Question about 1990 Dodge Dynasty

2 Answers

Every once in a while my car doesn't want to start. When I turn the key it clicks then the alarm reactivates and i have to disarm it. but then my battery seams to die i checked my battery and thats not the problem then i checked my alt and thats not the problem. What else could it be?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Had similar problem. Slow drain on battery was due to GLOVE BOX LAMP draining battery very very slowly. Switch would not turn lamp "OFF". Electrical repairman said this happens often. He advised to REMOVE LAMPS from inside GLOVE BOX---Under HOOD and inside TRUNK. The switches fail keeping lamps "ON" thus never being seen but slowly drain battery.

Posted on Apr 04, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 512 Answers

How did you have th battery checked...most stores like auto zone only check the voltage...it is possible for a battery to show 12 volts and have very little amps ...this could cause your problem

Posted on Oct 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you turn off an alarm for a 2005 Saturn Ion


Disarming an Armed System/Silencing an Alarm
If system arming has been requested by the keyless entry transmitter, it must be disarmed.
Important: Using the power door unlock switch or manually unlocking the doors does not disable the CTD armed mode. Also, disconnecting the battery or pulling fuses does not disable the armed mode, since the BCM stores the CTD mode status in memory.
?€¢
To disarm the CTD system in arm pending mode, SECURITY indicator flashing and doors open, perform 1 of the following:


-
Press the UNLOCK button on the keyless entry transmitter.


-
Insert a valid key into the ignition and start the vehicle.


?€¢
To disarm the CTD system in the armed mode:


-
Press the UNLOCK button on the keyless entry transmitter.


-
Insert a valid key into the ignition and start the vehicle.


?€¢
To disarm the CTD system when activated, alarming mode.


-
Press the UNLOCK button on the keyless entry transmitter.


-
Insert a valid key into the ignition and start the vehicle.

Jun 24, 2016 | 2005 Saturn ION

2 Answers

How do I reset the alarm on a 2005 hyundai Santa 2.4l


Not sure about yours, but many will reset by: turn key to "on" and wait 15 minutes or so; shut off, then try to start.

Apr 15, 2016 | Hyundai Cars & Trucks

2 Answers

Antitheft system keep goes on so i can't start my vehicle


It is telling me to lock the doors with the key, this will arm the system, then you should be able to unlock the doors after about 3 seconds and this should disarm the system. Also, if it doesn''t try unlocking the passenger side door or the back glass with the key. Let me know you must wait at least 3 seconds before unlocking back glass or passenger door to disarm system once one door is unlocked without setting off alarm it is disabled. hope this helps

Aug 06, 2014 | 1998 Nissan Pathfinder

1 Answer

2001 mitsubishi eclispse gs wont start how do you bypass the security system


  • 1 Turn the ignition key counter clockwise in the driver's side door to unlock the caricon1.png. This deactivates the alarm long enough for you to gain access to the vehicle. Then, place the key in the ignition and turn the key until it clicks once. This starts the car's battery, but doesn't ignite the engine. The LED light on the dashboard should stop blinking, indicating the alarm is temporarily disabled.
  • 2 Locateicon1.png the box for the alarm under the dashboard on the driver's side of the car. Then, look for the override button on the box. Typically, the small button is either red or black. With the ignition key in the "on" position, press the override button and hold it in until the alarm chirps once. This disables the alarm until you manually reactivate it.
  • 3 To reactivate the alarm, turn the key to the "on" position and press the override button once. The alarm chirps twice, indicating the alarm is active.

  • Hope this helps!

    Mar 15, 2014 | 2001 Mitsubishi Eclipse

    1 Answer

    Disarm alarm


    Get in the car, shut the door, and insert key in ignition.

    Turn the key to the RUN position (NOT start, but the position the key is in when the car is running. You DON'T want to start the car).
    Turn key off.
    Repeat this 10 times quickly (ON, OFF, ON, OFF, etc)

    Many alarm systems this is at least one way to reset or over-ride the alarm.

    Jan 28, 2014 | 1996 Ford Escort 4 Door

    1 Answer

    Disabling alarm system on 2000 mitsubishi mirage


    this is a long shot, put the key in the driver door, turn to unlock then try to start the car, some systems disarm when the key is used to unlock the car.

    Jul 05, 2012 | 2000 Mitsubishi Mirage

    1 Answer

    Left lights on ,and ran down battery. When i try to jump start, alarm goes off,key fob wont work till battery charges tried putting key in ignition and turning key, tried locking and unlocking door. what...


    Find the alarm and disconnect it, or locate the fuse to the alarm and remove it. Then you can charge the battery without all the noise. Once the battery is charged, hook the alarm up and disarm it with the remote.

    Dec 28, 2010 | Kia Spectra5 Cars & Trucks

    1 Answer

    Alarm button broken. Cannot disarm alarm. What do I do? Chrysler Town & Country LX 2003 model.


    You can arm or disarm alarm manually with the key at the drivers side door, turn the key to open the locks and the alarm must be disarmed.

    Nov 01, 2010 | 2003 Chrysler Town & Country

    1 Answer

    My door remote thingy is broken and i can't lock it nor can i drive it without the alarm going off. Can i disable the alarm somehow?


    NO WAY,you have to have a remote to set/unset the system.(if you could, so could any tom,****.harry.)so you know, the key has ONE code,(constant)the car has two codes,one rolling and one constant)the remote searches for the rolling code and then disarms it,so that when you put the key in it starts.....then when you lock with the remote it reactivates a different code,simple but effective deterrant for thieves.....and other mitsi owners.

    Oct 26, 2010 | Mitsubishi Mirage Cars & Trucks

    2 Answers

    HELP please!! My daughter has a 96 sebring convertible and today she put her key in the door to unlock it and the alarm started going off. It wont stop, have disconnected the positive and negative battery...


    Just a quick note once you hook the battery back up try locking it and unlocking it from the drivers door, if that fails you might try the passenger door. I know on some chrysler products you have to lock and lock again to arm and unlock to disarm. I hope this helps.
    Thanks,
    Joey

    Sep 05, 2010 | 1998 Chrysler Sebring

    Not finding what you are looking for?
    1990 Dodge Dynasty Logo

    146 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dodge Experts

    yadayada
    yadayada

    Level 3 Expert

    60667 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21936 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6811 Answers

    Are you a Dodge Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...