Question about 1988 Mazda B2200

2 Answers

Doing u joints on a b2200 and it will be mine frist time on one

A friend told be that mazda b2200 u joints cant be taken out is that true.
he said i have to buy a new drive line.
i have done u joints on a chevy it will kind of be the same right

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Can i have a diagram on how to change a universal joint for a 91 mazda b2200

Posted on Aug 27, 2011

They sell a ujoint kit for the two ujoints that aren't replacable the front one and the rear one the center joint is replacable. the front and rear are staked in and you have to grind the little tabs out, then you can press the old joints out and replace them with the new joints that accept a snap ring just like the center joint. I have just done this on my 91 b2200 so i know it can be done. the parts store should have number for the joints just tell them you have the staked in u-joints

Posted on Sep 27, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove the steering wheel on a 1989 mazda b2200


Remove drivers knee panel then electrical plugs to steering column. Nest inside the engine bay remove the bolts from the universal joint. Last remove the two bolts holding the steering column to the dash frame.

Feb 14, 2015 | 1988 Mazda B2200

1 Answer

How do i lower the spare tire on 1989 Mazda b2200 pickup?


will need the original wheel tools is about 4 foot long with hook on one end and square solid tool joint on the other which takes the handle supplied. go to the rear of the vehicle and insert the tool into the slot on top of the spare wheel and wind anti clockwise until the wheel is onthe ground

Jul 27, 2010 | 1988 Mazda B2200

1 Answer

2005 Freestar -The odometer / info center light intermittently goes out. is there a bulb? Or I have read about bad solder joints on the circut boards of F150's.


you are spot this model suffered from faulty circuit boards ie solder joints,a friend of mine suffered the same problem.He told me he was sitting in traffic one night and was so annoyed with the problem he smacked the dash with frustion .it never happend again ,true story.

Jul 02, 2010 | 2005 Ford Freestar

2 Answers

1989 mazda b2200 can not set timing


i have a 1988 mazda b2200 and i was sittin still runnin and it was a lil low in water and i was just ab to take off when it cut off. it made steam *** out the hood. the thing is its gettin eletric to the plugs and its gettin gas and i even tried a lil eather and its turnin over it just want crank. do u have a idea wat it could b? im thinkin it jump timeing.

Feb 17, 2010 | 1988 Mazda B2200

2 Answers

1989 mazda b2200 ujoints will not seperate from the rear driveshaft. the repair manual says there are supposed be c-clips holding the ujoints in and I cant see them. Anyone run into this problem?


yes i have they are realy hard to see you have to get the cv joints realy clean inside to be able to see them, thy are not where you would think they are, where the bearings are you have a shell like thing where they sit, where the shaft goes into it the c clips is about 1/4" inside you have to use two screw drivers flat end type and prize them appart, best way is to clamp the shaft and when you get the c clip far enough appart the cv joint just falls off...hope this helps

Feb 15, 2010 | 1988 Mazda B2200

1 Answer

I have a 1989 mazda truck 4clyin. 5 speed and the engine ten's to dog down alot when climbing a hill in 1st and 2nd gear i need some way of restoring engine power? the clutch is fine the but i need some...


most of the time that is the clutch causing it to do that. trying going up a hill again in frist and push the gas to the floor if the rpm rev up real high like the truck is in neutral then you need a new clutch. try the engine restore it comes in a sliver can your local auto store will have it. it is about $6 a can. but other than that you might just have to rebuild the motor. hope this helps

Oct 06, 2009 | 1988 Mazda B2200

1 Answer

I WOULD LIKE TO KNOW HOW TO PUT FRONT AND BACK U JOINTS ON MY DRIVE SHAFT ?


Well since it is a mazda it is manfuactored by ford so let me ask is the drive shaft held to your rear differental with four bolts our is their just clips on the outside of u-joint

Jul 12, 2009 | 1988 Mazda B2200

2 Answers

1990 mazda b2200 drive train


Is it standard shift??? if so, look under the truck and see if the drive shaft is turning. It could be the clutch, U-joint, or the rearend gone out.

Jan 31, 2009 | 1988 Mazda B2200

2 Answers

I have 1987 Mazda B2200 2.2 ltre, turns, fires, no fuel psi.


I had something like this before. There is a fuel saftey switch near the gas tank right by the rear end. Its a roll over sensor and mine fell off the mount and I guess the truck thought it was upside down :)

Dec 03, 2008 | 1988 Mazda B2200

1 Answer

Mazda b2200, 1989 109000 miles. Vibration, seems to be in the front end, when moving between 30-40 mph, 3rd or 4th gear. Vibration still exists when not in gear, manual transmition. Tires are new and...


I have the same thing but mine is between 45-50 mph. I read about this a while back in a magazine for people that pull campers, the problem exists in all vehicles although its not as noticeable in every thing you ride in. There is a certain "point" at which your speed and engine speed reach, that causes a phenomonon that causes a vibration. Engineers relate it to "harmonics" which is a similar issue but in the electronic field of study. There is nothing you can do for it, and it varies from unnoticeable in some vehicles to driving you insane in my 1989 Mazda B2200. I had an '89 Ford F-150 that did it at 35 mph and a 2001 Dodge Diesel that did it at 45 mph, but those were the only three vehicles I've ever driven and noticed it.

Jul 17, 2008 | Mazda B2200 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

809 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...