Question about 1999 Chrysler Town & Country

1 Answer

No dash lights and no tail lights

Gauges all work just no lights. Stop lights and blinkers work. no side or tail lights. have checked bulbs and fuses

Posted by on

  • Anonymous Mar 13, 2014

    1997 300tdi discovery 1 dash and side light bulbs not working its not the fuses or bulbs so would like to know where a possible earth fault could be

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Check for faulty wires at the fuse block, had one fall off from the block itself from the rear, or it could be a wire break somewhere along the way.

Stop Lights and Blinkers are independant fuse.

Tail lights are on there own fuse and could be a wire break in the rear or removing the bulb and using a metre check for signal at bulb socket where trouble is, Check for disolored connections, Green in color or simular, could be a bad connection which in turn is not letting the curent to other side, Causing a short and loss of power to all remaining lights in curcuit.

Posted on Sep 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Right indicators not working on Mercedes 270ml, hazards only work on left side. Only checked back bulb(not blown) fuse not blown either. Any help appreciated


check right side bulbs to verify they are correct bulbs especially the tail light bulbs.....commen on imports...if all Bulbs are good then replace flasher unit under dash....before replacing blinker lever at steering column

Aug 13, 2016 | Cars & Trucks

1 Answer

The gauge/gear/temp control lights do not work. Tail lights are fine. Bulbs are fine, replaced 2 fuses but problem persists, what to do??


The dash lights are on a different fuse and circuit from the tail lights.
If the lights in the instrument cluster work, the problem may be in the harness in the dash.

Feb 16, 2015 | 2000 Saturn Ls 4dr Sedan

2 Answers

My tail lights are not working on my 2000 jetta the front lights work the break lights work and the blinkers work all inside lights work just fine


you need new bulbs in tail lights one bulb in each side has two elements one works brake other works running lights the elements in the bulb for tail lites are bad . so just replace bulbs. hope this helps.

Sep 13, 2011 | 2002 Volkswagen Jetta TDI

2 Answers

1988 pathfinder no dash lights no revers lights no tail lights no gaiges


If they all stopped working at the same time then it is probably a fuse or possibly 2. Check your fuse panels in the dash and under the hood. The dash lights and gauges should be a fuse labeled instrument cluster or guages, it is probably blown. The other fuse to look for will be the tail light fuse. This is where I would begin.

Sep 23, 2010 | 1988 Nissan Pathfinder

1 Answer

My blinker lights stop blinking and the fuse box doesn't have a cover to show which fuse is which so i do not no which fuse is for the blinker lights.


change the bulb sometimes one of the filaments where out they are combo bulbs usually 1157 1156 bulbs back stop and tail combo bulbs, or check owners manual, this is depending on your type of vehicle but thats probably it.

Jul 07, 2010 | Cars & Trucks

1 Answer

Brake Lights and Hazard still dont work


TEST FRONT RIGHT BLINKER CIRCUIT AND REPLACE THE BULB,,WITH PROPER BULB...A DOUBLE CIRCUIT BULB IN A SINGLE SOCKET WILL DO THAT ALSO A SINGLE SOCKET BULB IN A DOUBLE SOCKET HOLDER....CHECK LEFT SIDE BULB FOR ACURANCY

Aug 29, 2009 | 1993 Chevrolet Astro

1 Answer

Left rear tail lights/ blinker will not come on


Blinker too fast, the same side blinker light bulb on the front (or back) is burned. Check the fuses for the rear lights. You might have a light bulb filament stuck.

Mar 30, 2009 | 2006 Dodge Charger

1 Answer

99 mercury mystide had rear running light broken


If the driver's side tail light is working, it's not a fuse. Use a test light to check for power at the bulb holder. One terminal will be for tail light, the other for brake/turn light. If the is constant power for tail light, replace bulb. If no power, trace wiring from bulb holder to driver's side junction. Probable broken wire between the two tail lights.

Jan 16, 2009 | 1999 Mercury Mystique

1 Answer

Left blinker light stays on solid when headlights are on


I have had this happen and it is rare, but I have had a filiment burn out in a two filment buld and short to the other filiment. It does happen and I think this might be your problem, the only way to find it is a visual inspection of each bulb. I am sure many people will think this is crazy, but I have had the exact same problem, I had the schematics, tested the circuits,etc. and them by accident found a stop/blinker 1157 bulb that had done this exact thing. I hope this helps you, check the bulbs in your headlights also.

Dec 27, 2008 | 1999 Chrysler LHS

Not finding what you are looking for?
1999 Chrysler Town & Country Logo

407 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...