Question about Mitsubishi Diamante

1 Answer

NO POWER IN VEHICLE - Diamante Mitsubishi Cars & Trucks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

2006 H3 had battery checked twice yesterday and had 781 CCA. This morning the vehicle has no power at all and the key is stuck in the ignition. What could this be?

Posted on Jun 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why won't my 2000 Ford Expedition turn on. Is the battery dead when lights won't come on or it won't light up inside. Dash won't light up. Nothing comes on.


IF you have no power then 99.99999% the battery will be dead. So it will either need to be charged if it will still hold a charge or it will need to be replaced. There may also be other issues(see 2) but that is where to begin.

You might also try and start the vehicle using jumper leads connected to another vehicle. After the leads are connected properly , start the engine in the other vehicle and then try to start your engine. You do not always need to start the other car but you will if the battery fitted to the other vehicle has insufficient cranking amps to turn over the starter motor in your car. If your vehicle starts and you have normal power to lights and accessories once your engine is running (and you are disconnected from the other vehicle) then you know your battery is possibly the only issue.

How to Jump Start Car


2. However, your alternator must also be providing power to the vehicle when it is running and the alternator also charges the battery whilst your engine is running.. If the alternator is faulty and not generating the power supply, your battery will be the only power source and it will run down very rapidly. In your case(with a 2000 model vehicle) I would definitely have the alternator checked to ensure it is generating the required power because eventually these components do fail and need to be replaced.



================================================

Jan 30, 2016 | Ford Cars & Trucks

1 Answer

2004 ford expedition eddie bauer All the doors won't lock/unlock, just make a buzzing sound repeatedly. Also does this when shutting the vehicle off.


What makes a buzzing sound , the door lock actuators ? Or where do you hear the buzzing coming from if not at the doors ?
Power Lock
The power lock/unlock feature requests all of the vehicle doors, including the liftgate, be locked or unlocked upon a customer request from any interior door lock switch in the vehicle. The power door locking system functions independently of ignition status or vehicle speed. When the vehicle security module receives an unlock/lock command from any door lock control switch, the vehicle security module will activate relays internal to the module to supply the correct power and grounds for the door lock actuators.
Visual Inspection Chart Mechanical Electrical
  • Binding latches
  • Central junction box (CJB) fuse(s):
    • 5 (7.5A)
    • 30 (30A)
  • Circuitry
  • Relays
  • Remote transmitter
  • Keyless entry keypad
  • Vehicle security module

  1. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
  1. If the diagnostic tool does not power up, refer to the diagnostic tool manual.
    1. Carry out the diagnostic tool data link test. If the diagnostic tool responds with:
      • SCP, UBP or ISO; all elctrconic control unitw, no response/not equipped, refer to Section 418-00 .
      • No response, not equipped for vehicle security module, refer to Section 419-10 .
      • System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs, and carry out the self-test diagnostics for the vehicle security module.
    1. If the DTCs retrieved are related to the concern, go to the Vehicle Security Module Diagnostic Trouble Code (DTC) Index to continue diagnostics.
    1. If DTCs are retrieved that are not found in the following Vehicle Security Module Diagnostic Trouble Code (DTC) Index, refer to the Master Vehicle Security Module Diagnostic Trouble Code (DTC) Index in Section 419-10 .
    1. If no DTCs related to the concern are retrieved, proceed to the Symptom Chart to continue diagnostics.

Jan 13, 2016 | Ford Cars & Trucks

1 Answer

Power steering problem is hard and dont find the power steering pomp


These vehicles have electric power steering. There is an electric motor under the steering column that provides the power steering assist. GM also had a special policy coverage on this motor as it has been notorious for causing the problems you are describing. Read on:

Some customers of 2004-2007 model year Saturn ION vehicles, equipped with electric power steering, may experience a sudden loss of power steering assist, which could occur at any time while driving the vehicle. If the power steering assist is lost, a chime will be heard and the Message Center will display a "PWR STR" warning message. The vehicle can still be steered in a safe manner but will require greater driver effort at low vehicle speeds or when stopped. Typically, the next time the vehicle is started, the power steering assist will return and the "PWR STR" message would no longer be displayed..................
This special coverage covers the condition described above for a period of 10 years or 100,000 miles (160,000 km), whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership.
Retailers are to replace the power steering motor. The repairs will be made at no charge to the customer.

Aug 05, 2011 | 2004 Saturn ION

1 Answer

How do I get my power steering pump out of 2002 yukon


Hello walker_227,

Removal Procedure:

SPECIAL TOOLS: You will need a power steering pulley remover and installer tool, DO NOT USE A HAMMER.

1. Remove the power steering pulley.
2. Raise the vehicle.
3. Remove the oil pan skid plate from the vehicle, if equipped.
4. Place a drain pan under the vehicle.
5. Remove the power steering pressure hose from the power steering pump from underneath the vehicle.
6. Lower the vehicle.
7. Remove the return hose from the power steering gearbox and the power steering pump.
8. Remove the bolt retaining the rear bracket to the engine.(See picture below)
9. Remove the bolts from the front of the pump.(See picture below)
10. Remove the pump from the vehicle.
11. Remove the bracket from the rear of the pump

Installation Procedure:

1. Reverse above procedure
2.Fill and bleed the power steering system.

netvan_20.png

Mar 14, 2011 | 2004 GMC Yukon

1 Answer

Warning stating reduce engine power and something about stability


Reduced power mode is when the electronic ignition is strategically is not firing all the cylinders to prevent catastrophic failure of your engine. The reason for the GM Engineers put the reduced power mode in the vehicle is so you can drive the vehicle under 50Mph for about 50 miles to a mechanic before the vehicle completely dies.

Jul 01, 2010 | 2003 GMC Yukon Denali

1 Answer

My key will not start vehicle. I have full power


Is the fuel pump coming on? If not that is what it is. A bad fuel pump.

Nov 10, 2009 | 2003 Chevrolet TrailBlazer

1 Answer

Need to replace high pressure power steering hose on 2004 Monte Carlo SS. Need tips to effectively do the job myself. Tools needed, tricks to make the job easier, what not to do...etc. Thank yiou so much...


Power Steering Line/Hose: Service and Repair
Pressure Hose
Power Steering Pressure Pipe/Hose Replacement (3.8L)
Removal Procedure
1. Place a drain pan under the vehicle.
2. Remove the accessory drive belt.
3. Raise and support the vehicle. Refer to Vehicle Lifting.
4. Remove the tire and wheel assembly.
5. The power steering pressure hose is the lower hose at the power steering gear.
Remove the power steering pressure hose from the power steering gear.
6. Remove the power steering pressure hose from the power steering pump.
7. Remove the power steering pressure hose from the clamps on the power steering gear.
8. Remove the power steering pressure hose from the vehicle.
Installation Procedure
1. Install the power steering pressure hose to the vehicle.
2. Install the power steering pressure hose to the clamps on the power steering gear.
Notice: Refer to Fastener Notice in Service Precautions.
3. Install the power steering pressure hose to the power steering pump.
^ Tighten the fitting to 27 Nm (20 ft. lbs.).
4. Install the power steering pressure hose to the power steering gear.
^ Tighten the pressure hose fitting to 27 Nm (20 ft. lbs.).
5. Install the tire and wheel assembly.
6. Remove the drain pan from under the vehicle.
7. Lower the vehicle.
8. Install the accessory drive belt.
9. Fill the power steering system with power steering fluid.
10. Bleed the power steering system.
11. Inspect the power steering system for leaks.

00d203e.jpg

Sep 15, 2009 | 2004 Chevrolet Monte Carlo

1 Answer

Power steering hose, leaking. How to replace power steering hose.


You will have a leak from the pump, pressure hoses or the rack. You will have to get the system washed down and inspected for the leak, most common problem is the steering rack leaking, this will leak oil onto the exhaust and cause your smoking problem, start her.


Remove the power steering pump pulley.
Place a drain pan under the vehicle. Important: Cap or plug the ends of the power steering hoses to prevent fluid loss.
Disconnect the power brake booster inlet hose from the power brake booster.

248015_2_34.gif

Disconnect the power steering cooler hose from the power steering pump.

248015_3_27.gif

Disconnect the power steering pump remote reservoir hose from the power steering pump.

248015_4_19.gif

Raise and support the vehicle. Refer to Vehicle Lifting.
Remove the power steering pump rear mounting bracket nut.
Lower the vehicle.
Loosen the accessory bracket bolts and nut. Pull the accessory bracket forward.
Remove the power steering pump mounting bolts.
Remove the power steering pump and the power brake booster inlet hose from the vehicle.
Remove the power brake booster inlet hose from the power steering pump.







Jul 23, 2009 | 1994 Toyota Corolla

3 Answers

Battery went flat cannot unlock vehicle


U can get in by using a tool called a "slim jim"

Apr 26, 2009 | Land Rover Discovery Cars & Trucks

2 Answers

My power steering pressure hose has a leak.


i pERSONALY WOULD REPLACE IT MYSELF EVEN WITHOUT MY 30yrs Of Experience in this Field. I have Enclosed Instructions for you to use. PLEASE dont Forget to RATE me As MOST folks DONT remember to that is how WE Get our Ratings such as GURU THANK YOU and Good Luck On The Job, Dont PAY a dime If YOU CAN > D I Y

REMOVAL PROCEDURE
  1. Remove the power steering pressure hose (2) from the power steering pump (1).
  2. Raise the vehicle on a hoist. Refer to Vehicle Lifting.
  3. Remove the front exhaust pipe, automatic transmission only. Refer to Intermediate Pipe Replacement in Exhaust System
  4. Remove the power steering pressure hose (1) from the power steering gear (3).
  5. Remove the power steering hose retainer (2).
  6. Remove the power steering pressure hose (1) from the vehicle
    1. Install the power steering pressure hose (1) to the vehicle
    2. Install the power steering hose retainers (2). NOTICE: Refer to Fastener Notice in Service Precautions.
    3. Install the power steering pressure hose (1) to the power steering gear (3). Tighten the fitting to 27 Nm (20 ft. lbs.).
    4. Install the front exhaust pipe, if removed. Refer to Intermediate Pipe Replacement in Exhaust System.
    5. Lower the vehicle.
      1. Install the power steering pressure hose (2) to the power steering pump (1). Tighten the fitting to 27 Nm (20 ft. lbs.).
      2. Bleed the power steering system. Refer to Bleeding Power Steering System in Service and Repair of Steering.

Mar 27, 2009 | 1999 Pontiac Sunfire

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

292 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...