Question about 2002 Jeep Grand Cherokee

1 Answer

Turn signal how do i get to the flasher and check it? is there a seperate flasher for the hazards since the hazards work fine?

Posted by on

  • Anonymous Sep 24, 2008

    Intermittantly the signal lites will not work. Hazards DO work and it appears to be the method to get them going but only if you leave the flashers on for 10 min. or so. I have replaced all the bulbs, the multi-function switch, checked fuses but cannot locate the relay (possibly behind the dash) very awkward access and I have dismanteled the dash panels as well to get access.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Jeep Master
  • 61,129 Answers

The turn and 4 way are seperate, turn on the 4 way and follow the sound, it will be near the steering column.

Posted on Sep 21, 2008

5 Suggested Answers

  • 40 Answers

SOURCE: turn signal and hazards wont work

Do you have a trailer wiring harness? If you do, recheck the wiring there. If that doesn't help and you have properly checked the flashers then you need to check each bulb

Posted on Jul 03, 2009

  • 4 Answers

SOURCE: 1997 Chevy Tahoe both turn signals stopped working

Sounds like the flasher unit to me. Normally the emergency flasher and turn signal are separate.

Posted on Jul 21, 2009

motor1258
  • 6674 Answers

SOURCE: Hazard flashers do not work but the turn signals

Should be in same general area. Check fuse panel under dash, and along side of steering column. What year?

Posted on Jul 23, 2009

  • 630 Answers

SOURCE: 1992 sedan deville turn signals out....

Yes they use a different flasher unit for the turn signals,

Posted on Nov 27, 2009

Stu_26
  • 102 Answers

SOURCE: on a base model 1994

no i have a 94 ga too and last year i had the same problem i just replaced the whole switch (hazzards and blinkers are all in one) and the problem was gone

Posted on Feb 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My turn signals works sometimes and then wont work at all


Drivers side of steering column under dash, check flasher make sure its tite, turn key to on, turn signal on, move flasher round see if turn signal starts working replace flasher try it agian might be bad connection

Feb 18, 2013 | 1998 Cadillac Eldorado

1 Answer

Blinkers dont work on my 1989 mitsubishi mirage but hazards do?


Turn signals are operated by a different fuse then the hazard flasher - start by checking the fuses - if they are okay you may have a seperate flasher unit for the turn signals too - you may need to replace the flasher unit - hope this helps - good luck :O)

Feb 21, 2011 | 1989 Mitsubishi Mirage

2 Answers

Where is the turn signal flasher located?


You more likely have a bulb that is no good. The next time your signals aren't working, pull over and check to see which bulb isn't working. Make sure the turn signal is on while checking. It should only be the left or right. Not both. Sometimes you can see the blown bulb with the hazards on depending on your model vehicle. Simply check the bulb thats not blinking for a tight fit. Then replace it if thats not the cure.

Apr 30, 2010 | 2006 Chrysler Town & Country

1 Answer

Turn signals not working audi a6 2002


turn signal switch most likely. But it could have a faulty flasher relay. the signals and the hazards probably have seperate flasher relays and possibly on different circuits so check fuses as well

Nov 04, 2009 | 2002 Audi A6

1 Answer

Haz flashers wont work but blinkers do


There are 2 seperate flashers 1 for turn signals and 1 for hazard.The hazard flasher is located in the convenance center the turn flasher in the fuse box. Also seperate fuse's for each. One battery circuit for hazard Ignition for turn signals.Check fuse for hazard,if good try swapping in the turn signal flasher and see if hazards work.They use the same flasher unit.

Aug 20, 2009 | 1993 GMC Safari

1 Answer

1997 Chevy Tahoe both turn signals stopped working


Sounds like the flasher unit to me. Normally the emergency flasher and turn signal are separate.

Jul 21, 2009 | 2001 Chevrolet Tahoe

1 Answer

Turn signals not working. How do I know if it is


first check the fuse,then the flasher, the hazard flasher is a seperate flasher, then check the swtich

Jul 15, 2009 | 1994 Lincoln Town Car

1 Answer

My hazards in my 1997 camaro rs work, but the back and front turn signals dont. The lights for the signals dont work in the dash either, just the lights for the hazards


check the signal flasher ( little silver or colored can in fuse panel or under dash. 4 ways have 1 flasher and the signals have a seperate flasher. Put hazards on to hear click, to determine which flasher is which. Hope this helps

Apr 13, 2009 | 1997 Chevrolet Camaro

1 Answer

Hazards work turn signals dont


check your flasher the Hazards have a seperate flasher its a littl cube that looks like a relay in or near the fuse box

Apr 07, 2009 | 1987 Pontiac Firebird

Not finding what you are looking for?
2002 Jeep Grand Cherokee Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...