Question about Mitsubishi Galant

1 Answer

Galant 2005 Power lock keep clicking when driving car.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Is it only clicking when its turnd an driveing if so this could mean you will need a cv joint on what ever side the noise is comeing from

Posted on Sep 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mitsubishi Galant 2005 4dr blower fan has no power


The radiator fan will not normally have power. It is only when the engine coolant thermostat detects high temperature it sets on the fan relay which starts the fan. So it is likely the thermostat or the fan relay are faulty.

Aug 31, 2014 | 2005 Mitsubishi Galant

2 Answers

Why does my galant make a screaming noise when i start my galant


could be worn drive belts, try sprayin the alternator etc drive belt with wd40 before starting and see if no screaming ,if no sctreaming change belts, as these are never changed at the requried intervals

May 19, 2014 | 2005 Mitsubishi Galant

1 Answer

2002 mitsubishi galant doesn't start and my power windows and locks arent working either


If you hear a click then it is the starter motor, these often stick on all cars & can be renedied by smacking it with a hammer a few times, if you hear nothing at all then it is probably the battery, first off remove it from the vehicle & charge it overnight 24 hrs + to see if this remedies the problem, if the car starts & drives, then my advice is to keep an eye on the volt meter & buy a cheap hand held volt meter to frequently check the voltage of the battery when at rest (with the car turned off) the voltage should be between 12.01-12.86V the check it with the vehicle running, If you get a reading under 12.86V with the engine running then your alternator has ceased to work & will need replacing, Hope this helps.

Sep 13, 2012 | 2002 Mitsubishi Galant

1 Answer

Where are the timing marks located on a Mitsubishi 2005 Galant 2.4 engine?


They are on the crank pulley and on the camshaft drive pulleys.

Jun 05, 2012 | 2005 Mitsubishi Galant ES

1 Answer

I was driving my 05 gallant my power steering belt broke I replaced it but my car wont start now


Is the pump free if not the car can not turn over with the speed it needs to crank

Dec 01, 2011 | 2005 Mitsubishi Galant

1 Answer

2004 Mountaineer: When my 2005 Mercury Mountaineer is running the po...


My husband had the same problem with his 02 Mountaineer about 6 months ago. I read somewhere that if you take WD40 & spray the door locks it should stop. We tried it & so far it's worked. Good luck!

May 17, 2010 | 2004 Mercury Mountaineer

1 Answer

Change timing belt galant 04 mivec 2.4


49885ff.gif
Timing belt “B” (balancer belt) and related components—2004–2005 Galant and 2004–2005 Lancer 2.4L engine


  1. Disconnect the negative battery cable. Remove the engine under cover.
  2. Remove the crankshaft damper pulley.
  3. Disconnect the control wiring harness connector, battery wiring harness connector and connector bracket to engine mounting insulator.
  4. Remove the harness bracket. Remove the upper timing belt cover. Remove the water pump pulley. Remove the idler pulley.
  5. Remove the auto tensioner. Remove the lower timing belt cover.
  6. Turn the crankshaft clockwise and align each timing mark to set the number one piston to TDC of its compression stroke.
  7. Remove the timing belt under cover rubber plug and then install special tool MD998738. Screw the special tool until it contacts the timing belt tensioner arm.

    NOTE The special tool must be screwed in gradually at the rate of a 30 degree turn per second. If it is screwed in all at once, the timing belt tensioner adjuster rod will not easily retract and the tool may bend.

  8. Gradually screw in the special tool and then align the timing belt tensioner adjuster rod set hole “A” with the timing belt tensioner adjuster cylinder set hole “B”.
  9. Insert a wire or pin in the set holes to lock the assembly in place. After removing the special tool, loosen the timing belt tensioner pulley mounting bolts and remove the timing belt. If the belt is being reused be sure to mark the direction of rotation (clockwise) on the belt.
  10. Remove the timing belt tensioner pulley, tensioner arm and adjuster.
  11. Remove the timing belt idler pulley. Remove the timing belt lower cover bracket. Remove the crankshaft position sensor.
  12. Remove the crankshaft pulley center bolt and washer. Remove the drive sprocket. Remove the crankshaft angle sensing blade.
  13. Remove the balancer timing belt tensioner. Remove the timing belt “B” (balancer belt) from its mounting.


284eb62.gif
Timing belt tensioner adjuster rod set hole “A” and cylinder set hole “B”—2004–2005 Galant and 2004–2005 Lancer 2.4L engine

To install:


78b2d67.gif
Belt tension checking—2004–2005 Galant and 2004–2005 Lancer 2.4L engine


b8fcecc.gif
Cylinder block plug location—2004–2005 Galant and 2004–2005 Lancer 2.4L engine


bad1ef9.gif
Timing belt sprocket alignment—2002–2004–2005 Galant and 2004–2005 Lancer 2.4L engine

Feb 27, 2010 | 2004 Mitsubishi Galant

1 Answer

I have a 2005 galant, when I try to put my car in drive it would stop at neutral. I turned the car off and turn it back on and then in went into drive. I need help!


Shift linkage attatches to trans on drivers side of trans make sure its connected with no obstructions. It could be related to your neutral safety switch which keeps the car from starting while it's in gear

Sep 09, 2009 | 2005 Mitsubishi Galant

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...