Question about 1994 Dodge Intrepid

1 Answer

Reset button were is the reset button

Posted by on

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

There is not a reset button to reset you computer disconnect your negative cable from the battery for about 10 minutes. it will be hard to start at first because the computer is resetting.

Posted on Oct 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford explorer trac 2007 change the oil and filter and now have a wrench light on ,how resolve the problem


Sounds like you need to reset your Oil life/ maintenance reminder light. (also, double check your oil level)

To reset Oil life on a standard dash stlye:
1. pres and release the TRIP/RESET button until the message center displays SETUP MENU HOLD RESET
2. Press and hold the TRIP/RESET button for 2 seconds until the message center displays RESET FOR SYS CHECK
3. press and hold the TRIP/RESET button for 2 seconds until the message center displays OIL LIFE xx% RESET IF NEW
4. Press and release the TRIP/RESET button until the message center displays HOLD RESET IF NEW OIL
5. Press and hold TRIP/RESET button for 2 seconds and release to reset oil life to 100%
6. Message center will briefly display OIL CHANGE SET TO 100%


With a message center cluster the procedure is as follows:
1. press and release SETUP button until message center displays PRESS RESET TO BEGIN SYSTEM CHECK
2. Press and release RESET button until the message center displays HOLD RESET IF NEW OIL
3. Press and hold RESET button for 2 seconds and release to reset the oil life to 100%
4. The message center displays SETUP MENU HOLD RESET


Hope this is what you need/ are looking for. Goodluck & let me know how it goes, or if you have a different problem.

Nov 03, 2013 | 2006 Ford Explorer

Tip

Ford-Lincoln service light 1988-01


LS

2000-01

To reset CHANGE OIL SOON/OIL CHANGE REQUIRED message on the Message Center, press the STATUS control to access the System Check mode. Press the RESET button to display OIL LIFE _% RESET FOR NEW. Press and hold the RESET button until OIL LIFE IS 100% is displayed.


Mark VIII


1993-97

When "CHANGE OIL SOON" or "OIL CHANGE REQUIRED" is displayed on the Message Center, turn the ignition on. Press and hold "OIL CHANGE RESET' or the "RESET" button until "OIL LIFE RESET TO 100%" is displayed on the Message Center.


Continental


1989-94

When "SERVICE" is illuminated, on the Message Center, press the "SYSTEM CHECK" button on the right of the display. Then press the "RESET" button. The "SERVICE" symbol and mileage will start to flash. Next, press the "SYSTEM CHECK" and "RESET" buttons at the same time. The display will show "7,200 miles/11,580 km" and will count down from there as long as the buttons are depressed. Release the buttons at the desired service interval.


Continental


1988

When "SERVICE DUE" is illuminated on the Message Center, press the "CHECK OUT" button located below the display. Then press the "RESET" button. The display should now read "SERVICE DONE?" Next, press the "CHECK OUT" button and "RESET" buttons at the same time. The display will show "7,200 miles/11,580 km" and will count down from there as long as the buttons are depressed. Release the buttons at the desired service interval.







on Dec 07, 2009 | Ford Lincoln Continental Cars & Trucks

1 Answer

Is there a reset button for this car


A reset button for.....???
Just about the only thing that will have a reset button is the tripometer. There is no reset button for the ignition. There is no reset button for the fuel pump. The is not reset button for the power seats, mirrors, windows or locks. Seats, windows and locks though will have a breaker in the interior fuse panel. If the breaker has tripped all you do is unplug the breaker and plug it back in.
But it would really help me help you if I was to know what you need "reset".

Nov 05, 2011 | 1997 Chevrolet Suburban

2 Answers

How can I reset service light on 2008 Volvo V50


OTE: If the service interval indicator flashes it may be caused by one of the service interval indicator parameters not being programmed. This can only be carried out using suitable diagnostic equipment. Always check for any stored trouble codes as this may affect the resetting of the service interval indicator.
Ensure all doors are closed. Turn ignition key to position I. Press and hold reset button [A] 104667 07, 116126 07 Immediately turn ignition key to position II (within 2 seconds). Keep button [A] depressed until service message has been reset. A yellow warning light [B] will illuminate when it is time to release button [A]. Release reset button [A] within 4 seconds. There will be an audible signal when reset is complete. If reset button is not released within 4 seconds, the service interval indicator will not be reset.
RESET BUTTON IS TRIP BUTTON

Jun 08, 2011 | 2008 Volvo V50

1 Answer

Need to reset the Change Oil Light on a 2007 Mercury Grand Marquis


SWITCH IGNITION ON.ENGINE OFF. PRESS AND RELEASE SETUP BUTTON.PRESS SELECT TO BEGIN SYSTEM CHECK IS DISPLAYED. PRESS AND RELEASE SELECT BUTTON WHEN OIL LIFE PRESS RESET IF NEW OIL IS DISPLAYED PRESS AND HOLD RESET BUTTON FOR 2 SECONDS. OIL LIFE XXX% HOLD RESET IF NEW OIL IS DISPLAYED. PRESS AND HOLD RESET BUTTON FOR 3 SECONDS UNTIL OIL LIFE START VALUE SET TO 100 % IS DISPLAYED. SWITCH OFF IGNITION.------- NOTE THE SETUP BUTTON AND SELECT BUTTON ON STEERING WHEEL CONTROL PAD THE RESET BUTTON IS ON DASH THERE IS FOUR LITTLE BUTTONS ON DASH SECOND BUTTON IS THE RESET BUTTON.

Jun 05, 2011 | Mercury Grand Marquis Cars & Trucks

1 Answer

I had my oil changed in October after the "oil


Try this procedure and let me know if this does not work;

Turn the ignition switch to the "On" position but do not start the engine.

1. Press the Trip/Reset button until "Setup Menu Hold Reset" is displayed.

2. Then press and hold down the Trip/Reset button for approximately 2 seconds until "Reset For System Check" is displayed then release the Trip/Reset button.

3. Then immediately press and hold down the Trip/Reset button again for approximately 2 more seconds until "OIL 100% RESET IF NEW" is displayed then release the Trip/Reset button.

4. Then immediately press the Trip/Reset button once to display "HOLD RESET IF NEW OIL" then release the Trip/Reset button.

5. Then immediately press and hold the Trip/Reset button again for approximately 2 seconds until "OIL LIFE SET TO 100%" is displayed.

Turn off the ignition switch, and then start the engine to verify that the reset procedure did work, and you might have to repeat the procedure if the Trip/Reset button is not pushed fast enough, or it is not held down long enough, or it is held down too long during the reset procedure, and it may take a few attempts to be successful.

Nov 11, 2010 | 2006 Ford Explorer

2 Answers

How do I get the "change oil" message off my 2008 f 450 superduty?


Message center cluster
#1 press and release setup button until mess. cntr. displays"press reset to begin system check"
#2press and release reset button until cntr. displays"hold reset if new oil"
#3press and hold reset button for 2 sec. and release oil life should read 100%
#4 center displays"setup menu hold reset"

base cluster
#1 press and release trip/reset button until mess. cntr. displays"setup menu hold reset"
#2press and hold trip/reset button 2 sec. until mess cntr. displays"reset for system check"
#3 press and hold trip/reset button 2sec. until mess. cntr. displays"oil life XX% reset if new"
#4 press and release trip/reset button until mess.cntr.displays"hold reset if new oil"
#5 press and hold trip/reset button for 2 sec.and release to reset to 100%
#6 mess. cntr. breifly displays oil change set to 100%.

HOPE THIS HELPS

Feb 10, 2010 | 2008 Ford F 250 Super Duty 4WD

2 Answers

Changed the oil in a 2006 mountaineer but the change oil warning won't go off


You need to reset the oil light using the reset button on the steering wheel. Press the set up button to access the system check mode. press and release the reset button until the display reads "oil life hold reset new". PRess and hold the reset button for two (2) seconds until "if new oil hold reset" is displayed. Press and hold the reset button until "oil life set to 100" is displayed.

Dec 05, 2009 | 2006 Mercury Mountaineer

3 Answers

How do i switch off service now light on my vw golf 53 plate


Courtesy www.synthetic-direct.ca:

To reset the message displays, turn the ignition switch on. Press and hold the odometer reset button “A” located below the speedometer. Turn off the ignition while holding the button. “OEL” will display on the indicator. Press and hold the lower digital clock reset button or the analog clock reset button “B” until five dashes appear in the display.
If needed, next press the odometer reset button until IN 01 is displayed and then press the clock reset button until five dashes appear. If needed, next press the odometer reset button until IN 02 is displayed and then press the clock reset button until five dashes appear.
To exit reset mode, turn ignition switch on and when IN 01 appears, turn ignition off.



Jul 24, 2009 | Volkswagen Golf Cars & Trucks

1 Answer

How to i turn off the service now light on a 03 vw golf


To reset the message displays, turn the ignition switch on. Press and hold the odometer reset button "A" located below the speedometer. Turn off the ignition while holding the button. "OEL" will display on the indicator. Press and hold the lower digital clock reset button "B" until five dashes appear in the display. If needed, press the odometer reset button until "IN 01" appears and then press the clock reset button until five dashes appear. If needed, press the odometer reset button until "IN 02" is displayed and then press the clock reset button until five dashes appear. To exit reset mode, turn the ignition switch on and when "IN 01" appears, turn the ignition switch off.



1. Switch ignition ON.
2. Press and hold odometer reset button below speedometer.
3. Switch ignition OFF and release odometer reset button. OEL will now
display.
4. Press and hold the lower digital clock set button or the analog clock set
button until five dashes (-----) appear in display.
5. If necessary, pree odometer reset button to proceed to the IN 01 display
(15,000 mile maintenence) and reset using the clock button.
6. If necessary, repeat procedure to reset IN 02 (30,000 mile maintenence)
display.
7. To end reset mode: switch ignition ON; when display IN 01 appears, switch ignition OFF.

Thanks for using FixYa - a FixYa rating is appreciated for taking the time to answer your FREE question.

Mar 19, 2009 | 2000 Volkswagen Golf

Not finding what you are looking for?
1994 Dodge Intrepid Logo

Related Topics:

272 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...