Question about Hyundai Accent

1 Answer

Need arms like ape to turn steering wheel - Accent Hyundai Cars & Trucks

Posted by on

  • dennisfitzs Sep 22, 2008

    thanks for comment,does not have power steering

  • Coss May 11, 2010

    Have you checked the fluid level in the steering pump?

    How long has this problem been happening?

    Did it happen all at once? Or did it gradually get worse?

×

1 Answer

First i would check the power steering pump do u have fluid if not check for leaks if not the check tie rods may be bad or out of alignment

Posted on Sep 20, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn signal stays on


On a steering wheel are 2 pins. These pins turn the signals off as the wheel returns from making a left or right hand turn. They reset the blinker mechanism by bumping the blinker arm and pushing the arm back to the center position. You can sometimes see these little pins that reset the blinker if you look between the steering wheel and the steering wheel column. There is a little gap where the steering wheel is enabled to turn with out rubbing the column. You will also see a circular copper plate in there where the horn makes electrical contact by a little flat tension arm and rubs the copper surface as the wheel spins in either direction.
To repair a damage blinker pin, the steering wheel most likely has to be pulled off and the pin repaired and steering wheel returned back onto the column. Not a big job at all, just more of a pain then anything. Some steering wheels are on pretty tight on their splines and a puller may be needed. If the pins are still intact in the back of the steering wheel, then the blinker mechanism has a problem and is not be triggered to return to center by the pins.

Aug 11, 2014 | Mitsubishi Montero Sport Cars & Trucks

1 Answer

Power steering doesnt turn, is it my power steering switch???


Hi Chris, the concept of power steering in cars and trucks should read POWER ASSISTED, this means if your power steering fails, you can still steer the vehicle unlike some machinery and tractors that have full power steering which the steering wheel will just spin when the engine is turned off with no connection to your wheels, If your steering wheel does not turn it is a mechanical problem, steering arm jammed pitman arm in the wrong position or something like that. remove the pitman arm off the steering box and see if it will turn. you did mean that it won't turn at all and not turn easily like power steering should

Jan 04, 2014 | 2001 Chevrolet Tahoe

1 Answer

Nissan Elgrand E51 free play on steering wheel


depends. could be your idler arm or pittman arm assembly. sometimes bushings wear out and cause play in the suspension and steering. look under your vehicle while someone else turns the wheel and see if you notice a 'lag' when the wheels turn anywhere. if not jack up the entire front end and turn the wheel with your arms while looking at the linkages. i'm sure you will spot the problem.

Nov 06, 2013 | Cars & Trucks

1 Answer

1998 F 150 stuck steering knuckle


Are you sure it is the knuckle joint and not the steering arm pump? I would disconnect the steering from the steering arm mechanism and pump and see if the steering wheel turns freely. If it does you have another problem. Typically if you were hearing a "whining" noise when turning the steering wheel before this problem occurred your problem is going to be the pump or the mechanism to the pump connects to that controls the steering arm.

Oct 17, 2011 | 1998 Ford F150 Regular Cab

1 Answer

Pitman arm or steering box clunks when steering back and forth.Steering box shaft on pitman arm seems like play in it.


There is an adjustment on the steering box.You will see a stud with a nut on top. Loosen the nut,and turn the stud with a screwdriver while moving the steering wheel back and forth. Don't tighten too tight,as the steering wheel won't return to center when turning a corner. If that doesn't stop the clunk,you will need to change out the steering box.

Jul 19, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

What does a ideler arm for a 2003 Kia Rio do problem:


The kia rio uses rack and pinion steering, which does not use an idler arm. Did someone tell you you had an idler arm?

For cars that have classical steering designs, the idler arm is a part of the steering linkage that makes the front wheels turn about the same on both sides. Actually, the wheel on the side of the turn turns a little bit more. The idler arm is necessary for the wheels to turn properly. When the joints in the idler arm wear out, the right wheel is allowed to move back and forth on it's own. This causes vinration, excess tire wear, and possibly an unsafe steering condition if the wear is excessive. .

Dec 12, 2010 | Kia Rio Cars & Trucks

1 Answer

Chevy g20 van steering driver replacement problem


Cannister is your steering box...arm is the pitman arm. check to see if there is a thick alignment spline on either the arm or box. This locates the arm in the correct position. If not center the steering wheel(turn all the way to one side and count turns all the way to other side and divide in half for example, three turns from one side to the other side = 1 1/2 turns to center) and put both front wheels straight ahead, then install arm onto box. It is far easier to put it back than it was to remove.

Jun 20, 2009 | 1989 Chevrolet G20

1 Answer

2003 Ford F350, massive hydrolic pwr steerinfluid leak


What I think you are referring to as the pump is really the steering box because the pump doesn't have an arm connected to it. The pump has 2 hoses and a belt going to it. From what you describe it sounds like you need a pitman shaft seal. The seal is replaceable but you will need a pitman arm puller to get the pitman arm off. If you don't have or can't get a puller don't even bother starting the repair, as you WILL NOT get the pitman arm off without one. When you get the pitman arm off clean out around the shaft and you will see a snap ring. Remove the snap ring. Now make sure the power steering is full of fluid. Start the engine and turn the steering wheel all the way one way or the other and hold it there while increasing the RPM. Doing this will literally "BLOW" the seal out. There will be a couple of spacers and maybe another seal that come out of the hole also. So read the installation instructions that come with the seal kit and it will have a picture of where the components go and in what order they go in. Don't forget the snap ring. When done replaceing the seal you have to center the steering box. From all the way one way turn the steering wheel all the way the other way and count the turns. Now turn back the other way half as many turns and the box is centered. With the tires pointed straight (not turning) the pitman arm should go right on. The pitman arm will go on the pitman shaft in 4 different places. So if you don't center the box and the wheels you might have say one turn to the right before the steering wheel stops and three turns to the left. With all this done fill the power steering with fluid. With the front tires off the ground and the engine NOT running turn the steering wheel all the way from stop to stop 4 or 5 times and then check the fluid again. Fill the fluid and turn wheel from stop to stop another 4 or 5 times. Doing this will "bleed" most of the air out of the system. Now start the engine and turn wheel from stop to stop a few more times to "bleed" any remaining air from system. Turn off the engine and check fluid level. Hope this is helpful.

May 11, 2009 | 2001 Ford F350 Super Duty SuperCab

2 Answers

2000 Jeep cherokee steering wheel alignment


to remouve the steering weel and drive the vehicle slowly look on fordwar in line and replace the colum ,, the noise must came from the adaption that you made . raise the vehicle and see were is any part for the suspention that toutching the chassis and ajust it......

Dec 22, 2008 | 2008 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...