Question about 2002 Mazda Protege

1 Answer

Remove back seat

How do I remove the back seat. Looks like it is bolted.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 2 Answers

The back seat simply "snaps" into place. Grab the seat one one side and firmly pull up on it. The seat should pop out of its connector. Do the same to the other side. Seat should come right out.

Posted on Mar 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How to remove back seat in 1972 buick skylark


Remove the seat cushion retaining bolts, detach the seat cushion and remove it up and out from the vehicle.

Remove the rear seat back retaining bolts at the bottom of the seat back. Pull up then out to disengage the upper frame from the hangers and remove seat back from the vehicle.

Installation is the reverse of removal.

Courtesy: Haynes GM repair Manual #38025. You can probably find a copy of it on Amazon or eBay cheap

Jun 20, 2011 | Buick Skylark Cars & Trucks

1 Answer

Front Seat removal problem on a 2006 Pontiac Gran Prix. I have tried to run the seat all the way back but the front seat Bolt goes down into the floor but when you look UNDER the car there is No NUT there...


There should be some small plastic trim covers over the bolts on the very front of the rails. Remove those trim covers. The bolts will be underneath. If memory serves me you will need a torx socket to remove them. A T45 or T50 male torx socket comes to mind.

Jun 08, 2011 | Pontiac Grand Prix Cars & Trucks

3 Answers

How do i take the back off on a 1999 nissan maxima bucket seat


Hi, follow the instruction below......
Rear
See Figures 3, 4, 5 and 6
  1. Remove the lower seat cushion by pulling straight up on the front portion and disengaging the clips. Then hinge the seat upward to release the rear clips.
03b6e0a.jpg

Fig. 3: Pull up on the front of the lower seat cushion and disengage the clips
  1. Remove upper rear seat back-to-chassis bolts.
77eb191.jpg

Fig. 4: Remove the bolts behind the center armrest ...

a796228.jpg

Fig. 5: ... and the bolts on the lower corners ...

fbf100a.jpg

Fig. 6: ... Then pull up on the seat to disengage the three clips on the top of the seat
  1. Remove rear seat back by tilting forward and pulling straight up.

To install:
  1. Install the lower seat cushion and torque the lower rear seat-to-chassis bolts to 15-20 ft. lbs. (21-26 Nm).
  2. Install the upper rear seat back cushion and torque the upper rear seat back-to-chassis bolts to 15-20 ft. lbs. (21-26 Nm)

Jan 19, 2011 | 1999 Nissan Maxima

4 Answers

Where is the fuel pump


REMOVE THE REAR BACK SEAT BOTTOM TO GAIN ACCESS, THE SEAT IS HELD IN BY 2 BOLTS. YOU WILL NEED A 10MM OR 12MM SOCKET TO LOOSEN THE SEAT. BOLTS ARE LOCATED BETWEEN THE SPACE WHERE THE SEAT MEETS THE SEAT BACK. WHERE THE REAR SEAT BELTS COME OUT. WHEN BOLT ARE REMOVED PUT YOUR HAND BETWEEN THE SEAT AND PULL UP YOU WILL SEE WHERE THE FRONT HALF OF THE SEAT IS SECURED BY A 'L' SHAPE BRACKET LOCATED IN THE FRONT HALF OF THE REAR SEAT GOING INTO THE FLOOR BOARD.

Jan 13, 2011 | 1996 Acura TL Series

1 Answer

Is there a rear seat release on a 94 accord


I believe this procedure applies to your 94 Accord:
With your hands, press down on the seat cushion where it meets the seat back. Locate the retaining bolt(s). Some models retain the seat with one bolt in the center; others use two, evenly spaced left and right.
Remove the retaining bolt(s).
Lift the back (toward the rear of the car) of the seat bottom upwards while rotating it toward the front of the car.
Disconnect the hooks at the front edge (during the rolling motion) of the seat and remove the seat bottom.
Remove the carpet (in the luggage compartment) from the rear of the seat backs.
Remove the seat back mounting bolts from the luggage compartment side.
Lift out the seat back.
If the rear side bolsters or pads are to be removed, remove the lower mounting bolt, then push upward to free the hooks.
Hope this helps you.

Dec 21, 2009 | 1994 Honda Accord

1 Answer

Remove backseat of honda accord 1991


With your hands, press down on the seat cushion where it meets the seat back. Locate the retaining bolt(s). Some models retain the seat with one bolt in the center; others use two, evenly spaced left and right.
Remove the retaining bolt(s).
Life the back (toward the rear of the car) of the seat bottom upwards while rotating it toward the front of the car.
Disconnect the hooks at the front edge (during the rolling motion) of the seat and remove the seat bottom.
Remove the carpet (in the luggage compartment) from the rear of the seat backs.
Remove the seat back mounting bolts from the luggage compartment side.
Lift out the seat back.
If the rear side bolsters or pads are to be removed, remove the lower mounting bolt, then push upward to free the hooks.
Hope this helps you.

Oct 17, 2009 | 1991 Honda Accord

1 Answer

I need to replace a rear seat belt in a 1997 Ford Tarsus. Does any know the best way to access the assembly? In addition, are there any diagrams available that show the connection points?


please don't forget to rate, thx.

Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Safety Belt Bolt Bit T77L-2100A
NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.

Removal
  1. Remove rear seat cushion. Refer to Section 01-10 .
Seat Cushion, Rear Sedan
Removal
  1. Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
  1. Remove rear seat cushion from vehicle.
  1. Remove rear seat back. Refer to Section 01-10 .
Seat Back, Rear 60/40 Split Bench—Sedan
Removal
  1. NOTE: Safety belt bolts do not secure seat back to vehicle.

    Remove rear seat cushion as described.
  1. Fold down back seat and remove two bolts in the center of each seat back striker plates.
  1. Remove two bolts from outboard rear seat back frame retaining brackets.
  1. Lift seat back up and pull forward to remove from vehicle.
  1. Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
Trim Panel, Quarter—Sedan Removal
  1. Remove rear seat. Refer to Section 01-10 .
  1. Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
  1. Pull lower quarter trim panel away from body.
  1. Remove safety belt retaining bolt.
  1. Feed safety belt through lower quarter trim panel.
  1. Remove safety belt anchor plate-to-sill bolt from quarter panel.
  1. Remove retractor anchor nut and retractor from rear quarter panel.
  1. Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
  1. Slide anchor plate end of safety belt through the openings in the quarter trim panel.
  1. Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.


    2a6fac0.gif


    Item Part Number Description 1 386277-S190 Bolt (Part of 611B68) 2 31012 Upper Rear Quarter Trim Panel 3 611B60 Retractor and Tongue 4 N800937-S190 Nut 5 389370-S190 Bolt 6 — Rear Quarter Panel (Part of Body) 7 52018 Lower Rear Quarter Trim Panel 8 — Mounting Stud (Part of Body)
  1. Remove seat belt anchor bolt and retractor and tongue from rear deck panel.


    fff90b0.gif

Installation
  1. To install, reverse Removal procedure.
  1. Make sure the safety belt webbing is not twisted. If it is, remove the twist.
  1. Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).
  1. Check the restraint system for proper operation.

Jun 30, 2009 | 1997 Ford Taurus

1 Answer

Middel seatbelt will not loosen


I think you have to remove headrst bfore folding seat back down. You may have to unbolt seat from floor. 4 bolts.
Rear Seat Backrest —Split Bench Removal
NOTE: The 40% rear seat backrest must be removed before the 60% rear seat backrest.
40% rear seat backrest
  1. Remove the 40% rear seat backrest.
    1. Remove the nuts and bolts.
    1. Remove the backrest.
60% rear seat backrest
  1. Remove the 60% rear seat backrest.
    1. Remove the nut and bolt.
    1. Remove the backrest.
Installation
NOTE: The 60% rear seat backrest must be installed before the 40% rear seat backrest.
60% rear seat backrest
  1. NOTE: Do not tighten the nut and bolt at this time.
    Install the 60% rear seat backrest.
    1. Install the rear seat backrest.
    1. Install the nut and bolt.
40% rear seat backrest
  1. NOTE: Do not tighten the nuts and bolts at this time.
    Install the 40% rear seat backrest.
    1. Install the rear seat backrest.
    1. Install the nuts and bolts.
60/40% rear seat backrest
  1. Tighten the 60/40% rear seat backrest nuts and bolts in the sequence shown.
de01dcf.gif
40% Rear Seat Backrest
  1. Tighten the 40% rear seat backrest nuts and bolts in the sequence shown.

Jun 11, 2009 | 2005 Ford Escape

1 Answer

Rear seatbelt


fold rear down take outter seat off one twelve bolt at bottom remove clps and pck tray YOU GOT IT

Mar 07, 2009 | 1997 Toyota Camry

2 Answers

Gas leaking from on top of the tank


In the 03, the bottom of the back seat has two (2) spring hooks about 12 or so inches from the side (looks like this, o= hook _= front of seat bottom), (_o____o_). Just pull up on each one and the seat bottom will come up and out/forward. The seat back has a couple of bolts that you will see once you remove the seat bottom. Remove bolt(s) and slide the seat back to the outside. There are two (2) "windows" to the tank. One on driver's side that will be visible when you remove the seat bottom (and pull back the carpet and insulation, and one behind the seat-back on the passenger's side (this is where the fuel pump, et. al. is/are. Driver's side is just the second float. There is a wire and hose that connects the two floats, so you may want to disconnect the battery to avoid any electrical current in the tank.

Aug 09, 2008 | 1999 Volvo S80

Not finding what you are looking for?
2002 Mazda Protege Logo

Related Topics:

657 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...