Question about 2002 Isuzu Axiom

1 Answer

Changing the blinker light

I can't seem to get the lense cover off to change the bulb?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 962 Answers

You probably don't have to remove the lense. You remove the bulb from the inside of the engine compartment or trunk. you remove a plug by turning it counterclockwise and pressing in at the same time.the plug comes off with the lightbulb in it.

Posted on Nov 18, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I change rear blinker light

open glove box, extract operators guide.
see lighting page. read that , it covers this simple service.
lost it get one , dont be helpless or stranded.

Sep 21, 2014 | 2011 Jeep Patriot Latitude

1 Answer

How to change front blinker bulbs

the screws are located between the lenses to remove blinkers then you can get to the bulbs

Jan 30, 2013 | 1993 Jeep Grand Cherokee

1 Answer

My blinker lights stop blinking and the fuse box doesn't have a cover to show which fuse is which so i do not no which fuse is for the blinker lights.

change the bulb sometimes one of the filaments where out they are combo bulbs usually 1157 1156 bulbs back stop and tail combo bulbs, or check owners manual, this is depending on your type of vehicle but thats probably it.

Jul 07, 2010 | Cars & Trucks

1 Answer

My signal light wont blink but it comes on, how do i change it or where to start to fix the problem

My first thought: burned out bulb.
With the car in "run" position(doesnt need to be running) and parked, switch on the blinker and get out and look to see which light is on, and which is not.
If somehow both blinker lights come on, then your issue is with a burned out blinker relay which is typically found up, under, the dash. These things are about 1-1/4 inches in diameter and about a 1-1/4 inches tall and will usually be found in or near the fuse panels.

If it's a bulb thats fried....
front end - check under the hood to see if blinker bulbs are accessible from there. If not from inside, you'll hafta remove the light covers/housings from the outside, usually requiring a philips or torx screwdriver of some sort.
back end - these are likely accessible from the trunk, and hidden behind the carpeting, or something, that covers the rear light areas. If not directly accessible, then you'll hafta determine how to remove the bulb covers/housing to get at the dead bulb.

Jan 09, 2010 | 1990 Pontiac Grand Am

1 Answer

2000 beetle, blinkers are not blinking

Do the basic, so this way you can eliminate the relay making sure is good and working. change the turn single relay it fairly cheap to replace. next if that don't work, you going to have to wait when the problems occur again by going around by removing the lense cover one at a time; wiggle thee bulb around or remove it from the socket and put it back in one at a time to see which one is not having a good ground; check and see from your if it blink from your adjustment. you will have to check all the turn single bulbs one at a time by going around the car to each bulbs.

Oct 08, 2009 | 2000 Volkswagen Beetle

1 Answer

Changing out Front Blinker bulb

I didn't realize how simple it was:

take out the ONE screw in the blinker cover.
pull it from the connector.
twist out the black cover around the bulb.
twist out the bulb.
replace with new bulb and i think the rest is pretty obvious!

May 11, 2009 | 2002 Mitsubishi Eclipse

1 Answer

Rear blinker does not work need to access bulb

Your rear bulb is burnt out if you say the front one is working .. the speed up of flashing means your bulb is bad.. you might have to get in the trunk and unscrrew those hand wing nuts and push that tail light outward to get to the bulbs ... thanks Jerry and holler if you need more.

Apr 21, 2009 | Chevrolet Impala Cars & Trucks

1 Answer

99 firebird light problem

check your wiring harness to breaks and shorts also check to see if water is getting into the turn signal lense through a crack

Feb 28, 2009 | 1999 Pontiac Firebird

2 Answers

2001 chevolet cavilier brake lights & blinkers burning up

sounds like you put a 21 watt bulb in place of a 6 watt bulb ,or you have put single pole bulb in place of a double filament,double pole bulb

Feb 02, 2009 | 2001 Chevrolet Cavalier

2 Answers

Rear blinker light change 2001 ram1500

Welcome to FY
open the tale gate look at the side where the light is there is 2 screw that hold the light to the box

Jan 10, 2009 | 2001 Dodge Ram 1500 Truck 2WD

Not finding what you are looking for?
2002 Isuzu Axiom Logo

Related Topics:

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides