Question about 1989 Dodge Colt Vista

2 Answers

No fire 1989 dodge not firing replaced coil

Posted by on

  • williamgordo Sep 21, 2008

    where is it located


2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I need help no fire coming from coil to dis or plugs what do i do

Posted on Mar 14, 2016

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 2,920 Answers

Check the crankshaft sensir they go bad and keep it from firing

Posted on Sep 21, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Firing order for a 1989 Dodge Danasty 3.0

My info says the firing order is 123456.

Dec 14, 2014 | 1989 Dodge Dynasty

2 Answers

1989 Ford F 150 has fire but won't start replaced fuel pump pick up and moduale. what else could it be?

You need to run a fault code test on the computer control module. To learn how go here. The code lists are there as well.

Nov 06, 2012 | 1989 Ford F 150

1 Answer

1989 dodge raider that will not run. Ran for a few days then quit and changed the ingitor,and distributor still don't have any fireing t the coil. Can't fine the self diagnosis connector to check the

Make sure timing belt is still intact I had a friend with a Dodge omni he couldn't figure why he had no spark and turns out the timing belt was broke that said also look at your module normally no spark is due to a fryed module

Dec 05, 2011 | 1987 Dodge Raider

2 Answers

I have a 1989 RAM w100 with a stock 318. I'm

If you can spray carb cleaner in the carb then you have either a fuel supply problem or fuel delivery problem. Check your fuel pressure and make sure it is in spec. Then check the spray in the carb spray.

May 27, 2011 | 1989 Dodge W150

1 Answer

I have a 1989 dodge dakota truck with a 3.9L. there is no fire going to the coil. i have replaced the module and the coil. still won't start. I get code 34 please help me to diagnose this problem. thanks

Replace the Automatic Shutdown Relay. If that doesn't fix the problem, the other place I would look, would be the Hall Effect Switch inside the distributor. You should be able to change this part without removing the distributor. If the computer doesn't get a signal from the Hall Effect, it will shut down the ASD, which supplies power to the coil and the fuel pump.

Feb 19, 2011 | 1988 Dodge Dakota

1 Answer

Firing problem: has fire to coil but no fire from the coil to the distributor. has new coil and cap and rotor bug. what could this be?

Try replacing your ignition control module it sounds like it has burned out. Easy to swap out. It's right under your rotor button

Jan 22, 2011 | 1989 Lincoln Mark VII

1 Answer

Engine turns over but will not start. have fuel to carb. have spark to the plugs. timing belt and timing are good. ignition fusable is ok. Engine just quit while driving. engine is 2.0L in 1989 dodge ram...

I just R&R A Motor 3,0 In a caravan and now I dont have any fire. What did I do wrong. I chaged The coil And Destrb And dont Have any. My email add. Thanks

Mar 29, 2010 | 1989 Dodge Ram 50

1 Answer

Sparkplugs not getting "fire" have already changed the coil

u have put new coil and no spark in plug , it is ur distributor cap is needed replacement but first have a look inside the distrubutor cap for any wear if is u need new one ok

Nov 05, 2009 | 1989 Dodge Dakota 2WD

1 Answer

I have a 1998 Dodge Neon. One of the coils is not firing of the two, Don't know whether it's the crankshaft or computer. What's a good way to test for either?

replace the non firing coil, very common. also replace the spark plugs and wires. I dont have a wiring diagram here at home to verify which wires are which, but if one coil is firing, they both have power.

Sep 26, 2009 | 1998 Dodge Neon

1 Answer

Need to know firing order for 1989 dodge dynisty

It should be listed in your owner's manual. Sometimes it is also listed on the ignition coil diagram. If you don't have an owner's manual, you should be able to find one in .pdf format that you can search for through Google.

Aug 02, 2009 | 1989 Dodge Dynasty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

74418 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7254 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides