Question about 2004 Ford F350

1 Answer

F-350 no start

we did a scan of our F350 6.0L Diesel and the cam and crankshaft sensor codes came up. we changed both to new still not starting, need some sound advice for next step...

thanks in advance

Posted by on


1 Answer

Check wiring,the early 6.0 had problems with wiring harness chaffing and rubing through.

Posted on Oct 22, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Hi I have a Santa Fe diesel 2.2 2007,it won't start but will start with easy start. code P0336, crank sensor changed and cam sensor. code keeps on coming up got hand held machine to cancel the code.

code p 0336 refers to crankshaft (CKP) sensor --range /performance problem=== causes insecure sensor/rotor--- air gap--- wiring--- CKP sensor
check for gunk under the sensor end or in the gaps of the rotor
check wiring

Jun 17, 2017 | Cars & Trucks

1 Answer

I have a 2000 eclipse 2.4 auto rs. Car just shut off while driving. Scanned the mil and showed a code for the camshaft position sensor. Car owners father replaced the crankshaft position sensor (dunno...

if the code shows a cam position sensor then it is the cam position sensor and not the crank position sensor
get the car to an accredited service center before it cost more money from inexperienced interference

May 28, 2017 | 2000 Mitsubishi Eclipse

1 Answer

08" Ford F-350 diesel no start.

6 0 Powerstroke no start IPR valve tips and tricks P2291 P2290

Watch this guy's videos , send him a message ! for ford diesels he's good !

Dec 06, 2014 | Ford Cars & Trucks

1 Answer

How do I fix my v6 Camry the turning but would run I change coil ,cam and crankshaft sensors still wouldn't start

What was the original problem?

Did you look at Scan Tool Data?

Did you do any testing?
If not--- you found no problem
So why change any parts?

Who changed those parts-- a repair shop

Did you check for OBD Codes & look them up,
to see the possible issues?

OBD Codes have nothing to do with parts replacement

They are used to diagnose the system that set the codes
& then you have to component test to find a problem

Nov 23, 2014 | Cars & Trucks

1 Answer

Can anyone please tell me where the cam sensor and crankshaft sensor are located on a 2002 RAV4 2.0 D4D...116BHP Problem is wont start when engine is hot.

this a diesel. (our is 2.4Lgas(petrol)
cold starts fine,runs perfect cold RIGHT?
common rail system.

the PCM will tell you when those are bad, cranking for 5sec or running.
does your run,. ? if yes for get them. and scan engine PCM.
some sensor takes major work to reach.

get the FSM on that car. y
so get the FSM for your car, your engine and your country
The DI chapter covers this. read that yet? diagnosis?
did you use the scan tool an see what up's up or not ?

your engine really is.
1CD-FTV I4 (diesel)
that is the correct name, so study only that)

no start hot.
its too much fuel or tool little?
to little?
did you try test fuel to see if loss of fuel is the problem?
on diesel it's poor compression
or lost fuel , hot starts.
easy huh , no spark to check , there is no spark
some diesels have 1 sensor for injector timing.
if flooding , you get black smoke out the tail pipe, so id suspect
you'd have noticed that and did not see it.
test fuel, tests.
if this fails, a full hot compression test. its not the cam belt slippped
if runs ok cold,

i bet the injectors are shut down
the PCM tell you why, so let it.
SCAN it. after 5 seconds cranked.
almost all PCM report 1 bad pulse of 10 in all speed sensors.
(CKP or CMP )

Feb 24, 2014 | 2002 Toyota RAV4

1 Answer

2001 f350 diesel wont start without starting fld after wormed up

Starting fluid is a bad idea on glow plug engines. Some things to check are, the IDM, TPS, crank sensor, cam sensor, wires running through valve cover gasket, glow plug controller, ECM. Have the codes ran first. Could be one of the fuel pumps, but not common.

Dec 16, 2012 | 2006 Ford F 350 Super Duty

1 Answer

Gets warmed up then will not start until cool. Replaced crankshaft sensor did not fix problem

Are you a diesel engine if you are its the cam position sensor, its on the lower front on the driver side,they are common symptoms it warms up and you stall, just replace it ,make sure connections are good,

May 04, 2011 | 2006 Ford F 350 Super Duty

1 Answer

97 F 350 Diesel fuel problems

Again check your cam sensor

Mar 06, 2010 | 1997 Ford F350 Crew Cab

1 Answer

I rebuilt a 350"R" vortec in a 1998 GMC suburban. It runs good except for a slight cutting out sometimes. It always has a code P1345. After erasing the check eng. light will come on almost immediatly after...

I take it,you replaced the crankshaft sensor,now,the cam sensor(pick up coil)is most likely the problem,it is either not lining up,or,there is wear in the distributor.The crankshaft sensor is not aligning with the cam sensor(pick up coil).

Feb 25, 2010 | GMC Suburban Cars & Trucks

Not finding what you are looking for?
2004 Ford F350 Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

5648 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides