Question about 2001 Dodge Stratus

1 Answer

2000 dodge stratus problem

We already try to shaft crank sensor and is not that, we dont know what it could it be causing this problem, i am guessing it might be something electrical because it runs but then it turns off, like the power goes away, and then i need to wait a few minutes for the car to start.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 360 Answers

Crank sensor???? it might have a short in the 5 volt power supply. crank sensors can confuse the computor to thinking its the cam sensor. good luck

Posted on Sep 20, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Camshaft Sensor 2003 Dode Stratus RT 3.0


The cam sensor is usually located at the front, on the end of a cam shaft. You may also want to change the crank position sensor. BUT.......check the timing belt first, make sure it is still intact. I'm not sure if they still used the Mitsubishi engine in 03, but check your cap too. The distributor cap also (I think...) has a pick up and a silver disc under the cap. The Mitsubishi engine, they went bad frequently.

May 10, 2014 | 2003 Dodge Stratus

1 Answer

2000 dodge stratus misfiring on cylinder 4


how do you know its missing on no4 cyl ,is it running ok by any chance

Nov 20, 2011 | 2000 Dodge Stratus

1 Answer

My 1999 2.4 dodge stratus wont run unless i unplug cam sensor its a new sensor and a new crank sensor


I'm having excatly same problem, found this sequence to ge the car running again..turn off ign, unplug cam position sensor, crank for 2 seconds, connect cam shaft sensor, crank again and it starts like that...

Apr 01, 2011 | 1999 Dodge Stratus

1 Answer

Where is the cranksensor in a 2005 dodge stratus


You can find the crank shaft sensor in your car under the starter located over the motor mount..You have to remove the starter to reach to the crank shaft sensor.

Nov 06, 2010 | 2005 Dodge Stratus

2 Answers

A 2004 Dodge stratus with the 4 cylinder that will not start


code p 16 refers to crankshaft position/cam shaft position bank 1 sensor A--correlation====causes ---wiring---CKP sensor ( crankshaft position sensor )---mechanical fault

code p 0340 refers to -camshaft (CMP) sensor A bank 1 circuit malfunction ===causes wiring--CMP sensor--ECM
cosrs nothing to check the timing belt , just remove the oil filler cap and see if the rockers are moving when turning it over
the clue here may be bewteen the 2 codes , the word correlation and circuit malfunction so check the wiring, harness connections for pin corrosion and then substitute the ECM with a know good unit as the correlarion and circuit malfunction could be in the ECM
if the ECM program is not getting good reports for both sensors then it reasons that the piston and cam shaft are not timed properly and so will not allow it to start

May 15, 2017 | 2004 Dodge Stratus

3 Answers

I have changed the timing belt on a 99 Dodge Stratus with a 2.4 liter engine. All timing marks are aligned properly according to Haynes diagram and the engine will still not start. It tries to start


check your distributor position,double
check all marks again,make sure when u line up
the crank marks at #1 cyl. at compression and cam shaft marks!!

G

May 28, 2009 | 2001 Dodge Stratus

2 Answers

Crank shaft sensor


replacing the crankshaft sensor might solve the problem.

Aug 19, 2008 | 2001 Dodge Stratus

Not finding what you are looking for?
2001 Dodge Stratus Logo

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

71338 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7018 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...