Question about 1997 Toyota Camry

1 Answer

1997 camry slides when turning

I have a camry and the axle was replaced this year but when i turn slightly (like going around a curve) my car slides like its out of control. I almost loose steering for a brief moment.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 1,861 Answers

My experience with this type of issue is as floows:

You may have a broken coil spring or strut.
You may have excessively worn lower control arm(s).
You may have broken sway bar links.

In any case, this needs to be looked at ASAP.

Hope this helps.

Posted on Sep 17, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1987 Toyota Camry having trouble replacing axle because the splines are offset and the axle won't go back in can u help me troubleshoot


I had a problem replacing the axles on my 88 Accord once because the splines and end of the shaft had been painted. I had to sand it down to get the axle to slide in. You also have to turn it until the splines line up in the grooves to slide in. Shouldn't take a lot of force.

Jul 31, 2014 | Cars & Trucks

1 Answer

Left new axle doesn't want to slide in on 97 toyota avalon v6


i had the same problem on a toyota camry. what worked from me is i went out and bought a pair of i piping vise grips from northern tool, they look like a whales mouth. anyways they are big enough to wrap around the axle. lube the axle spine with grease then put a piece of pipe against the vise grip. and knock the **** out of it with a hammer.

trust me i know this sounds bad but it works

Apr 14, 2011 | 1997 Toyota Avalon

1 Answer

Hi I'm replaceing the axle shaft on pass front on 96 camry And the bugger just won't slide into transaxle.Any ideas ?


use a slight twisting motion as you lift up on the entire axle sometimes the seating position can be up little higher than you might think if you lay the new and old axles next to each other and they appear to be the same size around and the same length it should go with little effort hope this helps

Dec 22, 2010 | 1996 Toyota Camry

1 Answer

Feel shake in the floor and steering wheel at around 70 mph and a slight turn on the steering wheel you can feel it a little more. what parts could cause this? already had the wheel balances checked.


Tierod ends. Bad belt in a tire. If you have a bumpy brake pedal, a warped rotor has enougn play to bounce against pads. Also Hub bearings were known to fail after 35,000 miles.

For Hub bearings there may be a Service Bulletin, but your vehicle is going on 10 years old. Usually the side that shakes the most on a opposite curve is the problem side. As in left curve the outside right tire is spinning slightly faster, right side curve its the left side spinning faster.

May 26, 2010 | 2001 Mercury Mountaineer

1 Answer

Change rear whell seal 1997 f-150 gear oil comeing out of rear whell took tire off; took drum off; and saw gear oil all over brake shoes. Seal or bearing need to be replace? how?


replace the axle seal to replace pull the rear cover draining the gear oil then rotate the carrier around till the small bolt holding the carrier pin remove bolt pull pin out don"t turn carrier after pulling the pin push the axle in and remove the clip from the inside of the carrier that pin holds the axle clips in place after pulling out you can remove the axle then just pop the seal out and install new one use a socket or something that is the same size as the seal lube the axle and slide axle back in lift up when almost all the way in the tube putting it in the carrier once in replace clip and pullout on the axle thats it pretty much hope this helps you out

Mar 24, 2010 | 1991 Ford F250

1 Answer

Does my 1997 toyota camry ce 4 cylnder have abs im changing my front axel


ABS was optional on the 97 Camry CE - some have it, some don't. If your car is equipped with ABS, you should have an ABS indicator light on the dashboard, that goes on when you first turn the key in the ignition. But if you are not able to determine whether your car has ABS, it's not a problem. The axles compatible with ABS will also work if your Camry does not have ABS. They cost about the same as axles without ABS. So if you are not sure, just buy the axles for ABS.

Mar 09, 2010 | 1997 Toyota Camry

1 Answer

1996 Jeep Grand Cherokee Laredo 4X4 4.0L. Just recently bought and there's a popping noise in the front and when turning sharply it's like the wheels lock and the jeep refuses to move and it's also...


sounds like a bad cv joint in one (or both) of the front axles. is the popping sound more prevalent when in reverse, with the wheel turned? if so, i'd assume that it is a bad cv joint and one or both front axles will need to be replaced.

Feb 05, 2010 | 1996 Jeep Grand Cherokee

2 Answers

EXHUST BANGING WHEN I GO OVER BUMPS AT REAR


is the car full of people if yes check exhaust clamp is not pointing towards floor or axle if so turn clamp around that should fix it.

Sep 25, 2009 | 1997 Ford Escort

1 Answer

Unable to pull out rear axle to change brearing


remove differential cover,turn axle until chunk turns around to access the small 5/16pin bolt remove pin bolt ,slide spider gear axle rod out ,go to axle ur working on and push axle inward ,ther is a c shaped key on end of axle where u took spider axle rod out remove this key easly by hand and pull axle out,,,note do not turn chunk after removing spider axle rod or ur spiders will fall out

Jun 28, 2009 | 1996 Chevrolet Blazer

Not finding what you are looking for?
1997 Toyota Camry Logo

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...