Question about 1998 Volkswagen Golf

1 Answer

Failed emissions high co on Nissan Maxima

Our Maxima failed the CO% at idle (3,56) results but passed in cruise (0.07) What could be the problem?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 272 Answers

You could have a dirty air filter, if so change it. Check that your oil is just below maximum ( I normally have the oil just above 3/4 on the dip stick). Also you could add Stop Smoke to your oil to help cut down on the CO's. Also clean out all your breather pipes.

Posted on Nov 28, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Emissions failure 1986 nissan 300zx


MAP sensor needs cleaning or is bad ?

Jul 12, 2013 | Cars & Trucks

1 Answer

C15001993 truck 4.3 v6 Failed Emissions HIGH CO again


Sounds like you lost O2 Control

Check fuel trim & data with professional
scanner & such

You done as far as working at home, you did all
you can

You have a rich condition (CO)

Seems as though the coolant sensor is not working &
your in open loop

Mar 05, 2013 | Chevrolet C1500 Cars & Trucks

1 Answer

1986 NISSAN 300ZX FAILED EMISSIONS HIGH CO


I would replace CATalitic converter, this car is old, plus a tuneup is 100% necessary , spark plugs wires, ditributor cap & rotor, plus both the air & fuel filters need replaced. change oil & filter. then you will pass emissions test. and your car will run like its suppose too. if you don't do all this , then buy a new car !

Feb 02, 2013 | 1986 Nissan 300ZX

2 Answers

Golf 1.4 2003 very high emissions


Replace your oxygen sensors.
murf427

Aug 29, 2012 | 2003 Volkswagen Golf

2 Answers

What does No ppm mean?failed e-test


Here is some info for you to read, besides me explaining what ppm is, i also gave you some info of how to solve this, Ain't that special LOL. Mike

Overall Result: PASS or FAIL. A vehicle with a properly operating engine and catalytic converter will have very low HC and CO readings. However as a vehicle ages the HC and CO emissions will increase and may become erratic. As a vehicle ages it becomes increasingly important to be sure that the engine and converter are fully warmed up before the test to have the best chance of passing the test.

HC (PPM): The parts per million of hydrocarbons (unburned or partially burnt gasoline) in the exhaust.

CO (%): The percentage of the exhaust that is carbon monoxide (CO).

CO +CO2 (%): Complete combustion in the engine or catalytic converter will result in very little carbon monoxide (CO) and a high percentage (up to about 16%) of carbon dioxide (CO2) in the exhaust.

O2 (%): When there is complete combustion in the engine or catalytic converter there is a very little oxygen (O2) in the exhaust. Usually less than one percent. A higher reading indicates a problem with the engine, the exhaust system, the sampling system or the catalytic converter. Vehicles do not pass or fail because of the O2 reading; it is only diagnostic information.

RPM: The engine speed in revolutions per minute (RPM) or N/A.

Cruise Limit: The maximum allowable HC and CO emissions at 2500 rpm. The CO+CO2 (%) must equal or exceed 6. This verifies an adequate sample of the exhaust has been obtained. N/A for O2 and RPM.

Cruise Emissions: The emission readings measured at 2500 rpm.

Cruise Result: PASS, FAIL or N/A.

Idle Limit: The maximum allowable HC or CO emissions at idle. The CO+ CO2 (%) must equal or exceed 6. This verifies an adequate sample of the exhaust has been obtained. N/A for O2 and RPM.



These are the possible problems:

bad o2 sensor
bad EGR valve
bad cat
bad timing
dirty injectors
bad plugs or wires
the less costly fixes include replacement of the o2 sensor and EGR valve i would not clean the EGR I would buy a new one there are very cheap you can pick these up at any local parts store .
also run some injector cleaner through your car at least a full tank of gas and one bottle of injector cleaner should be ran through.
you can also have your timing checked for a relatively low price.
and when you go into to have the vehicle checked make sure the car is been running because your cat convertor has to be warm in order to preform at it peak so do not do it when the car is cold.
all of the above are pretty reasonable fixes the general rule of thumb when you work on your own vehicle is start with the cheapest fix first then go on to the next.

Aug 11, 2011 | 2000 Saturn Ls 4dr Sedan

1 Answer

1987 nissan 300zx failed emmissions too much co I


change oil and filter put a emission cleaner in fuel

Jul 11, 2009 | 1989 Nissan 300ZX

3 Answers

Failed emissions test


Hi Don,

First, thank you for asking me for my input on this. It just so happens, that I used to own a Ford ranger that had the same engine as yours. It was a 1990, but there are few changes to these model years.

Anyway, there is only one reason that your HC levels would be high. Your engine has WAY too much unburned fuel in the exhaust. The same reason applies to high CO levels. Too much fuel and/or not enough air.

Below is a link that you may find very helpful. It explains exactly what we are talking about here and also lists some of the possible causes.

EMISSIONS ANALYSIS

Incidently, when I had the same emissions failure on my truck, replacing the air filter and replacing a failed MAP sensor fixed it. - I did NOT have to replace the catalytic converter. If the numbers are as high as you listed above, you will only destroy a new converter anyway because there is obviously not enough oxygen in your exhaust system for the catalyst to function properly. Those numbers are nearly DOUBLE the allowable maximum. If the engine is running correctly and the catalyst is good, your numbers will be WAY BELOW those maximum numbers.

Please understand that I am NOT telling you to replace your MAP sensor without proper diagnosis. There are many possible causes here. Please click the link above and read the article. It will help you to understand what is going on here.

Jun 03, 2009 | 1989 Ford Ranger

2 Answers

Ford failed MOT on High CO emission


High CO usualy means the O2 sensors are not reading properly. Take it to a parts store that can read codes, I know Auto Zone does in my area. If it is the O2 sensor it is an easy fix but the sensors run about $50.00 each.

Apr 18, 2009 | 1995 Ford Escort

Not finding what you are looking for?
1998 Volkswagen Golf Logo

Related Topics:

304 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

yadayada
yadayada

Level 3 Expert

70387 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...