Question about 2000 Toyota Corolla

1 Answer

Flywheel My corolla also has a knock it has had three flywheels replaced and im looking at a fourth

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 1,861 Answers

Have whoever is changing the flywheels check the crankshaft for "end play"...If the crankshaft thrust bearings are worn, it will allow the shaft to "walk" , or shift back & forth in the block. This action will def damage flywheels over time.

Posted on Oct 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 cadillac deville flywheel replacement


1979 Cadillac Coupe 425 engine running; flywheel knocking

? 1:16
https://www.youtube.com/watch?v=UTDBmkKyBCY
Sep 30, 2011 - Uploaded by Edgar H
1979 Cadillac Coupe 425 engine running; flywheel knocking ...Change Transmission Fluid pan removal Cadillac Seville part1 - Duration: .

Exclamation Re: Found a 94 STS for $800, needs flywheel ...

www.cadillacforums.com/.../cadillac-seville-cadillac.../65815-found-94-s...

Feb 16, 2006 - 15 posts - ‎9 authors
Cadillac Seville / Cadillac Eldorado Forum Discussion, Found a 94 STS for $800, needs .... If it is somehow just the flywheel, your repair cost would be the labor involved in dropping ... Automobile(s): 1999 STS - diamond white. Re: flywheel 99 sts
14 posts
Apr 7, 2013
Re: need to replace flywheel
3 posts
Dec 3, 2011
Re: Location of transaxle to engine bolts on 1998 ...
15 posts
Nov 13, 2011
Re: How to lock flywheel without $150 tool?
7 posts
May 21, 2009
More results from www.cadillacforums.com

Jan 11, 2016 | Cadillac Cars & Trucks

2 Answers

Toyota corolla 2005 knocking issue when fast accelerate


Simple
Replace engine no way around this one
Knocking and loss of power is engine failure coming
Possible burn pistons and bad rings
Replacing engine cheaper than rebuilding one

Feb 28, 2015 | 2005 Toyota Corolla

1 Answer

Knocking noise from tires when accelerating


The noise may be your driveshaft ujoint going bad making the noise when you speed up,turn your driveshaft back and fourth by hand and see if it makes any noise. Jim Riley said that.

May 26, 2012 | 1994 Toyota Tercel

1 Answer

My car is a manual transmission. But when i use the 4th gear, it automatically comes to nutral gear, whats the problem?


if its jumping out of fourth back into nuetral then you have 2 options,both involve taking out the gearbox.
1/replace the baulk ring on fourth gear or
2/ get a recon box(poss the easiest,as all rings/bearings will have been replaced).

May 04, 2010 | 1991 Toyota Corolla

1 Answer

1994 Toyota Corolla DX starting problem?


you need to replace the starter contacts, you will need to remove the starter and in the starter there are "contacts" that wear out over time and will need to be replaced im sure if you google it there will be better repair tips on this

Mar 07, 2010 | 1994 Toyota Corolla

2 Answers

Where is the knock sensor on a 96 corolla?


the knock sensor is located at the center of the engine in the rear, heres a diagram witha list of the sensor locations,it shows the knock sensor, it looks like its in the front of engine but its not its in the rear, good luck.d49f3fd.gif

Feb 23, 2010 | 1996 Toyota Corolla

2 Answers

Motor has a knock in the lower part of motor. The knock is there al the time


hello, sounds like you have bad rod bearing, or rod cap could be wore out, try lucas oil if it does not quiet down then you probably have rod bearing going out, wouldnt drive unless you have too. untill you get checked

Feb 06, 2010 | 2001 Jeep Grand Cherokee

1 Answer

I have an 95 corolla and it was auto and im convering it to stick and the tranny gos on not all the way i can cach one bolt but not all the way


Sounds like the clutch plate is not aligned with the transmission pinion. Also check to make sure the clutch plate was not installed in reverse. Your pressure plate should be installed flush with the flywheel. If you are not using a clutch alignment tool, you should.

Nov 05, 2009 | 1994 Toyota Corolla

1 Answer

Knocking noise in engine 1998 jeep cherokee


Knocking noise can come from one of three places. Broken flywheel, Worn rod or main bearing. (bearing problems usually are accompanied by lowered oil pressure) An experienced technician can usually tell which is which. If bearing wear is on the rod bearings only and is light, it can usually be corrected. Main bearings require engine removal and is far more expensive. The oil pump should be replaced with either, but is not the cause of the problem. Extreme wear on bearings will also damage crankshaft. If so, it must be replaced.

Jun 16, 2009 | 1998 Jeep Cherokee 4WD

1 Answer

What does code 52 means on the toyota corolla 2000 model in SA.


DTC 52 on a 93 Corolla is a Knock Sensor code. I replace the knock sensor; it is located on the side of the engine block, on the side of the engine that faces the firewall. It is in the center; under the intake manifold.

Thanks for choosing FixYa for assistance.

Mar 09, 2009 | 1993 Toyota Corolla

Not finding what you are looking for?
2000 Toyota Corolla Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...