Question about 2001 Daewoo Lanos

1 Answer

Head screws Whats the turok on the head srews?

Posted by on

  • nazarkamal Oct 17, 2008

    when i gets start of my lanos 2001 it gets very very hot inside engine and this cause air conditioning not cooling at all ...Compresser becomes very hot ..just within first 5 mins of starting the Car.



1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

2001 Daewoo Lanos Cylinder Head Bolt Torque Specs
Torque bolts in sequence
(looking down on the engine from front of car)

belts 1 3 9 5 7 trans
belts 2 4 10 6 8 trans

Step 1: 18 ft.lbs. (25 Nm)
Step 2: Plus 60 degrees
Step 3: Plus 60 degrees
Step 4: Plus 60 degrees
Step 5: Plus 10 degrees

Posted on Dec 15, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Engine won't running after replaced head gasket

did you change the timing belt ..when the head gaskets are replaced ,,the vehicle got so hot it stretched it out of time ..It is mainly a strong rubber band in my opinion ,,but it will not crank if the belt is out of time totally or if the belt is broke ..takes me as a mechanic 4 hours to do this job

Oct 27, 2013 | 2001 Toyota Corolla

1 Answer

How to change glow plugs on a 05ford courier

To replace the glow plugs they are srewed into the head just like a spark plug but with a lot smaller hex drive . Just unscrew them and screw in the new ones. You will have to remove a connecting bar or wire to each one first.

Feb 25, 2013 | Cars & Trucks

1 Answer

How do i remove the alternater from my 1991 Honda Accord

In front of your engine where the belts are,You'll see that there's 3 belts. Those belts consists of your power steering,ac and of course...your alternator.. First, you'll have to take your P.S belt off by loosening up two main metric size 14 screws from your power steering pump. Once you've done that, you see the tightening srew head on top of the pump..yeah turn that to the left and you'll have room to move the pump up and down...move it down so that you can have enough room to take the P.S belt off.. Next look at your A/c unit and do the same. Last but not least.....loosen up the two screws from your alternator and move the unit towards the front of the car and remove the belt....Do the opposite to rap it up...Hope this helps!! GL!!

Feb 09, 2011 | 1991 Honda Accord

2 Answers

How do you change a turn signal bul on a 90 chevy

there should be an access panel in the trunk.

Apr 18, 2010 | 1990 Chevrolet Lumina

1 Answer

Where is the throttle sensor located on a 1995 cirrus cxi and whats the price of one

the tps is on the side of the throttle body,has 1 plug in connector ,2 screws holding it on , i believe they are torx head screws

Jan 31, 2010 | 1995 Chrysler Cirrus

1 Answer

Replace daytime running light for 2005 dodge

There are three flat head srews on the head lamp housing under the hood you have to remove all three then the lense housing is easily removed and the actual lamp is twist locked losen twist lock lefty lose tighty right
and the head lite is a plug in type remove old one istal new one and presto follow the rest in reverse.

Jan 03, 2010 | 2005 Dodge Caravan

1 Answer

Headlights beams not not aligned


Aug 03, 2009 | Mazda MAZDA3 Cars & Trucks

1 Answer

1991 front speaker replacement

ok, i don't have pictures but i'll see if i can help. usually the covers over the speakers either have two srews holding them down or they just need a flat screwdriver to pry them up. if they have srews, you'll need a very small screwdriver to fit in between the window and speaker cover. some screws are star screws which need special star tool to get out. but most are philips screws. if you can get the covers off, you'll see the speakers, now you'll just need to take the two screws holding them down, out.pull the speaker up and out, unhook the wires and replace them. if you have the kind of covers that just pry off, just be careful not to hit the glass, i put up a piece of cardboard to be safe..i hope this helps you.

Nov 28, 2008 | 1991 Toyota Corolla

1 Answer

Ignition switch replacement 1992 Toyota Pickup How to

i had to remove the steering column and use a vice-grip to remove those bolts. i replaced them with allen bolts.

Aug 10, 2008 | 1992 Toyota Pickup

2 Answers

Discs won`t come off Honda

Did you remove the two phillip head retaining screws that hold the rotor to the hub? Also, if there is alot of corrosion around the center of the hub, the rotor might be stuck in place. In that case, you'll have to tap the rotor with a hammer to break it free.

May 21, 2008 | 1998 Honda Accord

Not finding what you are looking for?
2001 Daewoo Lanos Logo

544 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

78919 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides