Question about 2003 Nissan Altima

1 Answer

I need to see the headlight assembly

I have one dem light , i put a new one in but i think it is not getting a ground

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 3 Answers

There is a recall on this problem, it is because of a metal backing plate for the light bulb. check your dealer.

Posted on Oct 22, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 GMC Acadia. No power to headlight switch assembly. No light, won't do anything. Daylight running light do work and turn lights on. Relay? Which one?


Not sure I follow you.
Since 2000 most GM models use the dimmer switch and headlight switch to ground the lights instead of providing power.
The headlights get power from fuses for left and right, control is on the ground circuit side. So the ground wires go thru the dimmer then the headlight switch to complete the circuit.
The body control module grounds the headlight relay.

Oct 04, 2015 | GMC Cars & Trucks

1 Answer

Brake lights work til u turn headlights on then no brake lights and taillights go out dash lights. Dem


I feel the two problems are unrelated because there on separate fuses check your dimmer switch for the dash. for the rear brake lights check the fuse. if the fuse is good you have a bad ground. if the fuse blows after installing a new one its a ground wire

Feb 19, 2015 | Cars & Trucks

3 Answers

I put a new grill on my 1998 gmc Sierra and when I put the headlights back on and tested them out all the power is directed to the passenger side lights and the other side is dim!! Also when I turn my left...


The first thing i would check is the ground, check the driverside lights ground wire, this wire is bolted on the same side you will need to look around that area for that ground or run a new ground wire to the lights and see if that does it, as far as the wipers turnning on this may be due to the ground problem, i would first locate the light problem and go from there, check the connection for both the lights.

Apr 14, 2011 | 1998 GMC Sierra

1 Answer

How to change the headlights?


Hi there, here are some few tips to assist you:
  • Remove the center cover and the screws attached to the radiator grille. Pull the radiator grille out of the engine compartment and set it on the ground.
  • Use a T30 Torx screwdriver to remove the two primary retaining screws from the headlight assembly. Make a note of each screw's original location--they're not interchangeable, so you'll need to put them back in the right slot to reassemble the light.
  • Draw the headlamp assembly away from the car and then disconnect the electrical wiring connector.
  • Release the wire clip on the back of the headlight assembly and remove the cover.
  • Disconnect headlight electrical connector and turn the bulb socket counterclockwise to remove it from the assembly. Install the new bulb, replace the cover and reattach the electrical connector.
  • Reconnect the headlight assembly wiring connector. Test the new bulb to make sure it works before replacing the retaining screws and radiator grille.
Hope these help. Please rate me if they do.

Jan 08, 2011 | 1999 Mercury Cougar

1 Answer

How to replace Head light & running light switch


remove the 4 bolts that hold the headlight assembly into the chassis frame.
For example, to remove the left front headlight;
It takes a 9006 low beam bulb, OEM is 51 watts If you buy a halogen upgrade, it will be a 55 watt bulb I don't know if you can put a super xenon bulb in there, it may harm the harness, I don't know so don't rely on me for that...
Lift the hood Get a socket head wrench and some SAE (standard) sockets. Find the socket that fits the bolt head just above the headlight. I think it is a 3/8's or slightly larger.
There are 4 bolts screwed through the frame into the top of the headlamp assembly. The bolts on each end of the headlight are longer and go all the way through the assembly to align it properly.
Lay each bolt out, on the ground in the order you removed them. The middle two bolts are short, maybe 1 " and the ends are closer to 3.5" long.
Once the bolts are out, slide the headlight assembly forward. There are two bulbs, a high and low beam. The low beam bulb is to the outside of the car, or drivers side on the left, farthest to the passenger side on the right.
Most of the time the low beam will burn out since it's used 90% of the time.
The bulb has a right angle fitting with a wiring harness attached. With your hand or a channel lock pair of pliers, gradually rotate the light bulb base counter clockwise until the unit is loose in the socket holder.
Disconnect the bulb from the wiring harness and replace it with the new bulb.
Reverse the process and turn on the headlights to check you have the bulb harness properly attached before finishing up the reassembly of the 4 bolts.
Your bulb alignment with the ground should not have changed from this work. Have fun...not difficult. Takes about 10 minutes per bulb.


Read more: http://wiki.answers.com/Q/How_do_you_change_the_headlights_of_a_94_Chrysler_LeBaron#ixzz19JuBNGBU

Dec 27, 2010 | 1992 Chrysler Lebaron

1 Answer

Low Beam Drivers Side doesn't work ... low voltage,


Power for the headlights on the Left side (High and low beam.) comes from the same fuse... The ORANGE wire and the ORANGE/BLACK are the same, they connect in the harness. If you only lack the 12v to make the light work connect them at the headlight assembly.

If your low beam also lacks ground the Left low beam ground is shared with the right low beam ground... Run a wire from left low beam DARK BLUE to right low beam DARK BLUE/WHITE.

If its not working now then your cursed, seek a witch doctor.

May 23, 2010 | 2004 Buick Regal

Not finding what you are looking for?
2003 Nissan Altima Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...