Question about 1994 Buick LeSabre

1 Answer

Ingnition swich how to install the ignition switch

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Buick Master
  • 64,052 Answers

You must disconnect the steering column and drop it down, the ignition switch is on the top of column down low, big multi-wire connector plugged into it.

Posted on Sep 20, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ingnition won't turn past the accessory position


There is a piece of forged metal that is called a rack that attaches to a rod that gies down to the bottom of the column to the Ignition switch these racks have been known to break and jamb up and I have also seen Ignition switches jamb also. Go to the base of the column and remove the switch and see if the key lock cylinder moves all the way now. Then trace your problem to either a jambed Ignition switch or a bad rack and rod.

Jul 26, 2010 | 1989 Chevrolet Camaro

1 Answer

Replace ingnition switch on a 1995 vw passat ?


You must also remove the wiper / turn signal switch cluster. Before you can do this... Most of the 1995 Passats were fitted with a splined cone fitted on the steering columb just under the steering wheel. However a special pullers is needed to remove this cone. With this cone and the trim around the switches removed its a simple enough to remove the ignition switch.
All the best
John

Aug 15, 2009 | 1995 Volkswagen Passat

1 Answer

I installed a new ignition switch in my 1988 mustang


there is a ingnition rod going from key switch to ingnition switch ,it is probly not in the slot any more or the ingnition cam is broken

Jun 28, 2009 | 1988 Ford Mustang

1 Answer

2005 chevrolet impala ignition swich


Even if you bypassed the switch, your steering would remain locked. In order to determine what is wrong with it, (other than the obvious) It will need to be taken apart. You will need a manual (such as Haynes, chilton etc) in order to do this safely and correctly.

Mar 24, 2009 | 2005 Chevrolet Impala

1 Answer

I need instructions on how to put a locksmart switch ingnition


Removal
  1. Disconnect battery ground cable. Remove the steering column shroud by removing the four or five self-tapping screws. Remove tilt lever (if so equipped).
  1. Remove instrument panel lower steering column cover.
  1. Disconnect the ignition switch electrical connector.
  1. Rotate ignition key lock cylinder to the RUN position.
  1. Remove the two screws retaining ignition switch.
  1. Disengage the ignition switch from the actuator.
Installation
  1. Adjust the ignition switch by sliding the carrier to the switch RUN position. NOTE: A new replacement switch assembly will be set in the RUN position as received.
  1. Check to ensure that the ignition key lock cylinder is in the RUN position. The RUN position is achieved by rotating the key lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch into the actuator. It may be necessary to move the switch slightly back and forth to align the switch mounting holes with the column lock housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is locked in the LOCK position.
  1. Install instrument panel lower steering column cover.
  1. Install the steering column trim shrouds and tilt lever (if so equipped).

Feb 26, 2009 | 1991 Lincoln Town Car

1 Answer

97 cavalier was running but just stopped.


Question:
Did you replace the ignition switch or the KEY AND CYLINDER?

These are the only 2 things that can make your engine turn off when you release the ignition switch after starting the engine.

I hope this helps you.
ramonalees.com

Jan 30, 2009 | 1997 Chevrolet Cavalier

1 Answer

1991 honda accord ex headlight problems


Hello, firstly I was wondering if the lights shut off when you pull the switch off the harness?
If YES, then THAT switch or wiring could be bad
if NO, then it's most likely the body control module

Jan 12, 2009 | 1991 Honda Accord

1 Answer

LOW VOLTAGE ON A FEW WIRES WILL NOT RUN


Many wires on most autos will have low voltage around 5 volts is common for wires going to most sensors. What you described with the fuel pump sounds normal for this truck. I would guess the fuel pump is not your problem cant say for shore with out any more info. I am unclear as to what the symptoms are, is the truck not starting. What led you to check the fuel pump. Did you check for spark.

Jan 10, 2009 | 1991 GMC S-15 Jimmy

1 Answer

Starting problem


check your reverse swich. if the switch doesnt see connection, being out of reverse/in reverse, then the ignition switch will not get supply power. look for swiches/sensors by the shifter and ignition swich for possible faulty switch/sensor. hope this helps

Aug 09, 2008 | 1995 Saab 900

Not finding what you are looking for?
1994 Buick LeSabre Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...