Question about 1990 Cadillac SeVille

1 Answer

1990 cadillac seville brake arm

I need help with repairing the frame where the brake arm mounts through the frame. The mount hole is rusted and to large.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 123 Answers

You would have to take a picture and send to to verify fix. Sadly if its that bad I imagine the rest of the car is pretty rough underneath. Technically speaking if the car is worth fixing the welder would have to be an up to date D.O.T cerfitied welder.

Posted on Sep 21, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Is there a recall on frame on my 2004 chevy colorado frame is rusting out has holes in frame

rust is from the salt used on winter roads and there is no recall for that problem
as the repair will cost more than the car is worth , consider updating to a rust free model

May 25, 2017 | Cars & Trucks

1 Answer

How to replace front motor mount on 2000 cadillac seville

lift the car remove bolt on the h frame disconect mount

Sep 07, 2014 | Cars & Trucks

1 Answer

Rod attached to frame in front of rear wheels rusted thru can it be replaced or repaired auto great shape but rusted there

If this is an alignment rod Bar that you are talking off that goes back to the lower arm and the rust is in that attachment point where it is mounted to the frame Then it can be repaired with a new section being welded it but you will need an accredited welder / panel beater to do the job . If it is rusted through the frame then have the whole frame checked because rust is not always visible until the paint is disturbed. This part is vital to the steering stability and if not done properly will result in serious injury to the driver and others.

Aug 03, 2014 | 2000 Suzuki Grand Vitara

1 Answer

How to replace a broken tensioner on a 94 cadillac seville sls

The tensionmer is bolted on in one place and is indexed to a hole in the back of the mounting position. see picture below.

Oct 17, 2012 | 1994 Cadillac Seville

1 Answer

There is a squeaking sound on the front right wheel of my L300 van and its getting hot even on a short drive!

On older vehicles rust can be a major factor in how your brakes work. You probably have a problem with the calipers not floating properly because the brake pads are jammed in place by rust. You will probably need to purchase new brake pads, discs and possibly new brake sliders . Take the calipers off , knock out the brake pads, and carefully take of the shiny brake sliders. The rust is under the sliders. Two bolts hold the caliper mount on , it will be easier to work on if you remove it from the vehicle. Take a file and clean the rust off the iron caliper mount till there is only metal. Coat the filed surfaces on the caliper mount with anti seize and put the sliders and the pads back on. Make sure the new pads float properly (not jammed like before) and reassemble. I have had several old Mitsubishi's with rust on the caliper mount that did the same thing. Wear a mask, it is a dirty job but filing off the rust should fix the problem.

Aug 26, 2010 | 1990 Mitsubishi Minivan

1 Answer

Location of starter motor on 1998 seville

1998 Cadillac Seville STS 4.6L SFI DOHC HO 8cyl

Fig. 4.6L engine starter mounting is under the intake manifold (click for zoom)


Fig. This is where (and how) the starter motor is mounted in the engine valley on the 4.6L engine. The arrows show the 2 mounting bolts

Hope helps (remember comment and rated this).

Aug 05, 2010 | 2001 Cadillac Sts

1 Answer

Need to replace starter

You must unbolt the front engine mount,then raise the engine with a small jack.

Dec 04, 2009 | 1990 Cadillac SeVille

1 Answer

How do I R&R front motor mounts on 2000 cadillac sts

Very easy, just remove front tires and unbolt, BUT I doubt you are asking right question. Not mounts, but mount in dead front center is problem. There are 4 mounts, transmission center back, left center and right center and front center. That takes full torque of motor and heat from exhaust. GM has a shield for exhaust.

Dec 02, 2009 | 2000 Cadillac Seville

2 Answers

Where is the fuel filter located on a 1992 cadillac seville? my car wants to start, but no gas is getting to the air breather? make sense.

Unless this problem has been slowly creeping up on you, I'm going to say you need to look at the fuel pump too.

Under vehicle, driver side, below seating area, near fuel tank, mounted on frame rail in fuel line
Go to:

Get an account and use the repair manuals that they provide, will help you find things and give you good troubleshooting guides.

Sep 06, 2009 | 1992 Cadillac Seville

Not finding what you are looking for?
1990 Cadillac SeVille Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts


Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides