Question about 1988 Ford Mustang

1 Answer

Head lights When my lights have been on for 10 to 15 mins they start blinking on and off. I have to turn them on and off a couple times before they come back on. This doesnt fix the problem though. I have to put them on brights before this wont happen again. What is going on?

Posted by on

  • kenneth pernell Sep 21, 2008

    Thanks, I thought it was this but wasnt for sure!

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 60,876 Answers

I am a retired Ford dealer technician and I can tell you with 100% certainty that the head light switch is bad.

Posted on Sep 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car stalle Security light on


Try your spare key.It could be that the primary key you have been using needs to be reprogrammed,which can be done by contacting a dealer.Turn the key to the "On" position in order to reset the pass lock system.Wait for fifteen minutes with the key in the "On" position.If the security light disappears, turn the key to the "Accessories" position and wait for a couple of seconds.Turn the key to the "Off" position and take it out from the lock cylinder. Wait a couple of seconds and turn the car on.--------------------------------------------------------------------------------------
Autel MaxiDAS DS708

Jan 08, 2013 | 2001 Pontiac Grand Am SE

1 Answer

1997 Buick theft system light flashes won't start


Try turn key on car but not start for few min.Call dealer for alarms ask ththem.Or get online.

Aug 12, 2012 | 1997 Buick Skylark

1 Answer

Starter ok no blown fuse. all lights working but it wont start. anti theft light blinking fast os soon as you turn it to on. what is the problem.


it is the microchip on your key.. you have to reset the key by sticking it into your ignition and turn it to the run position for 5 mins. at this time the light should stop blinking then turn your key to the off position for 1 sec. repeat six times then your last attempt the car would start guarantee.... notice: as you turn the key to run position the light would blink rapidly for 5mins.. right when it stops turn to the off position for 1 sec.. remember six times..

Feb 01, 2011 | 2004 Ford Explorer

2 Answers

1998 Buick Regal GS, Several problems are


start by checking the front wiring harness for corrosion , best is to do a continuity test on all the wires, look for corrosion in connecting harness, time consuming but the only way

Nov 28, 2009 | 1998 Buick Regal

2 Answers

Changed battery,now it won't start. Tells me anti theft system needs to be reset


Turn your key to ON, Not start, just to on. The theft light should start blinking. Let it blink until it stops. Could take up to 10 minutes or so, let it go until it stops. Then it should be reset.

Nov 16, 2009 | 1998 Pontiac Grand Am

1 Answer

2002 Jeep Liberty headlights blink


I have the same problem. I had it when I turned on my Blinker and turned. When the switch in the steering wheel turn the blinker off it made my head lights blink sometimes. It has to do with the switch that controls the blinker and the head lights. It does not happen all the time.

Aug 18, 2008 | 2002 Jeep Liberty

1 Answer

S2 light blinks (Transmission) and engine light comes on.


change the tempature sensor,it sounds stupid but it fixed my car

Aug 06, 2008 | 1989 Honda Prelude

2 Answers

Reset check engine light


First of all, you should'nt do this unless you know what the problem is.. or what tripped it. I had this problem when my husband and I were replacing a head unit and disconnected the old head unit, a/c and other stuff then turn the car on. This made the light flash. The first time we took it in and got charged $50 to reset it. The second time we did this procedure and it worked.

ECU Resetting Procedures

Timing is extremely critical. If it is NOT DONE within the specify time, the ECU will not reset and the Check Engine Light (CEL) will continue to remain ON.
A stop watch or an analog clock with a second’s needle will be useful.

Reset Check Engine Light Procedures

1. Confirm that accelerator pedal is fully released, turn ignition switch “ON” and wait 3 seconds.
2. Repeat the following steps (2a and 2b) procedures quickly five times within 5 seconds.
2a. Fully depress the accelerator pedal (HARD).
2b. Fully release the accelerator pedal.
3. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 10 seconds until the CEL starts blinking.
4. Fully release the accelerator pedal (while the CEL is still blinking)
5. Wait about 10 seconds.
6. Fully depress the accelerator pedal and keep it for more than 10 seconds.
7. Fully release the accelerator pedal (The CEL light will continue to blink).
8. Turn ignition switch to “OFF” position and now you can start the car. The CEL light should be gone.

If the CEL light continues to remain ON, repeat the above steps. Timing is EXTREMELY critical to resetting the ECU.

-Christine

May 15, 2008 | 2007 Nissan Murano SE

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...