Question about 1987 Ford Thunderbird

1 Answer

Boggin when i replaced the valve cover gasket the car started to bogg down under acceleration but only when i drive it

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Check all the vaccume lines .map sensor ?

Posted on Mar 04, 2009


Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is causing hesitation?


Have you ever changed the fuel filter?

Dec 18, 2015 | 2002 Chevrolet Malibu

1 Answer

Valve cover gasket


If the valve cover is leaking oil onto the spark plugs and wires, then yes, replace the gaskets. Otherwise you have other ignition issues.

Feb 18, 2015 | 2004 Chrysler PT Cruiser

1 Answer

1993 festiva replaced the throttle body gasket now will not accelerate at temp


I have a 1997 ford E 150 customize mark 3 van have driven back and forth to work 5 years ran great Christmas Day drove down to the garage and back up to house and now it will not start turns over has spark will not fire

Jan 07, 2014 | 1993 Ford Festiva

1 Answer

95 chevy 1500 pops and backfires doesn't want to shift into overdrive when cold when it does the truck runs real rough


Have you checked the fuel pressure under a load, low pressure will cause these symptoms. The test port is on the top of the engine in the fuel supply rail to the fuel injectors, the fuel pressure test port looks like a large tire fill valve. You will need a fuel pressure test gauge to do this test (about $20), the pressure must be watched while you accelerate, it should never go down on hard acceleration just up about 6-8 PSI

Mar 14, 2012 | 1995 Chevrolet K1500

1 Answer

Changing pvc valve


1995 Geo Truck Tracker 4WD 1.6L TBI SOHC 4cyl
The PCV Valve is located under hood, center, upper engine area, top of engine, mounted in passenger side of intake manifold.

The low gas mileage and the versatility that your 1995 through 1999 Geo Tracker offers are two benefits of owning it. The maintenance needs to be kept up on your Geo Tracker. One form of this maintenance is to replace the valve cover gasket once you have driven 100,000 miles or more.
  1. Allow your engine to cool. Disconnect the negative battery cable. Remove the air inlet hose and air intake case or air cleaner housing. Detach the PCV valve hose from the PCV valve. Separate and remove the spark plug wires and the accelerator cable from their clips.
  2. Loosen and remove the valve cover bolts. Lift the cover up and off. Using a flathead screwdriver, gently nudge the gasket out of the gasket seating area. Using automotive engine cleaner and a clean cloth rag, clean the gasket seating area.
  3. Place the new gasket in the gasket seating area. Put the cover back into place. Put the bolts in and then using a torque wrench tighten them. Do not over tighten the bolts or the gasket will not fit correctly. Reconnect the spark plug wires and the accelerator cable in the holding clips.
  4. Reconnect the rubber hose to the PCV valve. Install the air intake case, or air cleaner housing, and the air inlet hose. Reconnect the negative battery cable. Add oil to the car and start the engine. Allow the car to run 10 to 15 minutes. This will allow the oil to lubricate the engine while it moves to the top.
I hope helps with this (remember rated this help) Good luck.

Dec 29, 2009 | 1995 Geo Tracker

1 Answer

1988 cutlass ciera boggs down when i accelerate


Hello! You have symptoms that point to incorrect fuel pressure.
First have the fuel pressure tested as follows; #1...engine running at idle: 13- 20 psi. #2...key on engine off: 23-30 psi. If pressure is incorrect change the fuel pump.

Does the engine "surge" at idle? If so, check the "fuel injection pressure regulator idle air control valve". Apply a vacuum to it; If fuel flows it is not the problem.


Guru.............saailer


Dec 13, 2009 | 1988 Oldsmobile Cutlass Ciera

1 Answer

93 chevrolet truck bogging down on acceleration


Check intake gaskets. Pour warm soapy water on the gasket when it's running. If it bubbles like crazy, you have a leak. 2. Check timing. Shoot a timing light at the crank mark. If it jumps around a lot, your chain has jumped. #3. check cam. Remove valve covers, run the engine, and see if they are all raisng the valves the same. Put a piece of cardboard along the bottom, and fold it around a little, so it forms kind of a " half valve cover". That way you won't lose oil everywhere, and make a mess, or a fire.

Aug 27, 2009 | 2002 Buick Century

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...