Question about 2000 Honda Accord

1 Answer

Hood struts How do you replace hood struts on a 2000 honda accord?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 421 Answers

There is a little c-shaped clip on the top and bottom sockets of the strut where they attach on the hood and fender , support the hood with a stick, and pry these two clips back while pulling the strut off the ball studs, you do not need to remove the clips all they way, then the new ones just push on to the ball studs, good luck and please rate -jeff

Posted on Sep 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 Honda accord difficult to turn the wheel


if the noise happens when the car is moving then you're hitting theh wheel stop that prevent the wheel from rotating around. typically the wheel stop looks like the back of a cupped hand and its located on the lower control arm that comes off the strut. smear some grease on it and that will probably eliminate the noise.

on some cars the noise is from the strut bearing on top. the strut bearing is located on the top of the strut tower. You can hear that noise if you stand on the side of the car with the hood open and then have someone turn the wheel until the noise comes in. the car doesn't need to be moving to hear a bad strut bearing.

lastly, check the belt tension for the power steering belt as the belt may be slipping under the load of a full turn

Nov 02, 2011 | 1997 Honda Accord

2 Answers

The hood want stay up, it was repaced but still want stay open.


Did you replace hood struts or entire hood? Sounds like hood struts need replaced.

Jun 19, 2010 | 1994 Dodge Intrepid

1 Answer

How to cange front shocks.?


Raise and support the car safely and remove the front wheels. Undo the clip holding the brake line to the strut. Loosen the bolts holding the strut to the steering knuckle. Before removing them, remove the strut mount tower bolts under the hood. Then remove the other bolts, the entire strut assembly will slide out. You can either install a complete new strut and spring assembly (more expensive), or you can use a coil spring compressor to remove the spring from the old strut and install it on a new strut (less expensive but a lot more work, and you must have access to a spring compressor). Make sure when installing the spring that it is aligned correctly on the new strut. Also, you should replace the strut mounts with new ones. Be aware that a compressed spring is very dangerous, so be sure to follow the instructions for the spring compressor. Re-install the strut assembly. Make sure that the knuckle bolts and strut mount bolts are torqued to spec.

Mar 28, 2010 | 1990 Honda Accord

1 Answer

ENGINE LITE... WHERES THE READER PLUG... 1995 Honda Accord V6... made in Maryville, OH


in 1995 it was optional for car makers to use either OBDl or OBDll computer systems, if yours is OBDl it's under the hood, 14 pin connector on one of the strut mounting nuts, if OBDll pull out your ashtray and it will be there

Dec 09, 2009 | 1995 Honda Accord

3 Answers

Where is the fuel filter of 1998 honda accord v6? please show pic


456dfc9.jpg
The outlet line of on a Honda firewall-mounted fuel filter uses a banjo bolt type fitting. Always use new sealing washers when reinstalling the banjo bolt

Oct 10, 2009 | 1998 Honda Accord

3 Answers

2000 Honda Prelude hood won't fully shut


Cable is sticking, look at hood latch and push down on the thin cable. It will allow the hood to shut. my 96 Accord does the same thing.

Aug 03, 2009 | 2001 Honda Prelude

1 Answer

How can i change headlights for my honda accord 2000.i want to replace the headlights for my honda accord 2000 car. can i do myself amd how


open the hood and reach behind the lights. There should be a ring, turn this plastic ring until it stops and the bulb should come right out, theres probably a better explanation in your manual

Jun 20, 2009 | 1999 Mitsubishi Mirage

1 Answer

Engine code for 04 Honda Accord p2138, What is it and were is it!!!!!


P2138 is the APP sensor (accelerater pedal postion). More than likely it is the sensor itself that is bad. Clear the code and see if the light comes back on, It may be an intermittent failure. The sensor is located under the hood by the right strut tower.

May 03, 2009 | 2004 Honda Accord

1 Answer

Wiper fluid dosnt spray when hood is down. 1991 honda accord lx


It has to be pinching the tube when you close hood. Replace tube since it is cheap hose and see if it came lose from or is missing a mount to hold the hose.

Sep 30, 2008 | 1991 Honda Accord

Not finding what you are looking for?
2000 Honda Accord Logo

Related Topics:

280 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...