Question about Mazda MAZDA3

1 Answer

Ball joint always breakdown on front driver side

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 25 Answers

If you buy the low price budget ball joints the will fail after a short time...try spending a little more on the best quality ball joint you can get from the dealer.

please rate this,
Rob...

Posted on Sep 19, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the easiest way to replace the front drivers side lower ball joint on a 1998 Nissan Altima?Or would it just be easier to replace the lower control arm?The ball joint is definetly done-for.


just need to get a ball joint splitter , pronged shaped device that you hammer between the ball joint and control arm ,after stripping down the assembly, little tip, when fitting new ball joint apply slight pressure from below when tightening the nut , this will stop the joint from just spinning , i usually use a scissor jack for this

Jun 03, 2017 | Nissan Cars & Trucks

2 Answers

Creaking groan from front driver side tire


The creaking is coming from either the shock ,ball joint, or a-arm bushings. Have someone with you and one person pushing up and down, the other, safely feeling each component till the vibration can be felt. If it is in fact the ball-joint then as long as it is safe (not loose), then just add grease to it as needed and it should go away.

Jun 08, 2009 | 2000 Ford Ranger SuperCab

1 Answer

How do you remove the drivers upper front control arm and ball joint on the front or steering axle.


its in the FSM,
we posted over 200 times now. the full , no need to guess, read.
same car the grand is . just back seat deals. on commander.

i own one, 2010 , immaculate with leather and 85k miles.

is driver on left side, (they sell RHD cars you know)_
always use left or right. so we dont need to guess, your country.

chapter 2
turn to page. 38
its all there step by step.
If the travel exceeds 0.5 mm (0.020 in.), its bad
page 40 covers arm


click wk
http://www.morris4x4center.com/knowledge-base/index.htm?utm_source=cj#service

Feb 24, 2016 | 2006 Jeep Commander

1 Answer

The driver side front tire wobbles


have u had your car lined up at a aliment shop if not your toe end and camber could be not adjusted right

Feb 11, 2013 | 1997 Mercury Cougar XR7

1 Answer

00 eclipse big clunk on front driver side


Check lower ball joint and tie rod ends on drivers side.Sounds like it could be a worn out ball joint.

Aug 17, 2012 | Mitsubishi Eclipse Cars & Trucks

1 Answer

Hyundia matrix 1.6 is it hard to change a drivers side ball joint ?


It is very difficult and requires special tools and skills, you will also need to have the front end aligned after the part change.

Jan 16, 2012 | Cars & Trucks

1 Answer

Right side front ball joint


IT'S USUALLY BETTER TO REPLACE THE WHOLE LOWER COTROL ARM THAT WILL CONTAIN LOWER BALL JOINT AND TWO OTHER BUSHINGS THAT ALWAYS GO BAD.











TIM

Dec 21, 2010 | 2004 Honda Accord

3 Answers

How many ball joints does a 99 dodge stratus have?


It has two,lower ball joints,one on each side.

Feb 11, 2010 | 1999 Dodge Stratus

1 Answer

Clunking in tire


check ball joints by lifting front end and shake tires. if loose your ball joints are bad. you will hear a clunking sound as you apply brakes during driving. its the play in the ball joint. the dealer wants $600 in labor. $160 in parts at auto zone. get the ball joint press also. good luck.

Jan 27, 2009 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

Front drivers side axle removal


There's not any special tools. You need a socket to fit the nut on the end of the axle and a wrench to take the nut and bolt off the bottom ball joint that slides through the control arm. Take a bar, pry down on lower control arm, pulling ball joint out, then pull the upper part out by hand, away from the car, slide axle out of the bearing assembly. Take a pry bar, put between trans and axle, give it a swift, quick ****. The axle should come out. Remember to always put jack stands under the car and be safe. Phil

Jan 09, 2009 | 2003 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...