Question about 1999 Jeep Grand Cherokee

1 Answer

Remove head light to replace bulbs

II have a 1999 Jeep Grand Cherokee Limited 4.7 power stoke. I need to replace the low beem bulb how do I remove the head light assembly to change the bulb???

Posted by on

  • Anonymous Mar 21, 2014

    replacing light bulb

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 475 Answers

You have to be careful-the whole assembly snaps in and out

Posted on Oct 06, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace License Plate Bulb '96 Jeep Grand Cherokee Limited


Hi Timmy:

Check this procedure from Repair manual...


LICENSE PLATE LAMP - REMOVAL
(1) Remove screws and license plate lamp visor from liftgate (Fig. 10).
(2) Remove bulb from lamp socket.

INSTALLATION
(1) Install a bulb in lamp socket.
(2) Position license plate lamp visor on liftgate and install screws (Fig 10).


4_28_2012_5_22_57_pm.jpg


Hope this helps.

Apr 28, 2012 | 1996 Jeep Grand Cherokee

1 Answer

97 Jeep Grand Cherokee V8 Low beams will now work, high beams do. We replaced the bulbs and the low beams worked for a while and then didn't again, husband took out passenger side bulb and put it back...


Make sure that you are using the head light bulbs for that particular make/model if the bulb number is wrong then the intensity is wrong too. Now a day there are many diffrent numbers of bulbs in the market according to vehicle.

Sep 08, 2011 | 1997 Jeep Grand Cherokee

1 Answer

1999 Jeep Grand Cherokee Limited - Break lights will work if the head lights are turned off, but when i turn the lights on the break lights won't work.


If you recently had a brake light bulb changed, you may have one or more brake bulbs installed wrongly on your jeep, shorting out when the lights are turned on.

Oct 19, 2010 | 2000 Chrysler Concorde

1 Answer

Brake light bulb replacement for 2002 jeep grand


After removing the 2 expose screws. You will need to carefully & firmly rotate the assembly away from the vehicle until it releases from the ball pin socket that holds it in back.
The unit contain 3 same exact bulb type, can be removed by turning them counter-clockwise 1/4 turn.

Jan 21, 2010 | 2002 Jeep Grand Cherokee

2 Answers

I only have high beems, I have replaced the bulbs and checked the fuses


check light switch,contacts brun out due to heat,we alway use low beams, that y high beam still work,they dont get used as often,and contacts melt,well good luck.

Oct 06, 2009 | 1998 Jeep Grand Cherokee

1 Answer

Tail lights 99 jeep grand cherroke limited


have you checked the bulb sockets to see if they are burnt or corroded sometime i see that the plastic melts around the contacts where the socket twists into the housing. if your lucky you might get away with replacing just the socket for the brake/running light bulb. but if it is too melted your most likely going to need a new housing

Jan 06, 2009 | 1999 Jeep Grand Cherokee

1 Answer

1993 jeep grand cherokee limited no running lights/tail lights.


Id look at the headlight switch and do some voltage tests to see whats coming out of there. Pay close attention to any wires which look like someone was in there already.People can mess stuff up faster and better than the vehicle can by itself!

Jan 04, 2009 | 1993 Jeep Grand Cherokee

1 Answer

How do I change the parking lightbulb?


In prying, I hope that you removed the screws first!!! Likely, there is one that you missed. Park light& turn signal light are connected to the housing around the headlight. When removing it, make sure you don't turn the adjusting screws for the headlight itself! The light socket turns 1/4 turn to left to disengage it. Be careful not to break bulb or you will cut yourself.. On some bulbs, match the small nubs in the sides of the brass part of the bulb to the slots in the socket. they are not the same (one high, one low) Use wd40 if socket is rusted to bulb.
That's about all I can tell you without going there & doing it for you!!!
Good luck!

Dec 26, 2008 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
1999 Jeep Grand Cherokee Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...