Question about 1990 Toyota Camry

Open Question

How to replace trunk hinges on a Camry 1990

The hinges are attach to the upper rear part of the trunk with a pivot and with two screws to the lid, how do you take off that pivoting part. Is that pivot a kind of screw?. It is only accesible through the inside of the car. Any help would be apprecited. G.

Posted by on

6 Suggested Answers

  • 4 Answers

SOURCE: 2000 Camry LE bad odor from a/c heater cabin vents

Possible the smell is coming from the bacteria living on your ac evapourator. You can buy a spray for this that you set off inside the vehicle. Follow the instructions on the tin.

Posted on Aug 10, 2008

  • 1861 Answers

SOURCE: rear license plate light 2003 Camry

The bulb number that you need is #194.
Pull off the interior trim, and you will see the sockets for the bulbs.
Thanks for selecting FixYa to answer your question.

Posted on Dec 08, 2008

  • 1861 Answers

SOURCE: 2001 Toyota Camry trunk stoplights won't work

GREAT!

I am glad the I was able to assist you with your problem.


Could you please rate my assistance level as a FixYa?
I'd really appreciate it. Thanks in advance.

Posted on Jan 26, 2009

Charlie1221
  • 61 Answers

SOURCE: trying to change both serpentine

Their should be a diagram in the front of the engine compartment. Their will definitely be a diagram in the owners manual.

Posted on Jan 29, 2009

  • 1 Answer

SOURCE: 1999 camry trunk lid & high mount brake lights all inop...

Hi,

The jiggle method is not enough you have to look at the wires. I just did and I found out that all six wires were broken close to the splice. That splice is located close to the back seat.

Hope it hepls.

Posted on Apr 23, 2009

  • 3600 Answers

SOURCE: toyota camry trunk is leaking

you have to loosen the hood hinge where the lock is and move the lock ring lower to get the lid close tighter, if the car was damaged by an accident then you will have to get it repaired by a body shop or by someone who can find the high spot that it is hitting.

Posted on Jun 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Camry code 1780


This is a problem in the Park/Neutral position switch or wiring.

Apparently Camrys of your vintage often suffer chafing and breakage of the wiring around the rear trunk lid hinge, driver's side. The backup light conductor there chafes and breaks, which the ECU sees as a fault P1780.

http://wiki.answers.com/Q/What_do_they_have_in_common_Toyota_Camry_2000_CE_trunk_lid_brake_lights_check_engine_light_P1780

Aug 18, 2012 | 2000 Toyota Camry

1 Answer

Water collects in the spare tire well of my 1990 toyota camry


Its not designed to drain.
You are probably getting water into the trunk from the trunk lid gasket or one of the tail lights.

Aug 04, 2012 | 1990 Toyota Camry

1 Answer

How do you replace shocks on 1991 buick skylark


REMOVAL & INSTALLATION Fig. 1: After you open the trunk lid, use a suitable prytool to remove the trim cover 86888036.jpg
Fig. 2: Some vehicles have a cover which must be removed to access the shock retaining nuts 86888037.jpg
Fig. 3: Unfasten the upper shock attaching nuts 86888038.jpg
  1. Disconnect the negative battery cable.
  2. Open the trunk lid and remove the trim cover. If equipped, remove the nut cover.
  3. Remove the upper shock attaching nut(s). If removing both shocks, remove one at a time.
  4. Raise and safely support the vehicle.
  5. Unfasten the lower shock absorber mounting bolts. One wrench will have to be placed on the bolt head side to retain the bolt as you loosen the nut. Usually a 15mm wrench is used to remove them. To install: Fig. 4: After the vehicle is raised and safely supported, use a socket to unfasten the lower retaining bolt 86888039.jpg
    Fig. 5: Remove the retaining bolt, then . . . 86888040.jpg
    Fig. 6: . . . remove the shock absorber assembly from the vehicle 86888041.jpg
  6. Connect the shock absorbers at the lower attachment and install the attaching bolt.
  7. Lower the vehicle enough to guide the shock absorber upper stud through the body opening, then fasten the upper shock absorber attaching nut loosely. Tighten the lower shock absorber mounting bolt to 35 ft. lbs. (47 Nm).
  8. Remove the axle support, then carefully lower the vehicle. Tighten the shock absorber upper nut to 21 ft. lbs. (29 Nm).
  9. If equipped, install the retaining nut cover, then install the rear trim cover. Close the trunk lid.
  10. Connect the negative battery cable.
prev.gif next.gif

Oct 08, 2010 | Buick Skylark Cars & Trucks

1 Answer

Car in park applied brake reverse light come on


check wire harness and light bulbs in the trunk,
also harness to the trunk lid were it attached to hinge.

Apr 22, 2010 | 1994 Toyota Camry

2 Answers

The rear lights on the trunk lid won't work. bulbs are good.


the wire harness for the bulb can be bad..thats what was wrond with my concord...lol but its a crysler...haha

Mar 10, 2010 | 1999 Toyota Camry

1 Answer

Icon of the trunk of my camry is always lit up on my dash board


check the rear bulbs on the car and if thier good check the wirring going to the trunk lid for shorts or opens

Jul 15, 2009 | 1990 Toyota Camry

2 Answers

My Boxter battery is dead and I am not able open the trunk lid.


I have had this occur before. After I called AAA they showed me what I was doing wrong. The diagram in the book dose not show the correct place to ground the cable. It shows that you should attach to a door latch near the rear of the car. Acutally, you need to ground the cable by attaching to the door hinge. Hope that helps.
Sandra

Apr 06, 2009 | 2002 Porsche Boxster

1 Answer

1999 camry trunk lid & high mount brake lights all inop...


Hi,

The jiggle method is not enough you have to look at the wires. I just did and I found out that all six wires were broken close to the splice. That splice is located close to the back seat.

Hope it hepls.

Mar 19, 2009 | 1999 Toyota Camry

1 Answer

Trunk lid hinge replacment


lift trunk lid and support it
unbolt hinges
remove trunk lid
bolt in new hinges

Dec 31, 2008 | 1988 Toyota Celica Liftback

1 Answer

1988 camry rear lights.


Look at the wiring harness that runs along the hinge on the trunk lid, driver side. Camrys with lights on the trunk lid are know to break one of these wires.

Sep 26, 2008 | 1988 Toyota Camry

Not finding what you are looking for?
1990 Toyota Camry Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...