Question about 1997 Chrysler Town & Country

1 Answer

Fuel pump how do i take off the two hoses off the fuel pump and the wire's that are also connected to the fuel pump???

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,263 Answers

There are plastic clips that hold the lines on. i usually just breakthese because you can find replacement cliups at napa for a few bucks. the wires should have a plug from a harness that runs along the frame disconnect it then drop the tank and remove hold down ring for the pump this will allow you to remove the pump with the float. please rate this.

Posted on Sep 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Installing rebuilt pump don't know were to start never worked diesel before know anything about injector pumps.


When installing a new fuel pump on a ud truck 1400 1994 desiel.......

Resolved Question:

When installing a new fuel pump on a ud truck 1400 1994 desiel....... how do you set the timing, i can't find a mark on the pump. Submitted: 3 years ago. Category: Medium and Heavy Trucks Share this conversation Mechanic's answer sascityks.64x64.jpg"> Tkman55 , Mechanic 125 Satisfied Customers Expert: tkman55 replied 3 years ago. Let me see if I can help you with your problem. Please don't rate me until all your questions are answered, that way you will not have to pay twice. Always use "Reply To Expert" link. Thanks.
If you are new to the site this is how it works:
1. We will go back and forth as needed until you get the help you need, there will be no extra cost for replying.
2. I will give you the best possible information without actually being physically present with you.
3. Remember to leave a positive rating after we are finished.
INJECTION PUMP

Removal
  • 1. Disconnect negative battery cable. Remove injection tubes from nozzles and plug nozzles. Remove fuel cut solenoid wire and accelerator wire. Disconnect fuel inlet hose, overflow hose and fuel return hose. Remove injection pump drive gear cover. Mark injection pump shaft and gear for proper alignment during reassembly.
  • 2. Loosen injection pump drive gear nut and remove gear. Remove injection pump bolts and nuts. Remove injection pump with injection tubes attached.

Disassembly & Inspection
For disassembly, inspection and reassembly procedures for injection pump or injectors, see DISASSEMBLY & REASSEMBLY in Fuel System article.

Installation
  • 1. Turn engine until No. 1 piston is at TDC on compression stroke. Install injection pump assembly. Install injection pump gear so that flange is aligned with mark on front cover. See Error! Hyperlink reference not valid. . Install gear nut and tighten to 43-51 Ft. Lbs. (59-69 N.m). Tighten injection pump fixing bolts. See INJECTION PUMP MOUNTING TORQUE table. Tighten injection pump to mounting bracket bolts.
  • 2. Install injection pump gear cover with new gasket. Connect fuel inlet hose, overflow hose and fuel return hose. Connect fuel cut solenoid wire and accelerator wire. Connect injection tubes to nozzles. Tighten tube flare nuts to 14-18 Ft. Lbs. (20-25 N.m).
  • 3. Connect negative battery terminal.


Read more: http://www.justanswer.com/medium-and-heavy-truck/746q8-when-installing-new-fuel-pump-ud-truck-1400-1994-desiel.html#ixzz3nAToQQfC

Sep 29, 2015 | Cars & Trucks

1 Answer

Where is the fuel pump located in a 1985 fiero


from autozone.com:

The Fiero is equipped with a electric fuel pump and gauge sending unit mounted in the fuel tank. The pump is serviced and a complete unit by removing the fuel tank.
REMOVAL & INSTALLATION

CAUTION To reduce the risk of fire and personal injury, it is necessary to relieve the fuel system pressure before servicing any fuel system component. If this procedure is not performed, fuel may be sprayed out of the connection under pressure. Always keep a dry chemical (Class B) fire extinguisher near the work area.

  1. Disconnect the negative (-) battery cable.
  2. Relieve the fuel system pressure.

Remove the fuel pump fuse from the fuse block located in the passenger compartment. Start the engine and run until the engine stops due to the lack of fuel. Crank the engine for 3 seconds to ensure all pressure is relieved.
  1. Drain all the fuel from the tank using a suction pump.
  2. Raise the vehicle and support with jackstands.
  3. Disconnect the wiring from the tank.
  4. Remove the ground wire retaining screw from under the body.
  5. Disconnect all hoses and filler neck from the tank.
  6. Support the tank on a jack and remove the retaining strap nuts.
  7. Lower the tank enough to disconnect the fuel sending unit wires.
  8. Disconnect the fuel line, vapor line and return line.
  9. Remove the tank from the vehicle.
  10. Remove the fuel gauge/pump retaining ring by turning the cam lock ring counterclockwise using a spanner wrench such as tool J-24187.
  11. Remove the gauge unit and the pump.

To install:
  1. Inspect the fuel pump attaching hose for any signs of deterioration and replace if necessary. Also, check the rubber sound insulator at the bottom of the pump.
  2. Push the fuel pump assembly into the attaching hose.
  3. Using a new O-ring seal, install the pump assembly into the tank.
  4. Install the cam lock ring over the pump and lock by turning clockwise with a spanner wrench J-24187 or equivalent.
  5. Support the tank on a suitable jack.
  6. Raise the tank enough to connect all fuel and filler hoses.
  7. Connect all electrical wires to the pump and tank.
  8. Raise the tank and install the retaining strap nuts. Use new sound reducing pad if they are damaged. Check all connections and wire to ensure proper installation before refilling the tank.
  9. Refill the tank with unleaded fuel. Reconnect the negative (-) battery cable.
  10. Start the engine and check for fuel leaks and gauge operation.

Nov 07, 2010 | 1985 Pontiac Fiero

3 Answers

Do I have to drop the fuel tank to replace the fuel pump on a 94 Buick le saber


Yes ,,instructions are below, Use eye protection for this procedure
Remove or Disconnect:

  1. Relieve Fuel Pressure
  2. Disconnect negative battery cable
  3. Raise vehicle on hoist
  4. Remove Fuel Tank
  5. Remove Fuel Gage sending and pump assembly by turning cam lock ring counterclockwise. Lift assembly from fuel tank and remove fuel pump from fuel gage sender unit.
  6. Disconnect pump wires, hose clamps, and clamp around pump body
  7. Pull pump assembly out of rubber connectors
  8. Inspect fuel pump attaching hose for any signs of deterioration. Replace as necessary.
Install or Connect:

  1. Push fuel pump assembly into attaching hose
  2. Connect pump wires, hose clamps at attaching hose and around pump body
  3. Place Fuel tank sending unit and pump assembly into tank using new O-ring
  4. Place cam lock over assembly and lock by turning clockwise
  5. Install Fuel Tank
  6. Start engine and check fuel pipe connector for visual leaks

Oct 20, 2010 | 1994 Buick LeSabre

1 Answer

Where is the fuel pump located on a 92 Lexus SC300?


Fuel Pump REMOVAL AND INSTALLATION ES300 CAUTION
Fuel injection systems remain under pressure even after the engine has been turned OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.
  1. Relieve the fuel system pressure.
  2. With the ignition switch in the LOCK position, disconnect the negative battery terminal. If equipped with an air bag system, wait at least 90 seconds or longer before performing any other work.
  3. Remove the rear seat cushion.
  4. Disconnect the fuel pump connector. CAUTION
    The Supplemental Inflatable Restraint (SIR) system must be disarmed before removing the fuel pump. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.
  5. Remove the floor service hole cover. NOTE: Do not lift the fuel pump assembly up using the wire harness.
  6. Remove the fuel filler cap. Disconnect the fuel outlet pipe and the return hose from the pump bracket.
  7. Remove the 8 screws and lift out the pump/bracket assembly with gasket.
  8. Remove the fuel pump lead wire.
  9. Pull the lower end of the pump off of the bracket.
  10. Disconnect the fuel hose from the pump and remove the pump.
  11. Remove the rubber cushion from the pump. To install:
  12. Install the filter and rubber cushion on the new pump and install the pump on the bracket.
  13. Connect the fuel hose and the wire connector on the pump.
  14. Using a new gasket, install the pump and tighten the eight screws to 35 inch lbs. (4 Nm).
  15. Connect the fuel pipe and return hose to the pump and tighten the bolts to 22 ft. lbs. (29 Nm).
  16. Connect the wire, install the service cover and replace the rear seat.
  17. Connect the negative battery cable.
  18. Start the engine and check for leaks. Fig. 1: Fuel pump assembly - ES300 294126.gif
GS300, LS400, SC300 and SC400
  1. Disconnect the negative battery cable. Wait at least 90 seconds before performing any other work.
  2. Remove the trunk floor mat.
  3. Remove the trunk trim cover.
  4. Disconnect the fuel pump electrical connector.
  5. Remove the rear seat bottom and seat back.
  6. Remove the partition cover.
  7. Remove the mounting bolts and remove the fuel pump set plate.
  8. Remove the three nuts and disconnect the fuel pump bracket from the tank.
  9. Disconnect the fuel hose from the bracket. Remove the pump, bracket and set plate as an assembly. To install:
  10. Install a new gasket on the set plate. Connect the fuel hose to the pump and bracket,
  11. Install the pump and bracket assembly with the three nuts; tighten the nuts to 48 inch lbs. (5 Nm). Install the set plate and tighten the bolts to 26 inch lbs. (3 Nm).
  12. Install the panel partition
  13. Install the rear seat cushion and back.
  14. Connect the fuel pump electrical connector.
  15. Install the trim panel.
  16. Install the spare tire and the trunk floor mat.
  17. Connect the negative battery cable.
  18. Start the engine; check the fuel system for leaks
  19. Road test the vehicle for proper operation.

Oct 13, 2010 | 1992 Lexus Sc 300

1 Answer

I need a diagram to replace a fuel tank on a 1987 vw cabriolet


1987 Volkswagen Cabriolet 1.8L FI SOHC 4cyl

1985-89 Scirocco and Cabriolet
  1. Disconnect the negative battery cable and drain the fuel tank.
  2. Remove the rear right wheel housing cover.
  3. Disconnect the large breather hose from the filler neck.
  4. Pull the gravity valve down leaving the hoses connected.
  5. Unbolt the fuel pump bracket from the body and lower the pump.
  6. Remove the fuel tank screw.
  7. Disconnect the fuel pump hose and pull the blue hose from the return line.
  8. Disconnect the brake hoses from both sides of the rear axle and plug them.
  9. Disconnect the rear axle from both sides of the body and allow it to swing down and rest on the handbrake cable guides.
  10. Unhook the rear muffler support lugs.
  11. Disconnect the filler hose from the tank.
  12. Support the tank, remove the tank fasteners and lower the tank enough to disconnect the fuel gauge sending unit wires and breather hoses.
  13. Remove the fuel tank.

To install:
If installing a new or used tank, make note of where the old foam strips were installed, and install new foam strips on the replacement tank in the same locations.
  1. Raise and support tank. Connect the small breather hoses and fuel gauge sending unit wires. Install the tank fasteners.

When connecting the breather hoses, position the hose clips so that they do not make contact with the body.
  1. Connect the filler hose to the tank and connect the rear muffler support lugs.
  2. Raise the rear axle off the handbrake cable guides and install.
  3. Connect the brake hoses and bleed the brakes.
  4. Connect the return line and fuel pump hose.
  5. Install the fuel tank screw.
  6. Raise the fuel pump and attach the fuel pump bracket to the body.
  7. Put the gravity valve back into its original (raised) position.
  8. Connect the large breather hose to the filler neck.

When connecting the breather hose, position the hose clip so that it does not make contact with the body.
  1. Install the right rear wheel housing cover.
  2. Fill the tank and connect the negative battery cable.

40071b2.jpg

Fig. 1: Fuel tank assembly used on the Rabbit Pick-up. Other models are similar

Hope helps (remember to rate and comment this).

Sep 21, 2010 | Volkswagen Cabriolet Cars & Trucks

1 Answer

Where is the fuel pump located in a 1990 geo prizm? Is it in the fuel tank or on the fuel line?


Electric Fuel Pump REMOVAL & INSTALLATION The electric fuel pump used on fuel injected Nova and Prizm cars is contained within the fuel tank. On 1988–92 models it cannot be removed without removing the tank from the car. NOTE: Before removing fuel system parts, clean them with a spray-type engine cleaner. Follow the instructions on the cleaner. Do not soak fuel system parts in liquid cleaning solvent. CAUTION
The fuel injection system is under pressure. Refer to the procedure above and release pressure slowly and contain spillage. Observe no smoking/no open flame precautions. Have a Class B-C (dry powder) fire extinguisher within arm's reach at all times. 1988–92
  1. Release the fuel system pressure as outlined earlier.
  2. Using a siphon or pump, drain the fuel from the tank and store it in a proper metal container with a tight cap.
  3. Remove the rear seat cushion to gain access to the electrical wiring.
  4. Disconnect the fuel pump and sending unit wiring at the connector.
  5. Raise the vehicle and safely support it on jackstands.
  6. Loosen the clamp and remove the filler neck and overflow pipe from the tank.
  7. Remove the supply hose from the tank. Wrap a rag around the fitting to collect escaping fuel. Disconnect the breather hose from the tank, again using a rag to control spillage.
  8. Cover or plug the end of each disconnected line to keep dirt out and fuel in.
  9. Support the fuel tank with a floor jack or transmission jack. Use a broad piece of wood to distribute the load. Be careful not to deform the bottom of the tank.
  10. Remove the fuel tank support strap bolts.
  11. Swing the straps away from the tank and lower the jack. Balance the tank with your other hand or have a helper assist you. The tank is bulky and may have some fuel left in it. If its balance changes suddenly, the tank may fall.
  12. Remove the fuel filler pipe extension, the breather pipe assembly and the sending unit assembly. Keep these items in a clean, protected area away from the car.
  13. To remove the electric fuel pump:
    1. Disconnect the 2 pump-to-harness wires.
    2. Loosen the pump outlet hose clamp at the bracket pipe.
    3. Remove the pump from the bracket and the outlet hose from the bracket pipe.
    4. Separate the outlet hose and the filter from the pump.
  14. While the tank is out and disassembled, inspect it for any signs of rust, leakage or metal damage. If any problem is found, replace the tank. Clean the inside of the tank with water and a light detergent and rinse the tank thoroughly several times.
  15. Inspect all of the lines, hoses and fittings for any sign of corrosion, wear or damage to the surfaces. Check the pump outlet hose and the filter for restrictions. To install:
  16. When reassembling, ALWAYS replace the sealing gaskets with new ones. Also replace any rubber parts showing any sign of deterioration.
  17. Assemble the outlet hose and filter onto the pump; then attach the pump to the bracket.
  18. Connect the outlet hose clamp to the bracket pipe and connect the pump wiring to the harness wire.
  19. Install the fuel pump and bracket assembly onto the tank.
  20. Install the sending unit assembly.
  21. Connect the breather pipe assembly and the filler pipe extension. NOTE: Tighten the breather pipe screw to 17 inch lbs. and all other attaching screws to 30 inch lbs.
  22. Place the fuel tank on the jack and elevate it into place within the car. Attach the straps and install the strap bolts, tightening them to 29 ft. lbs.
  23. Connect the breather hose to the tank pipe, the return hose to the tank pipe and the supply hose to its tank pipe. tighten the supply hose fitting to 21 ft. lbs.
  24. Connect the filler neck and overflow pipe to the tank. Make sure the clamps are properly seated and secure.
  25. Lower the vehicle to the ground.
  26. Connect the pump and sending unit electrical connectors to the harness.
  27. Install the rear seat cushion.
  28. Using a funnel, pour the fuel that was drained from its container into the fuel filler.
  29. Install the fuel filler cap.
  30. Start the engine and check carefully for any sign of leakage around the tank and lines. Fig. 1: Fuel tank components — 1988 VIN Code 5 engine (Nova) 84225048.gif
    Fig. 2: Fuel tank components — 1989–92 84225049.gif

Aug 14, 2010 | 1990 Geo Prizm

1 Answer

How to remove fuel filter housing 97 ford f-350


FIRST YOU NEED A SUITABLE CONTAINER.PLACE UNDER FILTER DRAIN HOSE OPEN THE FILTER DRAIN.NOW YOU HAVE TO REMOVE THE TURBOCHARGER ASSEMBLY.REMOVE THE THE BAFFLE AND THE AIR INLET CROSSOVER MANIFOLD.REMOVE THE TWO CAPSCREWS SECURING THE FUEL FILTER BASE TO THE CRANLCASE.DISCONNECT THE WATER DRAIN HOSE FROM FILTER. DISCONNECT THE FUEL OUTLET HOSE LOCATED BETWEEN THE FUEL AND FILTER HOUSING.AND THE FUEL RETURN HOSE FROM THE FUEL PRESSURE REGULATOR VALVE.DISCONNECT THE TWO FUELSUPPLY HOSES THAT CONNECT THE REGULATOR BLOCK TO THE CYLINDER FUEL RAILS.LOOSEN THE CLAMP AT THE FUEL PUMP END OF THE HOSE WHICH CONNECTS THE FUEL FILTER TO THE INLET OF HIGH PRESSURE STAGE AT THE FUEL PUMP.DISENGAGE THE WIRING HARNESS FROM THE RIGHT SIDE OF THE FILTER HOUSING.DISENGAGE THE ELECTRICAL CONNECTIONS FROM THE WATER IN FUEL SENSOR AND THE FUEL HEATER.REMOVE THE FUEL FILTER.USE A PRYBAR TO REMOVE THE FUEL FILTER CAP AND THE FILTER ELEMENT WILL COME OUT WITH THE CAP.DEPRESS THE ELEMENT LOCKING TABS AND REMOVE THE ELEMENT FROM THE CAP.TO INSTALL CLEAN THE MATING SURFACES AND INSTALL THE FILTER ELEMENT ONTO THE CAP MAKING SURE THE TABS ENGAGE.INSTALL THE FILTER CAP AND PRESS DOWN FIRMLY BUT GENTLY TO ENGAGE IT.ENGAGE THE WIRING CONNECTIONS TO THE FUEL HEATER AND WIF SENSOR.ENGAGE THE WIRING HARNESS TO THE FILTER HOUSING.TIGHTEN THE CLAMP AT THE FUEL PUMP END OF HOSE WHICH CONNECTS THE FUEL FILTER TO THE INLET OF HIGH PRESSURE STAGE AT THE FUEL PUMP.ENGAGE THE TWO FUEL SUPPLY HOSES THAT CONNECT THE REGULATOR BLOCK TO THE CYLINDER HEAD FUEL RAILS.CONNECT THE FUEL OUTLET HOSE LOCATED BETWEEN THE FUEL AND FILTER HOUSING AND THE FUEL RETURN HOSE FROM THE FUEL PRESSURE REGULATOR VALVE.CONNECT THE WATER DRAIN HOSE TO THE FILTER.INSTALL THE 2 CAP SCREWS SECURING THE FUEL FILTER BASE TO THE CRANKCASE.INSTALL THE AIR INLET CROSSOVER MANIFOLD AND BAFFLE.INSTALL THE TURBOCHARGER ASSEMBLY.

Apr 03, 2010 | 1997 Ford F350 Crew Cab

1 Answer

Change fuel filter on 1994 celica


1994 Toyota Celica 1.8L EFI DOHC 4cyl
The Fuel Filter is located under hood, center, upper firewall, mounted in fuel line.

Common fuel line routing
8e18bc1.gif


View of the common electric fuel pump located under the rear seat
3a8ebd2.gif


Removal Fuel Pump

  1. Disconnect the negative battery cable.
  1. Remove the rear seat cushion.
  2. Unscrew the service hole cover.
  1. Disconnect the electrical fuel pump wiring at the pump assembly. Check for any fuel leakage while in there.
  1. Remove the gas cap, this will prevent any fuel gas spilling out of any high pressure lines.
  2. Using SST 09631-22020 or an equivalent line (flare nut) wrench, disconnect the outlet pipe from the pump bracket.
  1. Remove the pump bracket attaching screws.
  2. Disconnect the return hoses from the pump bracket, then pull out the pump/bracket assembly.
  1. Remove the nut and spring washer, then disconnect the wires from the pump bracket.
  1. Remove the sending unit attaching screws, then pull the unit from the bracket. To disassemble:
    1. Remove the lead wire.
    2. Pull the lower side of the fuel pump from the bracket.
    3. Remove the rubber cushion from the pump.
    4. Disconnect the hose from the pump and extract the pump.
    5. Separate the filter from the pump. Use a small screwdriver to remove the attaching clip.
    6. To remove the sender, disconnect the wiring from the bracket and unscrew the sender. Remove the screws, connector support, connector and gasket.
  2. Inspect all of the lines, hoses and fittings for any sign of corrosion, wear or damage to the surfaces. Check the pump outlet hose and the filter for restrictions.
  3. When reassembling, ALWAYS replace the sealing gaskets with new ones. Also replace any rubber parts showing any sign of deterioration.
To install:
  1. To assemble the pump:
    1. Secure and install a new gasket, connector and support with the screws.
    2. Attach the sensor and secure the screws, connect the wiring to the pump bracket.
    3. Install the pump filter using a new clip.
    4. Connect the outlet hose to the pump.
    5. Install the rubber cushion to the fuel pump. Push the lower side of the pump into place to secure on the bracket.
    6. Engage the connector to the fuel pump.

  2. Install the fuel sending unit to the pump bracket.
  3. Install the fuel pump and bracket assembly onto the tank. Use new gaskets. Tighten the pump bracket retaining screws to 31 inch lbs. (3 Nm).
  1. Connect the return hoses to the pump bracket.
  2. Install the service hole cover, then the engage the fuel pump and sending unit connector.
  3. Connect the negative battery cable
  4. Start the engine and check carefully for any sign of leakage around the tank and lines. Road test the vehicle for proper operation.
  5. Install the rear seat cushion.
I hope helps whit this (remember rated this help) Good luck.

Dec 17, 2009 | 1994 Toyota Celica

1 Answer

How to replace fuel pump 91 lesabre


Removal & Installation The fuel pump is located in the fuel tank. The fuel tank must be removed from the vehicle in order to access the pump.
  1. Properly relieve fuel system pressure.
  2. If not already done, disconnect the negative battery cable.
  3. Raise and safely support the vehicle.
  4. Safely drain and remove the fuel tank assembly, as outlined later in this section.
  5. If necessary, detach the quick-connect fittings from the fuel sender assembly and remove the fuel lines.
  6. Remove the fuel gauge sender and pump assembly by turning the cam locking ring counterclockwise. It may be necessary to use a spanner wrench, such as tool J-24187, to perform this.
  7. Carefully lift the assembly from the fuel tank, then remove the fuel pump from the fuel gauge sender unit.
  8. Remove the sender O-ring from the top of the sender and discard.
  9. Disconnect the pump wires, hose clamps and the clamp from around the pump body.
  10. Pull the pump assembly out of the rubber connectors.
  11. Inspect the fuel pump attaching hose for any signs of deterioration, and replace as necessary.
  12. To install:
    1. Push the fuel pump assembly into the attaching hose. Attach the pump electrical wires and fasten the hose clamps to the attaching hose and around the pump body.
    2. Place the fuel tank sender and pump assembly into the fuel tank. Use a new O-ring seal during assembly.
    3. Place the cam lock over the assembly, then lock by turning clockwise, using a suitable spanner wrench, if necessary.
    4. If removed, attach the fuel sender fuel line quick-connect fittings.
    When installing the fuel tank, make sure all rubber sound isolators or anti-squeak spacers are replaced in their original locations.
    1. Install the fuel tank, as outlined later in this section.
    2. Refill the fuel tank.
    3. Connect the negative battery cable.
    4. Turn the ignition switch to the ON position to pressurize the fuel system and check for leaks.

Oct 10, 2009 | 1991 Buick LeSabre

1 Answer

Fuel pump 1998 olds bravada


  1. Properly drain the fuel tank, then disconnect the negative battery cable.
  2. If not done already, raise and support the rear of the truck safely using jackstands.
  3. If equipped on late-model vehicles, loosen and remove the tank plastic shield.
  4. Loosen the retaining clamp and disconnect the tank filler hose from the tank neck.
If fuel and vapor hoses or pump/sending unit wiring can be accessed at this time, they may be tagged and disconnected. If not, wait for the retaining straps to be loosened and lower the tank slightly for access.
  1. Tag and disconnect and accessible wiring or hoses from the top of the fuel tank.
  2. Have and assistant support the fuel tank, then remove the fuel tank-to-vehicle straps and, if equipped, the isolation strips. If no assistant is available, position a floor jack to support the tank while the straps are removed.
  3. Lower the tank slightly, then remove the sending unit or sending unit/pump wires, hoses and ground strap. Be sure to label all connections to ease installation.
  4. Carefully lower the fuel tank from the vehicle and store in a safe place.
To install:
  1. Raise the tank partially into position in the vehicle. If you are working without an assistant, you may wish to loosely install one of the retaining straps and use a floor jack to support the tank at an angle so there is access to the sending unit or sending unit/pump assembly (as applicable).
  2. Connect the fuel/vapor hoses and wiring to the top of the fuel tank, as tagged during removal.
  3. Carefully raise the fuel tank so it is fully into position and loosely secure the retaining straps. Make sure the wires and hoses are not pinched or damaged when raising the tank. Also, be sure that the isolation strips (if used) are positioned between the retaining straps and the fuel tank.
  4. It may be easier to connect the fuel filler hose to the tank neck at this time. If desired, connect the hose and secure the clamp.
  5. Tighten the fuel tank retaining strap fasteners to specification. Tighten the strap nuts to 33 ft. lbs. (45 Nm).
  6. If not done earlier, connect the tank filler hose to the tank neck and secure using the clamp.
  7. If equipped, install and secure the tank plastic shield.
  8. Remove the jackstands and carefully lower the rear of the truck.
  9. Refill the fuel tank and install the filler cap, then check for leaks.
  10. Connect the negative battery cable.
Equipped With Shield Package
  1. Properly drain the fuel tank, then disconnect the negative battery cable.
  2. Raise and support the rear of the truck safely using jackstands.
  3. Remove the shield forward support and bracket.
  4. While supporting the shield and tank assembly with the help of both an assistant and a floor jack, remove the remaining bolts holding the assembly to the frame, then lower it sufficiently for access to the hoses and wires.
  5. Tag and disengage the hoses and wires from the sending unit assembly.
  6. Carefully lower the fuel tank and shield from the vehicle, then if necessary for service or replacement, separate the tank from the shield.
To install:
  1. If separated, install the tank to the shield.
  2. Carefully raise the tank and shield assembly partially into position with the help of an assistant and a floor jack.
  3. Connect the wiring and hoses to the sending unit assembly, as tagged during removal.
  4. Raise the tank and shield assembly fully into position, then secure to the frame using the lower retaining bolts.
  5. Install the shield forward support bracket.
  6. Remove the jackstands and carefully lower the rear of the truck.
  7. Refill the fuel tank and install the filler cap, then check for leaks.
  8. Connect the negative battery cable.
  any question I can send some diagrams

Sep 14, 2008 | 1998 Oldsmobile Bravada

Not finding what you are looking for?
1997 Chrysler Town & Country Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...