Question about 1992 Honda Accord

1 Answer

Code 6 in computer

I have a haynes manual,, code 6 was on the computer,, cts,,bought a new cts installed ,,pulled back up fuse to clear computer memory,,light immediately came back on,,rough start again,,tryed disconnecting battery for 30 seconds still light and rough start,,checked voltage at the plug in ,,10volts ,,manual says it should be 5 volts,,and new sensor checked resistance ,,none ,,checked old sensor ,,no resistance until heated and it was sporatic reading when hot,, kind of at a loss here about where to go with this ,,maybe return wire not sending voltage back to computer or is "new" sensor bad also????????

Posted by on

  • replica68 Sep 18, 2008

    how would a voltage surge damage a resistor? kind of the idea of a resistor is how the computer notates voltage spikes up and down from the cts to set idle speeds and mixture!!!!!!!????

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Honda Master
  • 1,779 Answers

Did you disconnect the neg. battery terminal before changing the sensor? I'm wondering if somehow the new one was damaged by a voltage surge? Can't be of any more help than that! Good luck!

Posted on Sep 18, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a manuaul for a 2003 cts Cadillac


Here's the link to Haynes manuals.
They list one for your vehicle.
http://www.haynes.com/products/productID/849#

Aug 17, 2015 | 2003 Cadillac CTS

3 Answers

Unlock a radio CD player on a Cadillac cts 2006


try this video, not sure if it addresses code entry or not:


May have to get it from Dealer.

Jan 03, 2015 | 2006 Cadillac CTS

1 Answer

How do you install camshaft and lifters in 2003 Cadillac CTS 3.2 Liter V6 Engine?


Consider purchasing warranted rebuilt cylinder heads from "Cylinder Heads International" for $275.00 each with free return shipping of your cores. If you choose to do the work yourself get a library card which will allow you to free online access to Haynes or Chilton's repair manuals. Or for $27.00 get a one year subscription to "All Data" which has expanded information. Any of the above will have the timing spec's. Don't make the mistake I made trying to do it without borrowing or buying the tool for that purpose.

Oct 15, 2014 | 2003 Cadillac CTS

1 Answer

My new engine of 70k. Says engine power down at Around 70 75. Or at a red light and I gun it. Usually have to ease to start. Got a new engine the old one had 197k on it. Got both cat converters fixed. May...


computer may not be compatable with new engine-mte needit reprogramed----but cud need throttle cleanin or tuneup--a haynes manual shows details--vacuum leaks are possible creating lean condition--scan car or send issue to magicmechanic online

May 01, 2012 | 2006 Cadillac CTS

3 Answers

Whichnis number one cylinder on a 2004 Cadillac CTS with a 3.6 engine?


2004 Cadillac CTS 3.6L SFI DOHC 6cyl
Firing order 1-2-3-4-5-6 ------- front ' 1 3 5 ' of ' ' vehicle ' 2 4 6 ' ------- distributorless ignition


2004 Cadillac CTS 2.8L SFI DOHC 6cyl
Firing order 1-2-3-4-5-6 ------- front ' 1 3 5 ' of ' ' vehicle ' 2 4 6 ' ------- distributorless ignition


Hope this help (remember rated this free answer).

Jun 03, 2011 | 2004 Cadillac CTS

1 Answer

I have a 2005 CTS cadallic And I cannot open the trunk with my remote or my button oin the drivers side door panel. What do I need to do?


Open the trunk manually. Pull down the back seat armrest and open the door for trunk access. There is a yellow handle that is above the door, pull the handle and the trunk will open manually.
The remedy for your problem is probably the fuse that runs the solenoid to the trunk opener, it is found under the rear seat passenger side. It has a black cover over it, remove the cover and find the corresponding fuse.

Aug 01, 2010 | 2005 Cadillac CTS

1 Answer

Radiator fan won't shut off


Go into fuse box and pull out cooling fan relay this will stop fan.
Then check coolant temperature sensor(CTS) for resistance. You gonna need shop manual for this.
If sensor doesn't match up with resistance spec's replace. If it matches with specs then the only two items left are the relay you pulled and the wiring in the circuit. Test relay for shorts. Back probe wiring for shorts also. Good luck Its usually the relay. But I have replaced CTS's also.

May 07, 2010 | 2005 Honda Accord

1 Answer

Both brake lights are Out


your fuse panel will tell you the location of your brake lights. Haynes manual has much info than the owners manual rob1911.a1

Mar 15, 2010 | 2005 Cadillac CTS

1 Answer

I just bought another factory radio/CD player for my 2005 Cadillac CTS. The installed cd player is inop. When I installed the new unit, I get "Theftlock" on the screen. How dod I reset the radio?


Hopefully you got the unlock code with it, otherwise, write down serial number and model number off back or side of deck, and give dealer a call, they should be able to give you the code .

Feb 20, 2010 | 2005 Cadillac CTS

1 Answer

Theft detorrent system


Go to your fuse box and pull out the fuse to the ECM, that will release the keys from the ignition. You may still have the problem so you may have to reset the whole system by locking the car completely and then putting the ECM fuse back in. Once the fuse is back in, unlock it and that should bring the system back to it's base. If there is a problem with the engine not starting you may have to do the ignition key relearn also and that's about a 30 min program. 
30-Minute Learn Procedure 1. Turn ON the ignition, with the engine OFF. 2. Attempt to start the engine, then release the key to ON; the vehicle will not start. 3. Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF. 4. Turn OFF the ignition switch, and wait 5 seconds. 5. Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 6. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password. 7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles. Without a scan tool you may have momentary starter interruptions while history clears itself. Good luck and hope this helps, keep me posted, be glad to help.

Jul 17, 2009 | 2005 Cadillac CTS

Not finding what you are looking for?
1992 Honda Accord Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6864 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...