Question about 1998 Toyota Tacoma

1 Answer

Blower reisitor, 1998 Toyota Tacoma

Need to replace blower reaistor, have a new one on hand, need to know how to replace the old one and how to locate it.

Posted by on

  • Anonymous Mar 21, 2014

    location of fuse

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 1,861 Answers

The blower motor resistor is located in the heater box area, which is under the dashboard on the passenger side. You will find the resistor in the large squarish tube that leads to the center of the dash from the blower motor housing (right to left on an american vehicle). Unplug the large black wiring connector, remove the 2 phillips screws and the resistor is ready to pull out of the heater box.

Posted on Sep 19, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you tell me where the knock sensor is located on a 1998 toyota tacoma


depends on engine - dealer will tell u by serial #1.
help on net. however one is located left [to firewall from oil filter.
# 2 could be drivers side under intake manifold in the valley.
So unless want a big job look near the oil filter. oil dender is ahead of the filter..on the block.. But as I sead ask the parts department at a dealer..Good luck.. I had the wire drop off on my 89 3 liter v6 .was of roading just by the oil filter.. stick I guess.
cowcamp

Sep 20, 2014 | 1998 Toyota Tacoma

1 Answer

Blower resistor Toyota Tacoma 2007 where is locater . How i can replace.


Might be the Resistor pack located close to the blower. Could be under the dash or under the hood, but always close to the blower itself. Usually has a flat connector with 4 or 5 wires, and two small screws holding in the duct. It may be a crispy critter. It happens... The blower moves air across it to keep it cool. The blower motor may be bad as well, or possibly the fan speed switch. May very well be the fuse for the blower as well. The blower connector may be loose. Let me know what you find.

Dec 02, 2012 | 2007 Toyota Tacoma Double

1 Answer

How often do i need to change timing chain in my 1998 toyoota tacoma


you shouldn't need to unless the chain is noisy

Oct 07, 2012 | Cars & Trucks

2 Answers

What could cause a low rpm hesitation or an acceleration hesitation on a 1998 toyota tacoma 4 cylinder 4X4


u could very well need a new fuel pump or fuel pressure regulator, or u might just need a full tune-up done

Jun 16, 2010 | 1998 Toyota Tacoma

1 Answer

Location of the fuel filter on 2000 toyota tacoma 2 wd std cab


Oil filter on a 2000 Toyota Tacoma Prerunner with 6 cylinder IS a screw on filter located on the drivers side front of the engine (just beneath the alternator).

Can't recall the size but, you need a socket with extension to get to the bolts holding the skid pan then, wiggle/lift it from it's hooks. Then, you can either cuss, cuss, cuss while removing the old and installing the new OR, jack the drivers side up 4 to 6 inches ( gives you a bit more wiggle room and keeps you from scraping your elbow to the bone on whatever surface you're working on).

Even then, be ready for a good cussing bout because there still isn't much room.

May 19, 2010 | 2000 Toyota Tacoma PreRunner

1 Answer

My AC/Heater fan blower just works on high, but when I hit a bump big enough to cause a significant vibration, I can use the other speeds (low, medium etc...). If I hit the bump again it'll just work on...


wiggle the wires behind the control unit to see if maybe there's a loose wire. If that does not work, then try tapping the climate control switch, if it works then you know it's your switch that needs to be replaced. If you want to fix it yourself, just take it out and dissasemble it and clean the unit with alcohol or nail polish remover and try it again on the part (knob) that makes contact with the board. a new unit is very expensive.

May 10, 2010 | 2005 Toyota Tacoma

1 Answer

How do I replace the spark plugs on my 1998 Toyota Tacoma 6 cylinder truck?


you need the tool to take them out first. then you have leads that clip on to each one pull one off then unscrew the first spark plug then replace with new one then put the lead on that you took off. DO THIS ONE AT A TIME THOUGH AS THEY HAVE TO BE IN A SEQUANCE. and make sure they are spark plugs u want and not heater plugs that are on deisel veichals. if this helps please leave feed back thanks

Oct 22, 2009 | 1998 Toyota Tacoma

2 Answers

1997 Toyota Tacoma v6/4x4/manual: Clutch petal/Clutch


I currently have a 1998 Toyota Tacoma, and the clutch pedal does not return all the way. I know it is not the clutch, it is actually the spring located underneath the pedal. It is catching and not releasing after pushed.... Hope it helps.

Jun 19, 2009 | 1998 Toyota Tacoma

2 Answers

Drivers door wont latch


open yor inner door panel most of the time it is a lock rod, or plastic socket that holds it in place might of broken, or simply jarred loose if slammed hard. on older cars.

shack

Apr 14, 2009 | 1998 Toyota Tacoma

2 Answers

2003 Toyota Tacoma


The blower motor is located directly below the passanger glove box on the right. Its a round flat plate with 2 small screws holding it in place. All you need is a screwdriver and a pair of wire cutters (the wire cutters totally depend on whether the replacement is factory or not.) Simply unblot the existing part and replace it with the new part. If you have purchased an aftermarket part you will need to cut and attach the factory harness pigtail to your motor. Also the replacement part I purchased didn't come with the blower wheel, so I had to remove the old one and place it on the new motor. Works like a charm! Easy install and best of all....I have air after 2 years without!!

Jun 20, 2008 | 2003 Toyota Tacoma

Not finding what you are looking for?
1998 Toyota Tacoma Logo

445 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...