Question about Dodge Cargo

1 Answer

How do you reset a proportioning valve - Cargo Dodge Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 360 Answers

Did you bleed the system out????? usualy you can push the pedal realy hard. but if not theres a small like button on the side of it. its realy hard to push sometimes good luck

Posted on Sep 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I only have front brakes on a 1982 GMC 1500..I get no fluid pressure to the rear. Is there a reset on the proportioning valve?


There is no reset on them. What will work sometimes is to completely remove the brake light switch assembly from the valve and slowly push and release your brake pedal a few times. Then reinsert your brake light switch. If this doesn't work you will have to replace the proportioning valve. New price will likely scare you so head for the scrapyard.

Nov 10, 2014 | Cars & Trucks

2 Answers

How to reset the proportioning valve in brake master cylinder for 1989 Ford F150?


to reset the proportioning valve try bleeding the master by applying pressure and slowly opening one line at the master until the valve centres. you may have to do the same with the other line to get it to centre, sometimes you have to hit the area where the valve is as it may be stuck to get it to move.

Sep 26, 2014 | 1989 Ford F 150

1 Answer

How do i reset a proportioning valve


You replace it. A proportioning valve is what directs the brake fluid where to go. If it malfuctions it must be replaced

Sep 03, 2014 | Cars & Trucks

1 Answer

Proportioning valve stuck


rearline may be blocked

Oct 10, 2013 | Dodge Cars & Trucks

1 Answer

Proportioning valves in down position


Did you open brake system lines? If you did they need power bled. If not sometime proportions do go bad.

Jul 13, 2013 | 1999 Pontiac Sunfire

1 Answer

Proportioning Valve 87 Chevy Celebrity


Usually if the car has a valve it is mounted on the firewall. But your master cylinder has 4 connections, one for each wheel. So I doubt your car has a separate proportioning valve. You could check with the dealer to verify.

Jul 12, 2013 | 1987 Chevrolet Celebrity

1 Answer

My brakes are not working correctly, the front left and rear right are not working at all. Whats wrong with it??


Your proportioning valve is likely stuck to one side. Was there a break in the line recently? That is usually the cause of this condition. To reset the valve, try opening the right front bleeder and collapsing the left front caliper piston back into the caliper. This will put back pressure on the valve. Then try normal bleeding process. If this doesn't work, you may need to replace the proportioning valve. The book says your valve is below the master cylinder. If you need more instructions or have questions, please get back to me.

Dec 01, 2010 | 2003 Mitsubishi Eclipse Spyder

1 Answer

Where is the proportioning valve on a 2000 chev blazer and can it be reset


Proportioning valve for the brakes? rear brakes? rear brakes are located on the rear end, for all brakes(front to rear proportion) is usually part of or under the master cylinder, and if either are bad then you need a new one, there is no resetting them

Feb 23, 2010 | Chevrolet Nova Cars & Trucks

1 Answer

The ABS/proportioning valve is not working.


these trucks need a seperate bleed procedure for ABS you need a scanner to put it into this bleed mode,hope this helps if not get back to me and we'll go from there. please rate my fix as i strive to be the best

May 19, 2009 | 1997 Chevrolet Blazer

1 Answer

No brake fluid flow to right rear brake


the stratus is know for clasped rear brake hoses .This stops the flow off brake fluid. try opening the brake lines at the master cylinder that go to the rear.pump up brakes first! if you got fluid than check the brake line if this is rear disc brakes on the line at the rear will be a built in proportioning valve.if drum loosen rubber hose line before the rubber part to see if you have fluid. If you do replace the brake hose! On you 74 challenger by the way i love dodge! any way on the valve there is a small button on the front of the proportioning valve that pops out it needs to be tap in lightly. also hit the brake peddel kind of hard a couple off times if that doesn't work. thanks for your question


p.s that hex bar on the is a junction not a proportioning valve .

Apr 29, 2009 | 2001 Dodge Stratus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

616 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...