position (in /out) on dash board. Button should go from flashing red to solid red. Release button when it stays lit (solid bright red) . Alarm is now in disabled mode and engine should crank when key is turned to "start" position. "Thank you" for over the phone tech support at Richardson Toyota in Texas.

    Aug 03, 2008 | 1999 Toyota Camry

    Not finding what you are looking for?
    1999 Toyota Corolla Logo

    633 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    60667 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21936 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6811 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...