Question about 2003 Lincoln Navigator

1 Answer

AIR SUSPENSION QUIT

SUDDENLY THE AIR SUSPENSION QUIT.
I FOUND ON THE NET IN REFERENCE TO AN
AIR SUSPENSION RELAY SWITCH.
WHERE IS IT LOCATED?

CAN I DO THIS MY SELF OR IS IT AN DEALER/DEAL?
lkah1218@aol.com

Posted by on

  • 2 more comments 
  • RHONDA KAHN Sep 20, 2008

    FELT LIKE RIDING A BRONCO BULL !!!

  • selest55 Feb 23, 2009

    The check suspension light went on so I turned off the switch that is located on the passenger side and then I turned it on again and the light went off but the air suspension did not go on. Now my Expedition rides the bumps on the road like an old truck. I tried checking the fuses but that did not help and I don't have a manuel to check which is the fuse or where the relays are.

  • nicmotto May 21, 2009

    Same problem here!  replaced fuses, replaced the air suspension pump. Now what?? it's still sitting on front wheels & will not lift up. 

  • erik mcdonald
    erik mcdonald May 11, 2010

    there is a deactivator switch that if you fallow up the brake pedal its back by the top of the pedal and towards the driver seat behind the lower dash, theres a module box that is around there also. there is a air suspention service switch there is an air suspention relay, there is the compressor itself. what do you want to know? where which is at, what they do?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 3 Answers

TOOK IT TO A LINCOLN DEALER:
REPLACED AIR SUSPENSION PUMP
(THEY FOUND PUMP TO BE "SUDDENLY"BURNED OUT) (heart-attack)...
1.) 6L1Z*5319*AA COMPRESSOR $433.10
2.) LABOR 287.00

YUCK $$$ GONE/ +TAX...

NEEDED TO HAPPEN/ FRAME WAS ON FRONT WHEELS/WOULD NOT LIFT.

THANKX FOR THIS FORUM...

lkah1218@AOL.COM


Posted on Sep 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear suspension will deflate but why won't it inflate?


That could work , You mite be able to test the sensor in question with ohm meter . Test the front one an see what the resistance is ,then check the back one. I don't know what it should be with out looking it up in the service info . You could also check to see if the sensor is getting power from the control module , an see if there is a return input to the module .
There are a few DTC'S this able to set !
Air Suspension Control Module Diagnostic Trouble Code (DTC) Index
Air Suspension Control Module Diagnostic Trouble Code (DTC) Index DTCs Description Source Action B1318 Battery Voltage Low Air Suspension Control Module Go To Pinpoint Test C . B1342 Air Suspension Control Module Air Suspension Control Module INSTALL a new air suspension control module. REFER to Module-Air Suspension Control . SET the front ride height. REFER to Air Suspension Initialization (Clear DTC B2140). CLEAR the DTCs. REPEAT the self-test. B1485 Brake Pedal Input Circuit Battery Short Air Suspension Control Module RERUN On-Demand Self-Test. MAKE SURE that the brake pedal is not pressed. If DTC is returned again, REPAIR brake pedal position (BPP) circuitry. B1566 Door Ajar Circuit Short to Ground Air Suspension Control Module Go To Pinpoint Test D . B2140 Initialization Failure (Vehicle Ride Height Not Programmed) Air Suspension Control Module REFER to Air Suspension Initialization (Clear DTC B2140). C1439 Vehicle Acceleration EEC-V Circuit Failure Air Suspension Control Module Go To Pinpoint Test E . C1724 Air Suspension Height Sensor Power Circuit Failure Air Suspension Control Module Go To Pinpoint Test F . C1726 Air Suspension Pneumatic Failure Air Suspension Control Module Go To Pinpoint Test G . C1760 Air Suspension Height Sensor High Signal Circuit Failure Air Suspension Control Module Go To Pinpoint Test H . C1770 Air Suspension Vent Solenoid Output Circuit Failure Air Suspension Control Module Go To Pinpoint Test I . C1790 Air Suspension LR Air Spring Solenoid Output Circuit Failure Air Suspension Control Module Go To Pinpoint Test J . C1795 Air Suspension RR Air Spring Solenoid Output Circuit Failure Air Suspension Control Module Go To Pinpoint Test K . C1830 Air Suspension Compressor Relay Circuit Failure Air Suspension Control Module Go To Pinpoint Test L . C1917 Steering Electronic Variable Orifice (EEVO) Out-of-Range Fault Air Suspension Control Module Go To Pinpoint Test Q .
  • Uneven vehicle height
  • Circuitry.
  • Rear pneumatic fault.
  • Air compressor assembly.
  • Air suspension control module.
  • Go To Pinpoint Test I .

Nov 06, 2015 | 2002 Lincoln Navigator

3 Answers

The rear suspension air bags no work


start here

The air suspension system is designed to improve ride, handling and general vehicle performance for static, on-road and off-road driving condition:
  • Ride is improved by using an air type spring (the soft ride is inherent).
  • Handling is improved by maintaining constant vehicle attitude.
The system consists of unique rear air springs, air compressor, air lines, air spring solenoids, height sensor, air suspension control module, attachments and associated signals derived from both driver and road inputs. With these components and signals, the air suspension control module commands changes in vehicle height that are necessary for the load leveling features.
The load leveling feature rear air suspension (RAS) systems shall automatically make adjustments in vehicle height so that the vehicle is always at trim height and constant front-to-rear vehicle attitudes are maintained over the expected load range of the vehicle. Adjustments in height that are necessary to correct height differences between the vehicle's left and right sides for RAS system shall be restricted to what can be reliably achieved with one air suspension height sensor.
The system uses one air suspension height sensor, a steering sensor, generic electronic module (GEM) transfer case inputs, and other vehicle sensors to measure driver and road inputs. The system changes vehicle height using an air compressor, two air lines, and the use of an air spring with an air spring solenoid.
The air suspension system holds vehicle height when the rear hatch or any door is opened. The system stores rear vehicle height the moment any open door is detected. The system then maintains this height regardless of the addition or removal of a load. The system will return to its commanded height when all doors are closed and the vehicle speed exceeds 16 km/h (10 mph).
Air Suspension Switch
The air suspension switch is located behind the RH kick panel on a mounting bracket. The switch interrupts power to the air suspension control module.
The air suspension switch supplies a signal to the air suspension control module. Without the air suspension control module receiving this signal the load leveling system is inoperative and will not react when rear of the vehicle is raised or lowered. If the air suspension system is disabled by turning off air suspension switch, a "CHECK SUSP" will appear in the RH corner of the instrument cluster with the ignition in the run position.
Air Compressor
The RAS air compressor:
  • Is not interchangeable with four wheel air suspension (4WAS) compressor.
  • Consists of the compressor and vent solenoid; neither are replaceable as individual items.
  • Is mounted in the engine compartment between the washer fluid bottle and headlamp (RH front corner).
  • Is a single cylinder electric motor driven unit that provides pressurized air as required.
  • Is powered by a solid state relay, controlled by the air suspension control module.
  • Passes pressurized air through the compressor air drier that contains silica gel (a drying agent). Moisture is then removed from the compressor air drier when vented air passes out of the system during vent operation.
  • Air drier has a single port and is not interchangeable with 4WAS compressor air drier.
  • Air drier may be replaced separately.
  • Incorporates a snorkle that may be replaced separately.
The vent solenoid:
  • Allows air to escape from the system during venting actions.
  • Is located in the air compressor cylinder head.
  • Has a 160 psi internal relief valve.
  • Shares a common electrical connector with the air compressor motor.
  • Is enclosed in the cylinder head casting, which forms an integral valve housing that allows the valve tip to enter the pressurized side of the system.
  • Has an O-ring seal that prevents air leakage past the valve tip.
  • Opens when the air suspension control module determines lowering is required.
  • Provides an escape route for pressurized air that opens when system pressures exceed safe operating levels.
  • Is replaced with the air compressor as a unit.
Air Spring
RAS vehicles use air springs in the rear. The air springs provide a varying spring rate proportional to the systems air pressure and volume. The air suspension system regulates the air pressure in each air spring by compressing and venting the system air. Increasing air pressure (compressing) raises the rear of the vehicle while decreasing air pressure (venting) lowers the rear of the vehicle. Vehicle height is maintained by the addition and removal of air in each air spring through an air spring solenoid installed in the upper spring cap and energized through the air suspension control module.
The air springs are mounted between the axle spring seats and the frame upper spring seats.
The two air springs replace the conventional rear coil springs.
Air Suspension Height Sensor
When the air suspension height sensor indicates that the rear of the vehicle is lower than trim under normal driving conditions, the air compressor will turn on and pump compressed air to the air springs. When the sensor indicates that the rear of the vehicle is raised above trim under normal driving conditions, this will cause the air to be vented from the air springs to lower the vehicle back to its trim height level.
One air suspension height sensor is mounted on the vehicle. The air suspension height sensor sends a voltage signal to the air suspension control module. The output ranges from approximately 4.75 volts at minimum height (when the vehicle is low or in full jounce), to 0.25 volts at maximum height (when the vehicle is high or in full rebound). The air suspension height sensor has a useable range of 80 mm (3 in) compared to total suspension travel of 200-250 mm (8 to 10 in) at the wheel. Therefore, the air suspension height sensor is mounted to the suspension at a point where full rear suspension travel at the wheel is relative to 80 mm of travel at the air suspension height sensor. The air suspension height sensor is attached between the No. 5 frame crossmember (upper socket) and the panhard rod (lower socket). Replace the air suspension height sensor as a unit.
Compressor Relay
The compressor relay is energized by the air suspension control module to allow high current to flow from the battery to the compressor motor.
  • A solid state relay is used in the air suspension system for air compressor control. The relay incorporates a custom power metal oxide semi-conductor field effect transistor (MOSFET) and ceramic hybrid circuitry. The relay switches high current loads in response to low power signals and is controlled by the logic of the air suspension control module.
Air Suspension Control Module
NOTE: The 4WAS air suspension control module is used for the RAS system. The internal processor recognizes external circuitry to determine if it is installed in a 4WAS or a RAS equipped vehicle.
NOTE: The air suspension control module is calibrated with information from the air suspension height sensor. A new or exchanged air suspension control module requires a ride height adjustment calibration process to be performed.
The air suspension control module controls the air compressor motor (through a solid state relay), and the air spring solenoids. The air suspension control module also provides power to the air suspension height sensor. The air suspension control module controls vehicle height adjustments by monitoring the air suspension height sensor, vehicle speed, a steering sensor, acceleration input, the door ajar signal, transfer case signals, and the brake pedal position (BPP) switch. The air suspension control module also conducts all fail-safe and diagnostic strategies and contains self-test and communication software for testing of the vehicle and related components.
The air suspension control module is mounted in the passenger compartment inside the instrument panel above the radio and temperature controls.
The air suspension control module monitors and controls the air suspension system through a 32-pin two-way connector. The air suspension control module is keyed so that the air suspension control module cannot be plugged into an incorrect harness. There are two sides of the harness connection to the air suspension control module. Each is uniquely colored and keyed to prevent reversing the connections.
Air Suspension Diagnostic Connector
The air suspension diagnostic connector is used to aid the technician in diagnosing the air suspension system. It is also used to vent the system of compressed air when air suspension system components need to be repaired or replaced. The air suspension diagnostic connector is located under steering column.

Oct 02, 2009 | 1998 Ford Expedition

1 Answer

2002 linncoln towncar where is the air supension compressor relay switch,please.


Air suspension needs compressed air for the control of Air Springs (Air Spring is a cylinder like thing which goes up and down when air is pumped in and out of it). For pumping in and out the air, air compressor needs to be switched ON/OFF. Compressor relay connects and disconnects the compressor motor from the power supply ( battery). ----------------- air ride suspension compressor located under the air filter box . ---------------- the Air compressor clutch relay location
is fitted to the left hand inner wing (when viewed from the the driving seat).
-------------------
the compresser is located on the left hand side of the car under the hood.
once you open the hood remove the air cleaner housing and windshield washer resivor.
there is a panel that you lift up under both of thoese that is where the compresser is located
-------------
  1. The air suspension uses a small, separate air compressor under the driver's side left fenderwell, with air lines running to the air bags. On the top of each air bag is a electrical valve. This is a relief valve that allows air to be exhausted when activated, and which senses the amount of air pressure within the air bag to keep both sides equal. These valves are operated via a leveling sensor that is attached to the body of the car and to the rear axle by a movable arm. When the rear of the car drops due to increased load, the arm is pushed up. When the arm is pushed up, it turns on the air compressor and fills the air bags to level the car. When the load is removed and the arm moves down, indicating that the back of the car has risen, the sensor opens the valve on the air bags and allows air to escape, lowering the car.
  2. If the back of the car is low, indicating that the air suspension is not working, and the air suspension light is on, check the fuse first. If the fuse is all right, check the air suspension switch in the trunk and make sure it is on. This switch is used when the car is in for service. Always turn off the switch before lifting the car, because the sensor will think the car is rising and keep the air bag valves open, ruining the rear air suspension.
  3. Turn the ignition key with the engine off. Listen for the compressor to come on while pushing down on the rear bumper. If it does not come on, test the switch terminals for power, using a circuit tester. If one terminal has power and the other does not, replace the switch. If there is power, turn the switch to the off position, raise the vehicle and place it on jack stands in the rear. Inspect the leveling switch on the axle, making sure it is not bent and is connected. Use an ohmmeter for this test. Pull the electrical connector off the switch. Loosen the arm of the switch from the axle. Test the switch with the ohmmeter by checking across both terminals while slowly moving the arm. There should be no continuity with the arm down. As the arm is raised, there should be continuity. If not, replace the switch. If there was continuity, connect the arm and the electrical connector.
  4. Put a floor jack under the axle and raise the axle to the point where it is just beginning to lift the car off the jack stand. Turn on the ignition. Turn the air suspension switch to the "on" position. Use the circuit tester to check for power at the leveling switch. If there is power, turn the air suspension switch to "off" and lower the car. Access the air compressor in the front, under the hood, and check the electrical connector for power. If there is power, check for a good ground. If both are good, replace the compressor. If the compressor works and the car does not rise in the back, replace the air bags.


Sep 11, 2009 | 2002 Lincoln Town Car

3 Answers

Rear air bag suspension failure 1998 Ford EXP E.B. 2x2


this will get you started. report back on progress and we'll go from there. There is a diagnostic test that will provide codes I think. I will look.

The system consists of unique rear air springs, air compressor, air lines, air spring solenoids, height sensor, air suspension control module, attachments and associated signals derived from both driver and road inputs. With these components and signals, the air suspension control module commands changes in vehicle height that are necessary for the load leveling features.
The load leveling feature rear air suspension (RAS) systems shall automatically make adjustments in vehicle height so that the vehicle is always at trim height and constant front-to-rear vehicle attitudes are maintained over the expected load range of the vehicle. Adjustments in height that are necessary to correct height differences between the vehicle's left and right sides for RAS system shall be restricted to what can be reliably achieved with one air suspension height sensor.
The system uses one air suspension height sensor, a steering sensor, generic electronic module (GEM) transfer case inputs, and other vehicle sensors to measure driver and road inputs. The system changes vehicle height using an air compressor, two air lines, and the use of an air spring with an air spring solenoid.
The air suspension system holds vehicle height when the rear hatch or any door is opened. The system stores rear vehicle height the moment any open door is detected. The system then maintains this height regardless of the addition or removal of a load. The system will return to its commanded height when all doors are closed and the vehicle speed exceeds 16 km/h (10 mph).
Air Suspension Switch
The air suspension switch is located behind the RH kick panel on a mounting bracket. The switch interrupts power to the air suspension control module.
The air suspension switch supplies a signal to the air suspension control module. Without the air suspension control module receiving this signal the load leveling system is inoperative and will not react when rear of the vehicle is raised or lowered. If the air suspension system is disabled by turning off air suspension switch, a "CHECK SUSP" will appear in the RH corner of the instrument cluster with the ignition in the run position.
Air Compressor
The RAS air compressor:
  • Is not interchangeable with four wheel air suspension (4WAS) compressor.
  • Consists of the compressor and vent solenoid; neither are replaceable as individual items.
  • Is mounted in the engine compartment between the washer fluid bottle and headlamp (RH front corner).
  • Is a single cylinder electric motor driven unit that provides pressurized air as required.
  • Is powered by a solid state relay, controlled by the air suspension control module.
  • Passes pressurized air through the compressor air drier that contains silica gel (a drying agent). Moisture is then removed from the compressor air drier when vented air passes out of the system during vent operation.
  • Air drier has a single port and is not interchangeable with 4WAS compressor air drier.
  • Air drier may be replaced separately.
  • Incorporates a snorkle that may be replaced separately.
The vent solenoid:
  • Allows air to escape from the system during venting actions.
  • Is located in the air compressor cylinder head.
  • Has a 160 psi internal relief valve.
  • Shares a common electrical connector with the air compressor motor.
  • Is enclosed in the cylinder head casting, which forms an integral valve housing that allows the valve tip to enter the pressurized side of the system.
  • Has an O-ring seal that prevents air leakage past the valve tip.
  • Opens when the air suspension control module determines lowering is required.
  • Provides an escape route for pressurized air that opens when system pressures exceed safe operating levels.
  • Is replaced with the air compressor as a unit.
Air Spring
RAS vehicles use air springs in the rear. The air springs provide a varying spring rate proportional to the systems air pressure and volume. The air suspension system regulates the air pressure in each air spring by compressing and venting the system air. Increasing air pressure (compressing) raises the rear of the vehicle while decreasing air pressure (venting) lowers the rear of the vehicle. Vehicle height is maintained by the addition and removal of air in each air spring through an air spring solenoid installed in the upper spring cap and energized through the air suspension control module.
The air springs are mounted between the axle spring seats and the frame upper spring seats.
The two air springs replace the conventional rear coil springs.
Air Suspension Height Sensor
When the air suspension height sensor indicates that the rear of the vehicle is lower than trim under normal driving conditions, the air compressor will turn on and pump compressed air to the air springs. When the sensor indicates that the rear of the vehicle is raised above trim under normal driving conditions, this will cause the air to be vented from the air springs to lower the vehicle back to its trim height level.
One air suspension height sensor is mounted on the vehicle. The air suspension height sensor sends a voltage signal to the air suspension control module. The output ranges from approximately 4.75 volts at minimum height (when the vehicle is low or in full jounce), to 0.25 volts at maximum height (when the vehicle is high or in full rebound). The air suspension height sensor has a useable range of 80 mm (3 in) compared to total suspension travel of 200-250 mm (8 to 10 in) at the wheel. Therefore, the air suspension height sensor is mounted to the suspension at a point where full rear suspension travel at the wheel is relative to 80 mm of travel at the air suspension height sensor. The air suspension height sensor is attached between the No. 5 frame crossmember (upper socket) and the panhard rod (lower socket). Replace the air suspension height sensor as a unit.
Compressor Relay
The compressor relay is energized by the air suspension control module to allow high current to flow from the battery to the compressor motor.
  • A solid state relay is used in the air suspension system for air compressor control. The relay incorporates a custom power metal oxide semi-conductor field effect transistor (MOSFET) and ceramic hybrid circuitry. The relay switches high current loads in response to low power signals and is controlled by the logic of the air suspension control module.
Air Suspension Control Module
NOTE: The 4WAS air suspension control module is used for the RAS system. The internal processor recognizes external circuitry to determine if it is installed in a 4WAS or a RAS equipped vehicle.
NOTE: The air suspension control module is calibrated with information from the air suspension height sensor. A new or exchanged air suspension control module requires a ride height adjustment calibration process to be performed.
The air suspension control module controls the air compressor motor (through a solid state relay), and the air spring solenoids. The air suspension control module also provides power to the air suspension height sensor. The air suspension control module controls vehicle height adjustments by monitoring the air suspension height sensor, vehicle speed, a steering sensor, acceleration input, the door ajar signal, transfer case signals, and the brake pedal position (BPP) switch. The air suspension control module also conducts all fail-safe and diagnostic strategies and contains self-test and communication software for testing of the vehicle and related components.
The air suspension control module is mounted in the passenger compartment inside the instrument panel above the radio and temperature controls.
The air suspension control module monitors and controls the air suspension system through a 32-pin two-way connector. The air suspension control module is keyed so that the air suspension control module cannot be plugged into an incorrect harness. There are two sides of the harness connection to the air suspension control module. Each is uniquely colored and keyed to prevent reversing the connections.
Solenoid Valve, Air Spring
swj~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Never rotate an air spring solenoid valve to the release slot in the end cap fitting until all pressurized air has escaped from the spring to prevent damage or injury.
The air spring solenoid:
  • allows air to enter and exit the air spring during leveling operations.
  • is electrically operated and controlled by the air suspension control module.
Air Suspension Diagnostic Connector
The air suspension diagnostic connector is used to aid the technician in diagnosing the air suspension system. It is also used to vent the system of compressed air when air suspension system components need to be repaired or replaced. The air suspension diagnostic connector is located under steering column.

Jun 01, 2009 | 1998 Ford Expedition

1 Answer

Where is the relay for the air pump located on the air suspension?


Located front center of engine compartment, above the right cooling fan.

May 23, 2009 | 2000 Ford Expedition

1 Answer

REPLACED DRYER ON 96 CONT NOW THE BACK WONT AIR UP FRONT DOES


maybe you got dirt in the line to the rear. Here's some background info:

The air suspension system includes the following major components:
  • Air compressor to supply air to the air springs (part of front spring and shock and rear spring and shock absorber assemblies
  • Front spring and shock (3C098) and rear spring and shock absorber (5A965) at each corner of the vehicle
  • Four linear air suspension height sensors (5359): two rear and two front height sensors to maintain the vehicle at the proper ride height; only LH rear height sensor is used for air suspension.
  • Dual-mode front spring and shock and rear shock absorber assemblies with internal actuator.
All system functions are controlled by vehicle dynamics control module (5A919). This control module receives inputs from several different sources. These inputs include:
  • vehicle speed via multiplex communication network
  • ignition switch position
  • door position via multiplex communication network
  • height sensor position
  • air suspension service switch
  • engine rpm via multiplex communication network
  • ride and steering personality settings via multiplex communications network
Communications monitor system operation and allow diagnosis of any concerns that may develop in the system.
  • System monitoring for the driver's use is provided through the instrument panel mounted message center indicator (10D898).
  • Diagnosis communication for the service technician is provided through the data link connector (14489) (DLC) under the instrument panel and Rotunda New Generation Star (NGS) Tester 007-00500 or equivalent.
The message center indicator will display AIR LEVELING DISABLED or CHECK RIDE CONTROL if the suspension system is not turned on or the vehicle dynamics control module detects a concern. If air leveling system disabled is displayed, check that air suspension service switch is in the ON position.
-------------------------------------------------------
Weight Added When weight is added to the vehicle, the air suspension system responds as follows:
  • Air suspension height sensor length is reduced from trim length, sending a "vehicle is low" signal to the vehicle dynamics control module (5A919).
  • To restore vehicle to the trim position, the vehicle dynamics control module turns the compressor on by grounding the compressor relay control Circuit 420 (DB/Y). The relay is ground-side switched.
  • To allow pressurized air to enter the rear spring (5560) and front spring and shock (3C098), the control module opens the solenoid valves (5311).
  • Compressed air flows from the compressor, through the compressor air drier assembly, air lines and solenoid valves into the air springs.
  • As the air springs raise the body height, the air suspension height sensor (5359) increases in length until the preset trim height is reached.
  • The vehicle dynamics control module then turns off the compressor (through the relay) and closes the air spring solenoid valves.
  • ----------------------------------------------------------------------------
  • Weight Removed When weight is removed, the air suspension system responds as follows:
    • Air suspension height sensor length is increased from the trim length, sending a "vehicle is high" signal to the control module (5A919).
    • To restore the vehicle to the trim position, the vehicle dynamics control module opens the vent solenoid valve (located in the compressor assembly) and opens the solenoid valves (5311).
    • Compressed air flows from air springs, through the solenoid valves, air lines, compressor air drier (5346) and out the vent solenoid valve.
    • As the body lowers, the air suspension height sensor length decreases until the preset trim height is reached.
    • The vehicle dynamics control module then closes the vent and solenoid valves.
------------------------------------------------------------------------------
Control Module Power and Ground The vehicle dynamics control module (5A919) is located above the upper luggage compartment trim panel and lower module tray. Module power is provided by Circuit 418 (DG/Y) at Pins 36, 37, 56, 57, 58 and is powered through a Fuse 7 (30A) in power distribution box. Module ground is provided through control module wire harness Pins 6, 39, 40 and 60. The data link connector (14489) (DLC) is located in the passenger compartment under the instrument panel, 300 mm (12 inches) right of the steering column. This connector allows communications between the vehicle dynamics control module and either Rotunda New Generation Star (NGS) Tester 007-00500 or equivalent or Rotunda Service Bay Diagnostics System (SBDS)® 001-00001 or equivalent. When the CHECK RIDE CONTROL message is displayed in the message center indicator (10D898), a system error has been detected by the vehicle dynamics control module and is stored in the control module. This diagnostic trouble code (DTC) will be retained for the next 80 ignition switch cycles. If there is no repeat of the same error during these 80 ignition switch cycles, the control module will erase the DTC. Because of this self-erasing memory, a customer may have had a concern "just a few days ago" that is not retrieved from memory when Diagnostic Test Mode (DTC) "Retrieve/Clear Continuous DTCs" is executed. This must be kept in mind if you must tell customer that no current concern has been found. When the vehicle dynamics control module detects a concern, the air suspension system is disabled for the current ignition cycle. If the condition causing the concern clears up during the current ignition switch cycle, the system will not reactivate. For example, if the customer has severely overloaded the luggage compartment, the system will not be able to trim the vehicle without exceeding the compressor run time. This will generate a DTC that disables the computer controlled suspension system. If the customer then drives the vehicle and unloads the luggage compartment without turning the ignition switch OFF, the system will not adjust for the new load. The customer will experience poor ride quality and the vehicle will not adjust trim.

May 20, 2009 | 1996 Lincoln Continental

1 Answer

99 expedition air suspension compressor runs every couple minutes


It is normal for some cycling of the compressor as the ride heights change and the compressor vents and fills air springs. Info:

Air Compressor
The air compressor:
  • Is not interchangeable with the rear air suspension (RAS) air compressor.
  • Consists of the compressor and vent solenoid; neither are replaceable as individual items.
  • Is a single cylinder electric motor driven unit that provides pressurized air as required.
  • Is powered by a solid state relay, which is controlled by the air suspension control module.
  • Passes pressurized air through the compressor air drier that contains silica gel (a drying agent). Moisture is then removed from the compressor air drier when vented air passes out of the system during vent operation.
  • The drier may be replaced separately.
  • The drier has dual ports and is not interchangeable with the RAS drier.
The vent solenoid:
  • Allows air to escape from the system during venting actions.
  • Is part of the air compressor cylinder head.
  • Shares a common electrical connector with the air compressor motor.
  • Is enclosed in the cylinder head casting, which forms an integral valve housing that allows the valve tip to enter the pressurized side of the system.
  • Has an O-ring seal that prevents air leakage past the valve tip.
  • Opens when the air suspension control module determines lowering is required.
  • Provides an escape route for pressurized air when system pressures exceed safe operating levels.
  • Has a 1792 kPa (260 psi) internal relief valve.
  • Is installed with the air compressor as a unit.
Compressor Relay
A solid state relay is used in the air suspension system for compressor control. The relay incorporates a custom power metal oxide semi-conductor field effect transistor (MOSFET) and ceramic hybrid circuitry. The relay switches high current loads in response to low power signals and is controlled by the logic of the air suspension control module.
The compressor solid state relay is energized by the air suspension control module to have high current flow from the battery to the compressor motor.
Control Module
NOTE: The 4WAS control module is also used for the RAS system. The internal processor recognizes external circuitry to determine if it is installed in a 4WAS or a RAS system.
NOTE: The air suspension control module is calibrated with information from the air suspension height sensors. A new or swapped air suspension control module requires the ride height adjustment calibration process to be performed.
A microcontroller-based electronic air suspension control module controls the air compressor motor (through a solid state relay) and all system solenoids. The air suspension control module also provides power to front and rear height sensors. The air suspension control module controls vehicle height adjustments by monitoring the two height sensors, vehicle speed, a steering sensor, acceleration input, the door ajar signal, transfer case signals and the brake pedal position (BPP) switch. The air suspension control module also conducts all fail-safe and diagnostic strategies and contains self-test and communication software for testing the vehicle and related components.
The air suspension control module is interchangeable between the RAS and 4WAS system.
The air suspension control module monitors and controls the system through a 32-pin two-way connector. The air suspension control module is keyed so that it cannot be plugged into an incorrect harness. There are two sides of the harness connection to the air suspension control module. Each is uniquely colored and keyed to prevent reversing the connections.

Pressure Relief Valve
The pressure relief valve (PRV) protects the rear air suspension components by venting the system to a specific pressure in the case of a system malfunction. The system will decrease the pressure to an acceptable level to maintain vehicle height. In the normal operation mode with normal system pressure, the PRV is constantly closed and does not have any effect on the system performance or function. The PRV is replaceable without any air lines.
  1. If the concern remains after the inspection, use New Generation STAR (NGS) Tester connected to the data link connector (DLC) to retrieve continuous diagnostic trouble codes (DTCs) and to execute On-Demand Self-Test diagnostics for the air suspension control module.
    • If the On-Demand Self-Test is passed and no DTCs are retrieved, go to the Symptom Chart to continue diagnostics.
    • If DTCs are retrieved, go to Air Suspension Control Module Diagnostic Trouble Code (DTC) Index in this section.
    • If the air suspension control module cannot be accessed by NGS Tester, go to Pinpoint Test A.
Self-Test
Verify that the following conditions are met before running the On-Demand Self-Test.
  • All doors, liftgate, and liftgate glass must be closed.
  • The transmission is in PARK.
  • The BPP switch is not pressed during the test and the parking brake is not set.
  • The accelerator pedal is not pressed during the test.
  • The vehicle is not in 4L mode.
  1. Fulfill the pre-conditions.
  1. Install a battery charger for the On-Demand Self-Test to prevent battery drain.
  1. Run the air suspension On-Demand Self-Test.
  1. Record all listed DTCs.
  1. Retrieve stored DTCs.
  1. Troubleshoot any On-Demand Self-Test DTCs first.
  1. Retest and clear DTCs after repairs.

Apr 13, 2009 | 2000 Ford Expedition

1 Answer

1989 lincoln air suspension up and quit. nothing.


Try swapping out the compressor relay. On the firewall between the MAP sensor and wiper motor there are two relays. The inner relay is the compressor relay.

Mar 30, 2009 | 1989 Lincoln Mark VII

1 Answer

'98 Chevy Venture Air compressor quit working


i found one fuse under the hood its top left corner small one that is a 30a

Mar 12, 2009 | 1998 Chevrolet Venture Cargo

1 Answer

Owners manual ?


"looking 4 da relay"
there is a solid state relay for the air suspension system , it is next to or near the air suspension pump located at right front of engine compartment ( relay has a 4 wire connector , colors grey/red , light blue/pink , light green/red , and a dark blue/yellow , also behide the right interior kick panel is a fuse area , 3 fuses are involved with this circuit , fuse #111 - a 50 amp fuse , fuse #27 a 5 amp fuse , and fuse #20 a 30 amp fuse , and don't forget the air suspension service on/off switch . if your not 100% happy with my answer , tell me what i can do to help .

free owners manual ?, best i can say is try ebay , here is several available on ebay.

ebay 03 lincoln navagator owners manuals

J5


Jan 22, 2009 | 2003 Lincoln Navigator

Not finding what you are looking for?
2003 Lincoln Navigator Logo

1,193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...