Question about 2005 Chevrolet Malibu Maxx

2 Answers

2005 malibu no heat

My 2005 malibu has no heat. When you turn the heat knob from ccw to cw, nothing happens?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

No heat my 2005 chevy malibu.

Posted on Dec 20, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Possibility your nob/resistor in the nob is bad. The resistor changes current in corolation with nob position.

Posted on Jan 23, 2009

3 Suggested Answers

Molson02536
  • 3854 Answers

SOURCE: 2005 malibu - heat/ac has 4 levels for fsn, level

Your blower speed resistor has gone bad and needs to be replaced. You can pick one up at Auto Zone or Parts Source with the step by step instructions to getting the resistor replaced with common tools.

It is located under the glove box, way in the back of the passenger foot area. You'll need to remove 2 screws with a 7mm socket, and remove the plastic cover that covers the blower motor and another component box that I think controls the passenger airbag. After removing the plastic cover you'll need to side that passenger airbag module to the right so it pop off its mounting bracket and move it out of the way. That will give a better view of the blower motor. I highly recommend you also remove the blower motor itself because the Blower Motor Resistor is located behind it. I think you'll need a 5mm or 5.5mm socket to remove the 3 screws that hold in place the blower motor and 2 more screws for the Blower Motor Resistor... It's a cramped location to work in but if you have all the tools and enough lighting then it shouldn't take more than 30-60 minutes to do. The Blower Motor Resistor costs about $19-$25. Good luck

Posted on Nov 30, 2009

  • 60 Answers

SOURCE: my 2005 malibu variable heater/cooling knob will

your connector probably came loose from the back side of the heater control module. try taking it out and checking the linkage.

Posted on Jul 09, 2009

tripletauto
  • 1450 Answers

SOURCE: What direction does the Rad.

the valve turns counter clockwise

Posted on Aug 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking rearward towards front of engine from in front of radiator, which way, CW or CCW, does 87Ford Ranger2.9L crankshaft (fan & pump) turn?


fan clutches are Left hand thread as they tighten up when the engine is running. If they were right hand thread then when the fan is working they would come loose off the shaft
In short undoing then actually tightens them

Jan 11, 2015 | Cars & Trucks

1 Answer

Malibu heating and ac


does the car have automatic climate control?

Apr 05, 2014 | 2005 Chevrolet Malibu

3 Answers

I just want to know where the radiator drain plug is located


Follow the bottom hose to the base of the radiator. If there's no drain petcock there (most newer vehicles don't have one) you'll need to carefully remove that lower hose from the radiator in order to drain it.

May 29, 2011 | 2003 Saturn VUE

1 Answer

2005 grand cherokee. with the wiper arm removed, motor turns clockwise all the time. what causes arm to sweep ccw then cw. rear window


it has linkage you cant see below the windshield kinda similiar to that of an old steam freight train....remember how the wheels went around?? even though the wheels went one direction at the end of that linkage the piece went in/out (back n forth)

Mar 25, 2011 | 2004 Jeep Grand Cherokee

1 Answer

The 4x4 four system will not engage at all. niether one if the 4x4 light come on on the dash and nothing happens when swtich is in four wheel drive. I have checked all fuses and relays that r assocaited...


Operationally vacuum holds the IWE ( Integrated Wheel Ends ) out, and once vacuum is removed the spring engages the IWE.

Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
- If it turns it is a problem with the transfer case.
- If it doesn't it is a front axle engagement problem.

- If the front drive shaft does not turn :
- Shut of the truck ( still jacked up, and supported ) remove the vacuum lines from the IWE. The spring should push the gears in, without the vacuum line on.
-Check the vent line ( tube that is routed into the engine compartment with nothing attached to it ), for blockages.
-If the vent line is clear, and with the vacuum lines off the IWE should be engaged ( both front wheels locked ).
-If they lock, the problem is with the IWE solenoid not shutting off vacuum to the IWEs. There is a TSB on the 2004-2006 IWE solenoids, a newer revision has been made, and used from 2007 and newer MYs.

- If the front drive shaft turns:
-Check the fuses for the 4WD system ( If ESOF system ) . These are #11, #29, #30 and #111. Use a meter to check the fuses while plugged in, there are pins on the back of the fuse for this. Use a known good ground and check each side of the fuse with the other meter probe, with the meter set to V-DC ( check the scale if a setting that it will read at least 13 V DC ).
-With the key on, if the ESOF system have someone turn the mode selector from 2WD to 4WD while hitting the transfer case with a dead blow hammer ( do not use a metal hammer, it can damage the transfer case ). Some times the shift motor will get stuck ( lack of use ? ) and the dead blown hammer will free it up.
-There are 2 relays ( in the small engine compartment fuse / relay panel - ESOF only ) for the 4WD system, one is the CW ( **** Wise ) one is the CCW ( Counter Clock Wise ). These are full size relays, that can be bench tested, or a quick remove and replace test with the high beam relay in the cab fuse panel ( Relays R03 ). 1 at a time, remove the CW & CCW relays and install them in the position for the high beam relay, and test the high beams by pulling back on the MFS ( MultiFunction Switch ). If the high beams work with both relays, the CW & CCW relays are not the issue ).
-Check the connector on the transfer case for the shift motor, to make sure it is not corroded.

There is a TSB for the 04-06 MY trucks, here it is in PDF format
http://my.voyager.net/~sscully/file_tsb06_08_15.pdf

Here is the block diagram for the IWE vacuum system
sscullys_129.jpg

Mar 07, 2011 | 2005 Ford F-150

2 Answers

Trying to get the oil filter cap off of a 2005 Pontiac Grand Am. Am wondering if it is clockwise or counter-clockwise?


It is a right handed thread, meaning lefty-loosey, turn it to the left.Some of them do get hard to turn. Hope this helps.

May 06, 2010 | 2005 Pontiac Grand Am

1 Answer

My 2005 malibu variable heater/cooling knob will not work right. no heat will come out when I move the knob to the "heat" side of things


your connector probably came loose from the back side of the heater control module. try taking it out and checking the linkage.

Jul 09, 2009 | 2005 Chevrolet Malibu

2 Answers

Heater


Try spinning the knob real fast in either direction. Sounds stupid but it worked for me.

Sep 27, 2008 | 2005 Chevrolet Malibu

2 Answers

No heat


THE AIRDUCT EXCHANGE FUNCTION IS NOT WORKING , IT MAYBE THE CONTROL SWITCH ITSELF .WHAT TYPE OF VEHICLE IS IT

Aug 12, 2008 | 2005 Chevrolet Malibu

1 Answer

What is the torq for the front wheel bearing on a 2002 f150 2wd


As odd as this is, this is how the Ford Manual specifies the procedure:


1.) While rotating rotor Clock Wise, tighten nut to 40 NM (30 Ft/lbs).

2.) While rot. CW, loosen 2 turns.

3.) While rot. CCW, tighten to 23-40 NM (17-24 Ft/lbs).

4.) While rot. CW, loosen 1/2 turn.

5.) While rot. CW, tighten to 2 Nm (17 INCH/lbs, NOT foot/lbs!).

6.) Install nut retainer & cotter pin.

Jul 27, 2008 | Ford F-150 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,397 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...