Question about 1996 Ford Taurus

1 Answer

Good Morning Dear Sir, Have a little problem with my 1996 Ford Taurus 2 cycle and Misfire. Can you tell whay should I do. E-mail back thomas.locke@navy.mil Thomas

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

What is a Taurus 2 cycle??? When does it misfire? Report fully!

Quick and simple solution is change the spark plugs, use the plain platinum type, and the spark plug wires. When installing the plugs, be sure to use antiseize compoud on the plug threads before installing them. The proper spark plug gap will be listed on a sticker label under the hood. It helps to remove them air filter assembly and duct work to get easier access to the back three plugs.

Posted on Nov 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

96 ford Taurus. took it in for smog and failed, code said we needed to replace the camshaft position censor, so we did. it ran a little better. took it back in after 50 miles and now getting the p0302 code...


Codes do not tell you what to replace.
The cam sensor most likely was okey

PO302--as you said, is a misfire on cylinder #2,work on that problem
Spark plug wire,bad coil pack,etc.

Seek professional help,it will be quicker,cheaper in the long run, and they can verify it will pass inspection.

OBD Codes and check lights,only indicate a possible system malfunction
Then you need the knowledge, to diagnose the system ,and find the cause of the MIL Lamp being on

Nov 06, 2010 | Ford Taurus Cars & Trucks

1 Answer

97 ford taurus: Cylinder 2 misfire


well..fuel injection systems are more than the electronic part. I suspect you are dealing with compression or injector fouling issues..

Oct 21, 2008 | 1997 Ford Taurus

2 Answers

Where is cylinder #3


Several engine here, check this...

1996 Ford Taurus 3.0 liter V-6 VIN "2"
1996 Ford Taurus 3.0 liter V-6 VIN "U"

0af0d32.gif


1996 Ford Taurus 3.0 liter V-6 DOHC VIN "S"

d50d351.gif


1996 Ford Taurus 3.4 liter DOHC V-8 VIN "N"

41d2714.gif

Hope this helped (remember voted and rated this). Good luck.

Feb 10, 2010 | 1996 Ford Taurus

1 Answer

Misfire on the #2 spark plug


Firing order is 1-4-2-5-3-6 Cylinders are numbered as such: Standing in front of the car looking at the engine the cylinders farthest from you on the back side of the engine are from left to right, 1-2-3 and on the front side closest to you from left to right 4-5-6.

Sep 16, 2009 | 2003 Ford Taurus

1 Answer

2000 Ford Taurus 6 cylinder with the alternate


i would check the fuel injector o # 5 cyl... if the injector is leaking it will foul the plug out and cause a skip. the next time it happens remove the plug and check for wetness. you may also be able to put a fuel pressure tester on, if so install the tester, turn the key on 2 or 3 times leaving the key in the on position at the end, do not crank the engine, watch the tester for a minute or so and watch for a pressure drop.

May 18, 2009 | 2000 Ford Taurus

1 Answer

Car kills if put into reverse or drive


replace the neutral safety switch

Apr 17, 2009 | 1996 Ford Taurus

1 Answer

Engine light on. Had it tested came up as ''misfire on cylinder 4''


A misfire is when the fuel is not ignited in the cylinder of the motor.Pretty much the car would be running on 5 cylinders. most of the time, you should just need to replace the plugs and wires. And that should solve the problem.

Mar 19, 2009 | 2003 Ford Taurus

1 Answer

1996 Ford Taurus 3.0 v6


Check the fluid as recommended by Ford. Do u have the owners manual? It will give the procedure. I'm quite sure your Taurus trans fluid is checked at operating temp w/ engine running, in park. U can also check the dipstick, Ford usually has the procedure engraved on the dipstick. The reason for checking the fluid as Ford tells u to, is because their method will give an accurate reading. As u can see from checking the fluid in 2 different ways, u got totally different readings.

Oct 20, 2008 | 1996 Ford Taurus

2 Answers

98 ford taurus dohc


You have to remove the parts that are in the way, then lay on top of the engine to get at the plugs, you will need a good spark plug boot removal tool as well or you will tear the plug boots, the plugs don't need changing until 100,000 miles.

Oct 03, 2008 | 1996 Ford Taurus

3 Answers

Error code p0303 cylinder 3 misfire


po303 is misfire on number 3 cylinder. It could be a bad spark plug or wire, maybe a loose plug wire, could be alot of things. injector problem drop of water in fuel that happened to hit that cylinder. but most likely a plug misfired. I would clear the code and see if it happens again. If so give care a tune up.

Aug 09, 2008 | 1999 Ford Taurus

Not finding what you are looking for?
1996 Ford Taurus Logo

Related Topics:

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...