Question about 1996 Dodge Caravan

1 Answer

Timing trying to find how the timing lines up

Posted by on

  • zerofreeze33 Oct 03, 2008

    i need to know the timing marks for a 96 caravan 2.4 liter enigne its a pain in the the rear end

  • yadayada
    yadayada May 11, 2010

    What engine do you have?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 512 Answers

The 2.4 is a pain. you need to lay a straight edge across all 4 marks on the cam gears,,,the crank has a notch that lines up with a triangle on the oil pump

Posted on Oct 05, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Timing belt re-install and engine hard stops when rotating by hand even when timing marks lined up.


That hard stop is the valves hitting the head of the piston, you most likely have bent a valve, you have the valve timing wrong.

Sep 25, 2016 | 2006 Chrysler 300 Touring

1 Answer

Cant get breaks on my 2002 blazer ather break lane breaks


After you fix a brake line, you need to bleed the line. There is air in the line that needs to be bleed out of the line. Make sure the vehicle is not running, totally shut off. First - find which tire the brake line goes to that you just fixed. Two - then have someone in the vehicle pumping the brake three times, then on the third time, have them hold the brake to floor. Three - open the bleeder valve on the brake caliper of the tire that the brake line goes to.(Note - You need the tire off the vehicle to do this.) Four - once the the bleeder valve is opened, and all the brake fluid, and air comes out, close the bleeder valve and repeat the whole process several more time. Each time you bleed the brake line you are releasing the air in the line, and creating pressure with just fluid in the line. Usually three to four tries of bleeding the line will solve the air in the brake line problem and your brake pedal will become hard.

Mar 22, 2014 | 2002 Chevrolet Blazer

1 Answer

99 chevy vorte marks wont line up


if you lined up marks on cam and crank gears when you installed timing chain and you used the original timing cover and timing mark tab and did not turn engine before checking the marks the balancer is spun and needs to be replkaced if the engine has been turned it may be 180 degrees out of time you will need to turn engine at least two full revolutions and recheck maybe upto 4 times if it still does not line up with all original parts no chrome timing covers or timing tabs the balancer is bad and needs replaced

Mar 27, 2012 | Chevrolet Tahoe Cars & Trucks

1 Answer

Im trying to get the timing marks aligned and dont know where to align them to. Its my neighbors car and he doesnt have a service manual. Someone else tried replacing the timing belt for him and didnt...


with the timing belt on the vehicle install the botton piece of the timing cover with crank pulley. line up the notch on the crank pulley with 0 on the timing cover for top dead center on the crank. then there is a small sight hole in the spokes on the camshaft timing gear. with the belt off the timing gear line up that sight hole with a notch behind the gear on the cylinder head. you will only be able to see the notch through the sight hole with a mirror. once these are lined up slide the belt back on the timing gear and recheck afterward. this the procedure for all 5s-fe motors

Nov 12, 2009 | 1991 Toyota Celica

1 Answer

HOW TO REPLACE CAM SHAFT SENSOR


Chances are your cam sprocket is off one tooth, bring the engine to Top dead center #1 cylinder firing stroke lining up the flywheel timing pointer notch to the timing marked zero. remove the timing belt cover to check that the timing marks line up if not remove tensioner and reset the sprocket so it lines up then reinstall tensioner recheck.

Sep 11, 2009 | 2002 Volkswagen Passat

1 Answer

Timing belt changed


it doesn't sound like your timing is lined up properly, it sounds like your timing is out. i recommend you check your timing to your cam and crank to ensure they are lined up

Sep 05, 2009 | 2001 Toyota Highlander

1 Answer

I cant get my timing marks to line up.


take it to a shop before you destroy the engine

Jun 02, 2009 | 1995 Eagle Talon

2 Answers

2000 Chevy Silverado Z71 hard to start


Pull the vac line off the regulator right after you stop the engine. See if there is gas in the vac line if so the regulator is bad. If no gas is present it could be the check valve in the fuel pump letting the gas pressure leak down. Get a set of gauges and hook up to the fuel lines and check for pressure loss. You will have some loss but should hold steady for several hours. Another thing to try is turn the key on and off several times before trying to start this will charge the lines if this works every time you are losing fuel pressure. If you still have trouble when doing this I would look somewhere else besides the fuel system

Mar 06, 2009 | 2000 Chevrolet Silverado 1500

1 Answer

Removing fuel filter


it takes a special tool to disconnect these lines. go to your local auto parts store and ask for the fuel line disconnect tool.once you have the tool put it on the fuel filter prong that the fuel line is connected to and slide the tool up into the gas line, at the same time pull the line away from filter. you may half to try this several times.also when the tool slides up into the line twist the line and push in and out. in short thare is a spring up in that line that gets stiff and corroted so moving the line around while the tool is in place helps free up this sprind.also spray a little lubracant in the ends of the lines before beginning.

Jan 14, 2009 | 1998 Ford Expedition

Not finding what you are looking for?
1996 Dodge Caravan Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

64286 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...