Question about Nissan Murano

1 Answer

Have an 05 murano and the supplemental restraint system light has come on and stays on while in the vehicle. how can i reset or fix this problem?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 39 Answers

I dont think you can reset it i think it is your air bag module and they run somewhere in the $600 range.I ran into this problem on another murano, but the customer did not want to fix it. Do you still have warranty on this vehicle.

Posted on Sep 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the air bag sensors on a 2000 Lincoln towncar


Sensor - Front Crash Removal
WARNING: Vehicle sensor orientation is critical for proper operation. If a vehicle equipped with an air bag supplemental restraint system (SRS) is involved in a collision, inspect the sensor mounting bracket and wiring pigtail for deformation. Replace and properly position the sensor or any other damaged supplemental restraint system (SRS) components whether or not the air bag is deployed.
WARNING: Always wear safety glasses when repairing an air bag supplemental restraint system (SRS) vehicle and when handling an air bag module. This will reduce the risk of injury in the event of an accidental deployment.
WARNING: To reduce the risk of personal injury, do not use any memory saver devices.
NOTE: The air bag warning lamp illuminates when the RCM fuse is removed and the ignition switch is ON. This is normal operation and does not indicate a supplemental restraint system (SRS) fault.
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
NOTE: Repair is made by installing a new part only. If the new part does not correct the condition, install the original part and perform the diagnostic procedure again.
  1. Depower the system. For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering in this section.
  1. Remove the radiator upper sight shield (8C291).
  1. Remove the air bag sensor.
    1. Disconnect the air bag sensor electrical connector.
    1. Remove the three screws.
    1. Remove the air bag sensor.
    2. SECTION 501-20B: Supplemental Restraint System 2000 Town Car Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/10/2004 Sensor - Side Crash Removal
      WARNING: Vehicle sensor orientation is critical for proper system operation. If a vehicle equipped with an air bag supplemental restraint system (SRS) is involved in a collision, inspect the sensor mounting bracket and wiring pigtail for deformation. Replace and properly position the sensor or any other damaged supplemental restraint system (SRS) components whether or not the air bag is deployed.
      WARNING: Always wear safety glasses when repairing an air bag supplemental restraint system (SRS) vehicle and when handling an air bag module. This will reduce the risk of injury in the event of an accidental deployment.
      WARNING: To reduce the risk of personal injury, do not use any memory saver devices.
      NOTE: The air bag warning lamp illuminates when the RCM fuse is removed and the ignition switch is ON. This is normal operation and does not indicate a supplemental restraint system (SRS) fault.
      NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
      NOTE: Repair is made by installing a new part only. If the new part does not correct the condition, install the original part and perform the diagnostic procedure again.
      NOTE: Left side is shown, right side is similar.
      NOTE: The side crash sensors are located under the carpet beneath the front seats.
      1. Position the seat to gain access to all fasteners.
      1. Depower the system. For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering in this section.
      1. Remove the front seat. For additional information, refer to Section 501-10 .
      1. Remove the safety belt anchor bolt cover.
      1. Remove the bolt and the safety belt anchor.
      1. Remove the front and rear door scuff plates.
      1. Remove the lower B-pillar trim panel.
      1. Remove the carpet to access the side crash sensor.
      1. Remove the side crash sensor.
        1. Remove the retaining bolts and position the side crash sensor in order to disconnect the electrical connector.
        1. Disconnect the electrical connector.
        1. Remove the side crash sensor and bracket.

Dec 16, 2015 | 2000 Lincoln Town Car

2 Answers

Airbag light came on my 05 f 150 code is 33 how do I fix it


Check with dealer might be a recall for defective srs.

Apr 18, 2015 | Cars & Trucks

1 Answer

2006 toyota tacoma srs light stays on where is relay


Hi Keith,

"SRS" stands for "Supplemental Restraint System". This includes your airbags and your seatbelt pre-tensioners. The only way to find out why the light is on is to scan your airbag module and retrieve the fault codes that will be stored to let you know which part of the system is failing.

There are a few Technical Service Bulletins (TSBs) for the SRS in your vehicle, however none of them address any concerns with sysem failure or the light illuminating. They have to do with proper service proceedures to prevent accidental airbag deployment, disposal of deployed airbag parts, notification to the service technicians that they MUST replace an entire harness to fix wiring problems in the SRS and that wiring repairs are NOT to be made, etc..

Please also note that if the SRS light is on, the safety systems in your vehicle WILL NOT WORK in the event of an accident. It is highly recommended that you get this properly diagnosed and repaired by a trained service technician as soon as possible. Unless you have had specific training for the supplemental restraint system in your vehicle, I DO NOT recommend trying this at home.

Nov 06, 2011 | 2006 Toyota Tacoma

1 Answer

What does SRS lit up on the dashboard mean. 1995 accord wagon.


the SRS stands for Supplemental Restraint System. Most people call it the air bags but the SRS system includes all of the sensors and control units for air bags, seat belt pre-tensioners and passenger detection systems on cars that are equiped with themeach time you start the car up the SRS control unit will do a self-test of the system to make sure all of the sensors are working properly. The SRS light will stay on while that test is conducted. If all is well and everything passes the on-board test the light will go out in about 7 seconds. If something is wrong the light will stay on.whenever a failure is detected for any reason,the SRS light is turned on and the system is shut off. The air bags will not be deployed when the SRS light is on.They call it a Supplemental Restraint System because your seat belts are your primary restraint system.

Mar 22, 2011 | Honda Accord Cars & Trucks

1 Answer

Where is the switch to disable the passenger airbag on a 2003 ford taurus


Supplemental Restraint System (SRS) Depowering and Repowering

Depowering Procedure

WARNING: Always wear safety glasses when repairing an air bag supplemental

restraint system (SF3) vehicle and when handling an air bag module. This will reduce

the risk of injury in the event of an accidental deployment.

WARNING: Never probe the connectors on the airbag module. Doing so can result in

air bag deployment, which can result in personal injury.

WARNING: To reduce the risk of personal injury, do not use any memory saver

devices.

NOTE: Ifa seat equipped with a seat mounted side airbag and or a safety belt

pretensioner (if equipped) system is being serviced, the supplemental restraint system

(SES) must be depowered.

NOTE: The air bag warning lamp illuminates when the RCM fuse is removed and the

ignition switch is ON. This is normal operation and does not indicate a supplemental

restraint system (SRS) fault.

NOTE: The SRS must be fully operational and free of faults before releasing the vehicle

to the customer

1. Turn all vehicle accessories OFF.

2. Turn the ignition switch to OFF.

3. At the central junction box (Cm), located below the LH side of the instrument panel,

remove the cover and the restraints control module (RCM) fuse F223 (lOA) from

the CTh. For additional information, refer to the Wiring Diagram Manual.

4. Turn the ignition ON and visually monitor the air bag indicator for at least 30

seconds. The air bag indicator will remain lit continuously (no flashing) if the correct

ROsI fuse has been removed, If the air bag indicator does not remain lit

continuously, remove the correct RCM fuse before proceeding

5. Turn the ignition switch to OFF.

6. WARNING: To avoid accidental deployment and possible personal injury, the

backup power supply must be depleted before repairing or replacing any front or

side air bag supplemental restraint system (SRS) components and before set-ricing,

replacing, adjusting or striking components near the front or side air bag sensors,

such as doors, instrument panel, console, door latches, strikers, seats and hood

latches.

To deplete the backup power supply energy, disconnect the battery ground cable

and wait at least one minute. Be sure to disconnect auxiliary batteries and power

supplies (if equipped).

Disconnect the battery ground cable and wait at least one minute.

Repoweri.ng Procedure

1. WARNING: The restraint system diagnostic tool is for restraint system service

only. Remove from vehicle prior to road use. Failure to remove could result in

injury and possible violation of vehicle safety standards.

Make sure all restraint system diagnostic tool(s) that may have been installed during

the repair have been removed from the vehicle and all SRS components are

connected.

2. Turn the ignition switch from OFF to ON.

3. Install the ROsI fuse F2.23 (lOA) to the DB and install the cover.

4. WARNING: Be sure that nobody is in the vehicle and that there is nothing

blocking or set in front of any air bag module when the battery ground cable is

connected.

Connect the battery ground cable.

5. Prove out the supplemental restraint system (SRS) as follows:

Turn the ignition key from ON to OFF. Wait 10 seconds, then turn the key back to

ON and visually monitor the air bag indicator with the air bag modules installed. The

air bag indicator will light continuously for approximately six seconds and then turn

off. If an air bag supplemental restraint system (SF3) fault is present, the air bag

indicator will:

- failto light.

- remain lit continuously.

- flash.

The flashing might not occur until approximately 30 seconds after the ignition switch

has been turned from the OFF to the ON position. This is the time required for the

restraints control module (RCM) to complete the testing of the SRS. if the air bag

indicator is inoperative and a SRS fault exists, a chime will sound in a pattern of 5

sets of 5 beeps. If this occurs, the air bag indicator and any SRS fault discovered

must be diagnosed and repaired.

Jan 12, 2011 | 2003 Ford Taurus

1 Answer

Replacing the agnition switch how to?


SECTION 211-05: Steering Column Switches 2001 Focus Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 09/15/2004 Ignition Switch Removal
  1. Depower the supplemental restraint system (SRS). For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering (501-20B Supplemental Restraint System, GENERAL PROCEDURES).
  1. Detach the instrument panel lower panel.
    1. Remove the screws.
    1. Release the fastener.
    e0001946.jpg
  1. Remove the instrument panel lower panel.
    • Disconnect the hood release.
    • Disconnect the data link (DLC) electrical connector.
    e0009940.jpg
  1. Detach the steering column upper shroud.
    • Using a thin bladed screwdriver, release the two clips (one each side).
    e0000671.jpg
  1. Remove the steering column lower shroud.
    1. Release the steering column locking lever (if equipped).
    1. Remove the screws.
    • Remove the ignition key.
    e0000670.jpg
  1. Disconnect the electrical connectors.
    • Disconnect the ignition switch electrical connector.
    • Disconnect the turn signal/flash-to-pass switch electrical connector.
    e0001776.jpg
  1. Remove the ignition switch.
    • Release the clips.
    e0000394.jpg
Installation
  1. To install, reverse the removal procedure.
  1. Repower the supplemental restraint system (SRS). For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering (501-20B Supplemental Restraint System, GENERAL PROCEDURES).

2010&c18=modelyear&c20=g17614&c35=wsm%2cignition%20switch%2cs1y%2c211-05%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=lan&hp=n&[aqe]

Apr 01, 2010 | 2001 Ford Focus

2 Answers

What does the SRS and VSA lights on the dashboard mean?


SRS - Supplemental restraint system.

VSA - Vehicle stabitity assist.

Feb 16, 2010 | 2002 Acura 3.2CL

3 Answers

HOw do you reset the SRS display


The light is on to indicate a fault in the airbag system, the light will remain on until the fault is repaired, also understand as long as the SRS waring indicator is on the airbag system is disabled

Oct 12, 2008 | 2001 Honda CR-V

1 Answer

SRS


SRS stand for Supplymentary Restraint System, The purpose of the SRS light on your instrument panel is to alert you of a potential problem with your supplemental restraint system. It should blink seven times when you turn the ignition switch to ON or START and go OFF. A possible fault in the system can lead to any of the following: (a) The light does not come on when you turn the ignition ON. (b) The light stays on after the engine starts. (c) The light comes on while you are driving. Apart from the conventional causes of these faults (faulty airbag system), majority of the light indicator problem has been attributed to ignorance while fixing or repairing mechanical and/or wiring systems within the vehicle. If the SRS indicator light alerts you to a problem, have the supplemental restraint system inspected as soon as possible. If you ignore this indication, the airbags might not inflate when you need them. Likely Causes:
  • Steering wheel modifications
  • Faulty driver/passenger seat sensors for your airbag system (located under the seats)
  • Faulty seat belt mechanism
  • Tampered system components or wiring (e.g battery jumpering)
* Sometimes, a little adjustment of your seat belts and/or seat positions might fix the indicator problem over time (if the sensors are not faulty).
Precautions:
  • Do not modify your steering wheel or any other part of the supplemental restraint system. Modifications could make the system ineffective.
  • Do not tamper with the system's components or wiring. This could cause the airbags to inflate inadvertently, possibly injuring someone very seriously.
  • Tell anyone who works on your vehicle that you have a supplemental restraint system. Failure to follow the procedures and precautions in the official service manual could result in personal injury or damage to the system.
  • If all sensors are ok, the system can be reset using appropriate tools; refer to specially trained technicians.
Cheers Fred Omorogbe (reference: https://techinfo.honda.com/rjanisis/pubs/om/PA9696/PA9696A00015A.pdf)

Sep 08, 2008 | 2001 Mercedes-Benz E-Class

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...